Stiga T8521 Manual de usuario

O W N E R ’ S M A N U A L

Escalade® Sports products may be manufactured and/or licensed under the following patents.

6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431

Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

2L-4242-00

TABLE TENNIS TABLE

MODEL NO.

T8521

2015 Escalade Sports

Contact Escalade® Sports customer service department at:

Phone: 1-866-873-3528 Toll-Free!

Fax: 1-866-873-3533 Toll-Free!

E-mail: [email protected]

Please Do Not Return This

Product to the Store!

Contact Escalade® Sports customer service department at:

Phone: Toll – Free !

Fax: 1-866-873-3533 Toll – Free !

E-mail: tabletennis@escaladesports.com

Mailing Address (correspondence only):

Escalade Sports

PO Box 889

Evansville, IN 47706

1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.

2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering

parts.

3. To make assembly easier, use the Hardware Identifier on page 3 to identify and sort all fasteners. Check all cartons for kits. All

hardware may not be located in one kit.

4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and parts

may not easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.

5. Tools required for assembly: Phillips Screwdriver, Two 9/16” Wrenches, Two 7/16” Wrenches (Ratchet and 9/16”, 7/16” Sockets are

recommended and can be substituted for wrenches).

6. An electric screwdriver is helpful in assembly. However, please set at low torque and use caution because you could over-tighten screws.

7. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for

replacement parts.

Please Do Not Return This Product To The Store!

Please visit our Website at:

www.escaladesports.com

ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE

ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS

ADDITIONAL ESCALADE®

SPORTS PRODUCT INFORMATION

P R E - A S S E M B L Y T I P S

2015 Escalade Sports

P R E - A S S E M B L Y T I P S

1-866-873-3528

1/4"

Plastic

Washer Washer

Plastic

3/8"

28 30

32 5

35 37

1/4-20 X 3 1/4 Carriage Bolt #8 X 9/16

SMS

#8-32 X 1 1/4

Sheet Metal Screw 3/8" Long Spacer

3/4" Long Spacer

1/4-20 X 2 3/4 Hex Head Bolt

HARDWARE IDENTIFIER

3/8-16

Locknut 1/4-20 X 1 1/2 Phillips

Truss Head Screw

1/4-20

Locknut

3/8-16 x 3 1/2 Hex Head Bolt

(Qty. 4) (Qty. 20)

(Qty. 4)

(Qty. 4) (Qty. 4) (Qty. 4)

(Qty. 4) (Qty. 4) (Qty. 4) (Qty. 4) (Qty. 8)

(Qty. 4)

1/4-20 Wing Nut

Sorting your hardware ahead of time will speed up assembly time. Sort

all your hardware now so it will be ready before you start assembly.

NOTE:

1. Attach Wood Bottom Board (#15) to Caster Beam Assemblies (#8)

as shown in Figure 1. Turn Caster Beams as shown and attach

board with four Carriage Bolts (#31) and four Wing Nuts (#32).

Tighten Wing Nuts securely.

(Qty. 4)

1/4-20 Wing Nut

Caster

with

Lock

HARDWARE NEEDED

1/4-20 X 3 1/4 Carriage Bolt

(Qty. 4)

NOTE: Make sure logos are right side up and

facing the outside as shown.

Figure

32 Caster

with

Lock

Note: Support Plate (#43)

is on the inside of Caster

Rail (#8) as shown.

READ AND FOLLOW ALL ASSEMBLY, OPERATING, AND

SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO (2)

ADULTS ARE NEEDED TO PUT THIS TABLE TOGETHER!

CAUTION:

ASSEMBLY TIP

On the top of each page you will find a picture of the

Hardware Needed (to scale) along with the Quantity,

Key# and Description. You can lay the hardware on

the picture to identify and sort the hardware.

2. Attach Strut Tubes (#17) and White Linkages (#16) to Caster Beam Assemblies (#8) as shown in Figure 2.

a) If necessary loosen Bolts (#13) and Nuts (#28) so that Strut Tube (#17) can fit between Support Plate (#43) and Caster

Beam (#8) as shown in the Top View and Figure 2.

b) Slide one Hex Bolt (#27) through one linkage (#16) one Spacer (#36) pass through Caster Beam (#8), followed by one

Plastic Washer (#39), Strut Tube (#17), another Plastic Washer (#39), inner Support Plate (#43) and Lock Nut (#28).

c) Repeat on other end of Caster Beam (#8) and on second Caster Beam.

d) Tighten Nuts (#28) on Bolts (#13) securely.

e) Tighten Nuts (#28) on Bolts (#27) securely.

Note: Linkages & Strut

tubes must be turned as

shown or table will not

operate correctly.

39 12

(Inner Plate)

TOP VIEW

3/8-16

Locknut

(Qty. 4)

HARDWARE NEEDED

27 3/8-16 x 3 1/2 Hex Head Bolt

(Qty. 4)

36 39

3/4" Long Spacer

(Qty. 4)

3/8" Plastic

Washer (Qty. 8)

Note: Dimples on Strut

Tubes are part of the

manufacturing process and

do not affect assembly.

Figure

If you want to see a video on how to insert Screw (#35) go to:

http://www.escaladesports.com/customer-service/instruction-videos

Scan with your smartphone:

3. Rotate U-support (#21) that is on bottom of Table Top until you see the screw holes in the slots of U-clips (#22).

If necessary Slide U-support (#21) side to side and back and forth to see holes. See Figure 3 & Detail A.

4. Insert Screw (#35) through slot in U-clip (#22) and into U-support (#21). See Figure 3 & Detail A.

Thread screw all the way into U-support until it touches the back of the tube. There should be about

3/8” of screw (#35) left sticking out. Repeat for second Screw (#35) and U Clip (#22).

NOTE: To aid in assembly use a cordless drill but DO NOT over tighten screws. Wear safety glasses.35

HARDWARE NEEDED

#8-32 X 1 1/4

Sheet Metal Screw

(Qty. 2)

Detail A

Note: This end has NO stripe.

Figure

NOTE: Prepare an area for the assembly of the second table top half. If necessary,

move the first table top half aside with the aid of a helper. Be sure to place it in a

location where it won't be disturbed or damaged. If setting on its side, be sure to

place the bottom edge no less than 12 inches away from the wall. Also be sure to

place carpet or pieces of the shipping carton down to protect table top edges. If

floor is not carpeted, brace table top half with a heavy object to keep it from sliding.

5. Repeat step 3-4 to complete a second Table Top Assembly.

6. Attach Table Top Assembly to Base Assembly as

shown in Figure 4. Pivot Strut Tubes (#17) up as

shown; then, with at least one adult on each

side of Table Top, lift top and align ends of U-

support tube (#21) with tops of Strut Tubes (#17)

as shown in Figure 4. Lower the table in a

controlled manner and as even as possible so the

Strut Tube goes in the U-Support evenly. Carefully

slide tubes together.

DO NOT OPEN THE TABLE TO PLAYING POSITION

UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE

TABLE STANDING UNATTENDED. IT COULD BE

KNOCKED OVER CAUSING SERIOUS BODILY INJURY

OR PROPERTY DAMAGE.

COMPLETE THE REST OF THIS ASSEMBLY! WHEN

ASSEMBLING TOPS TO BASE, HANDLE TOP

ASSEMBLIES BY GRASPING ONLY THE TOPS

THEMSELVES. DO NOT GRASP METAL LEGS, U-

SUPPORT, LINKAGE, OR HINGES. THESE PARTS

CAN MOVE AND COULD PINCH FINGERS OR

HANDS CAUSING SERIOUS INJURY! ASSEMBLE

AS SHOWN WITH LEGS FULLY CLOSED AND

TOPS IN A VERTICAL POSITION. DO NOT OPEN

Y TO ASSEMBLE. TABLE TOPS ARE

LEGS AND TR

HEAVY -

ALONE!

DO NOT ATTEMPT TO ASSEMBLE

HEAVY -

AT LEAST TWO (2) ADULTS ARE NEEDED TO

TUBES UP

Table Top

Assembly

U-Support

Strut Tube

With at least 2 adults,

slide Table Top Assembly

onto Strut Tubes (#17).

Strut Tube

PIVOT STRUT

Figure

ATTENTION: If hinge is positioned as

shown here (Detail B), Rotate the hinge as

shown in Detail C. Do not take hinge off.

Hinge Assembly

with “elbow”

pointing down.

Plastic Washer goes

between Strut Tube

(#17) and Hinge (#18)

Or Scan QR code with

your smartphone:

DO NOT OPEN THE TABLE TO PLAYING

POSITION UNTIL BOTH TOPS ARE

INSTALLED! DO NOT LEAVE TABLE

STANDING UNATTENDED. IT COULD BE

KNOCKED OVER CAUSING SERIOUS

BODILY INJURY OR PROPERTY DAMAGE.

HARDWARE NEEDED

30 38

1/4" Plastic

Washer

1/4-20 Locknut

(Qty. 2) (Qty. 2)

1/4-20 X 1 1/2 Phillips

Truss Head Screw

(Qty. 2)

CAUTION: Position hinges exactly as

shown in Detail C or table will not

operate correctly and could be damaged.

Elbow

Detail B

Detail C

Incorrect position

of hinge with elbow

pointing up.

In the correct position Hinge #18

will look like a “V” when attached

to Strut Tube (#17).

Hinge Assembly

with “elbow”

pointing down.

Correct position

of hinge with elbow pointing down

Elbow

If you want to see a video on how to attach hinges to Strut tube go to:

http://www.escaladesports.com/customer-service/instruction-videos

7. Attach Hinges (#18) to Strut Tubes (#17) as shown in Figure 5 & Detail C. With

hinge positioned as shown, align hole in hinge with hole in Strut Tube and attach with

¼” Screw (#30), Plastic Washer (#38) and Locknut (#34). Plastic Washer (#38) goes

between Strut Tube and Hinge. Tighten nut securely. Repeat for other Hinge.

CAUTION: Hinges must be positioned exactly as shown or table will not

operate correctly and could be damaged.

Figure

Note: If hinge (#18) is positioned as shown in Detail B, you will have to rotate the hinge

to the position shown in Detail C. DO NOT unscrew the hinge, you can rotate the hinge

without unscrewing it from the table.

10. With at least two adults, repeat Steps 7-9

for other table top assembly.

9. Attach Linkages (#16) to Leg (#19) as shown in Figure 6. Pivot Leg (#19)

out from the table top and pivot both linkages (#16) up and align hole in

Linkage with hole in Leg (#19). Attach Linkage (#16) to Leg (#19) using

Hex Head Bolt (#29), Spacer (#37) and Locknut (#34). Spacer (#37) goes

between Linkage and Leg. Attach other Linkage to Leg the same way.

Tighten nuts securely.

HARDWARE NEEDED

1/4-20 Locknut

(Qty. 2)

Spacer goes between

Linkage Arm (#16) and

Leg (#19)

8. Secure U-support tube (#21) to Strut Tubes (#17) with two Screws (#5) as

shown in Figure 6. Align holes in U-support with holes in Strut Tubes and

thread screw (#5) into hole in Strut Tube (#17). Tighten screws all the way

but be careful not to over tighten as you could strip threads on screws.

Note: Make sure

to install #5

screws

Note: Make sure

to install #5

screws

DO NOT OPEN THE TABLE TO PLAYING

POSITION UNTIL BOTH TOPS ARE

INSTALLED! DO NOT LEAVE TABLE

STANDING UNATTENDED. IT COULD BE

KNOCKED OVER CAUSING SERIOUS

BODILY INJURY OR PROPERTY DAMAGE.

37 5

1/4-20 X 2 3/4 Hex Head Bolt

(Qty. 2) 3/8" Long Spacer

(Qty. 2)

#8 X 9/16

Screw

(Qty. 2)

Figure

CAUTION:

TO CLOSE:

1. Pivot the net post toward side of the table.

2. Unlock all four hinges.

3. Lift one table half to midpoint until the

plastic clips are engaged. Then continue

lifting until closed.

4. Raise other table half in the same manner.

....as shown in Figure 9.

TO OPEN:

1. Hold center of top edge. Gently pull outward to midway position.

.... Continue to pull until disengaged from plastic clips and legs rest on the

....floor as shown in Figure 7A and 7B. Do not leave table partially

....opened at midway position.

2. Lower second top as described in step 1.

3. Lock all four center hinges. See Figure 8.

4. Attach net posts and net to table as shown in the next page (11).

NOTE: Net will be tight. It will be necessary to stretch net. This will insure

proper net tension.

PLAYING POSITION

IF TABLE IS NOT ALIGNING CORRECTLY: (see Figure 10)

1. Set the table to the Playing Position and lock hinges as shown in

....Figure 8.

2. Loosen Wing Nuts (#32) attached to bolt (#31) in order to create

....enough slack to align table tops. See .Figure 1 on page 4

3. With the help of two other adults, push the two table top halves so

.... they are in line with each other and re-tighten the Wing Nuts (#32) as

....shown in .Figure 10

OPENING AND CLOSING INSTRUCTIONS

Push to lock hinge.

Plastic

Clip

EXERCISE CAUTION IN OPENING/CLOSING TABLE. SMALL CHILDREN, OR

CHILDREN NOT PROPERLY INSTRUCTED IN ITS USE, MUST NOT BE ALLOWED TO OPEN/CLOSE

TABLE. IMPROPER HANDLING AND MISUSE CAN RESULT IN SERIOUS INJURY OR DAMAGE.

DO NOT CLIMB, STAND, OR JUMP ON TABLE. MOISTURE AND CONDENSATION WILL

DAMAGE PLAYING SURFACE OF THIS TABLE. STORE IN DRY, INDOOR PLACE.

Midway

Position

PLAYBACK POSITION

Hinge

Locked

Tabla de contenidos

Idiomas:

Otros manuales de Robótica de Stiga

Manuales populares de Robótica de otras marcas

STEMCenter USA

STEMCenter USA Pi-Bot v2.00 Manual de usuario

SunFounder

SunFounder PiDog Manual de usuario

Universal Robots

Universal Robots UR5 Manual de usuario

Universal Robots

Universal Robots E Series Manual de usuario

YASKAWA

YASKAWA MOTOMAN-MPL80 II Manual de usuario

EFORT

EFORT ECR5 Manual de instrucciones

Epson

Epson C8 Series Manual de usuario

WowWee

WowWee ROBOQUAD Manual de usuario

Milvus Robotics

Milvus Robotics SEIT 100 Manual de usuario

RoboMaster

RoboMaster AI Robot 2020 Standard Version Manual de usuario

fischertechnik

fischertechnik Mini Bots Manual de usuario

YASKAWA

YASKAWA MA2010 Manual

Abicor Binzel

Abicor Binzel iCAT mini Manual de usuario

ABB

ABB OmniCore E10 Manual de usuario

YASKAWA

YASKAWA Motoman DX200 Manual de usuario

pitsco

pitsco Tetrix Max Manual de usuario

ECOVACS

ECOVACS DEEBOT R95 Manual de usuario

Feng Yuan

Feng Yuan Interstellar Warrior Manual de usuario