Steelcase Power Panel Supply System Manual de usuario

Steelcase, Inc.

Grand Rapids, MI 49501

U.S.A.

1-888-783-3522

Tools

Assembly Directions Printed In U.S.A.

REV

93-9500856 A

Page 1 of 14

Power Panel Supply System

IMPORTANT: All electrical installations should be done

by a qualified electrician in accordance with codes and

regulations applicable at the installation site.

3/8” DRILL BIT

Assembly Directions

93-9500856 REV APage

2 of 14

Factory Installed Outlet Box Package

For models PPB-24-X thru PPB-48-X non-branching

and models PPB-24B-X thru PPB-48B-X branching

For assembly directions see page 4

Field Installed Outlet Box Package

For models F-PPB-24-X thru F-PPB-48-X non-branching

and models F-PPB-24B-X thru F-PPB-48B-X branching

For assembly directions see page 12

OUTLET BOX

OUTLET BOX (non-branching)

OUTLET BOX (branching)

BASE

COVERS

RECEPTACLE OUTLET

COVER PLATES

POWER

PANEL

ASSEMBLY

BASE

COVER

RECEPTACLE OUTLET

COVER PLATE

Assembly Directions

93-9500856 REV APage

3 of 14

Pass-Thru Power Distribution Cables

Models PDC-18 thru PDC-72

For installation directions see page 7 & 8

Adjacent Panel Power Distribution Cables

Model PDC-A

One size connects any two adjacent power panels

For installation directions see page 6 & 8

Power Source Box

Model PSB-1

For installation directions see page 11

Power Source Cable

Models PSC-36, PSC-72, & PSC-144

For installation directions see page 9

Installing Telephone Cable

For installation directions see page 14

Assembly Directions

93-9500856 REV APage

4 of 14

Before proceeding with the installation of your power panels included with factory installed outlet boxes, check your

space plan or floor layout diagram. Proper location of the pre-wired and pass-thru panels within the workstation is

important to the success of your installation. Be aware of the location of your building power and telephone cable

sources. A typical work station is shown below.

Important: Do not exceed the maximum allowable number of outlets on a circuit. Consult your local electrical

code requirements.

A-Panel outlet box

B-Pass-thru power distribution cable (PDC-30)

C-Adjacent panel power distribution cable (PDC-A)

D-Power source electrical

E-Telephone source

Assembly Directions

93-9500856 REV APage

5 of 14

Preparing Your Panel Assembly For Wiring Components

Remove tape from both ends of panel assembly. 2. Remove both base covers by pulling outward at the

bottom extreme ends (in area of glides) and lifting

straight up. Remove and retain receptacle outlet

cover plates for assembly at a later step.

3. Remove base end cap knock-out by placing

pliers at the bottom forcing it to break free from

base end cap.

4. Care should be taken not to damage base end caps.

PANEL

ASSEMBLY

TAPE

BASE END CAP

BASE COVERS

RECEPTACLE

OUTLET COVER PLATE

BASE END CAP

KNOCK-OUT

BASE END CAP

Assembly Directions

93-9500856 REV APage

6 of 14

Attaching Adjacent Panel Power Distribution Cables

CAUTION: Do not make or break electrical connections under load.

NOTE: One size distribution cable fits any two adjacent power panels.

When connecting the outlet box in one panel to the outlet box in an adjacent panel use power distribution cable model

PDC-A (approximately 20” long). Insert cable head into either of the two modules in one outlet box. Be sure cable

head is inserted until grippers securely engage lip of modules. Cable head should snap in place when correctly inserted.

Connect the opposite end of cable to either of the two modules of outlet box in adjacent panel. Untwist tag-wire and

remove hex nut from ground wire. Place the end of ground wire onto bolt threads and secure with hex nut. For panels

positioned at angles refer to Steelcase Direction 93-9500732-P for installation of corner covers. See page 10 of these

directions when replacing base covers.

HEX NUT

OUTLET BOX

MODULES

POWER DISTRIBUTION CABLE

GROUND

WIRE

GRIPPERS

CABLE HEAD

GRIPPERS

OUTLET BOX

MODULESMODULES

OUTLET BOX

HEX NUT

TAG-WIRE

OUTLET BOX

CABLE HEAD

HEX NUT

POWER DISTRIBUTION CABLE

GROUND

WIRE

Assembly Directions

93-9500856 REV APage

7 of 14

Attaching Adjacent Panel Power Distribution Cables

CAUTION: Do not make or break electrical connections under load.

NOTE: One size distribution cable fits any two adjacent power panels.

When connecting the outlet box in one panel to the outlet box in another panel with one or more panels between the

two without power, a pass-thru power distribution cable of proper size is used. Insert cable head into either of the two

modules in one outlet box. Be sure cable head is inserted until grippers securely engage lip of modules. Cable head

should snap in place when correctly inserted. Lay cable into the non-powered panels and connect the opposite end

of cable into either of the two modules of outlet box in the next powered panel in your system. Untwist tag-wire and

remove hex nut from ground wire. Place the end of ground wire onto bolt threads and secure with hex nut. See page

10 of these directions to replace base cover.

OUTLET

BOX

CABLE HEAD GRIPPERS

POWER DISTRIBUTION CABLE

HEX NUT

TAG-WIRE

MODULES OUTLET BOX

This chart illustrates the power distribution cable model used for

various (width) size panels or a combination of various sized panels.

MODEL NO. FOR PASSING THRU FOR PASSING THRU MORE THAN (1) PANEL

PDC-18 18” wide panel

PDC-24 24” wide panel

PDC-30 30” wide panel

PDC-36 36” wide panel (2) 18” wide panels

PDC-42 42” wide panel (1) 18” plus (1) 24” wide panels

PDC-48 48” wide panel (2) 24” or (1) 18” plus (1) 30” wide panels

PDC-54 (1) 24” plus (1) 30” or (1) 18” plus (1) 36” wide panels

PDC-60 (2) 30” or (1) 24” plus (1) 36” or (2) 18” plus (1) 24” wide panels

PDC-66 (2) 24” plus (1) 18” or (1) 36” plus 30” or (1) 30” plus (2) 18” wide panels

PDC-72 (2) 36” or (2) 18” plus (1) 36” or (3) 24” or (1) 48” plus (1) 24” wide panels

Assembly Directions

93-9500856 REV APage

8 of 14

Branching

CAUTION: Do not make or break electrical connections under load.

NOTE: When installing power panels consult your local electrical code requirements as a guide for the maximum

allowable numerous outlet boxes for a branch circuit. Outlet boxes and power distribution cables shown below are one

of the following models PDC-A or PDC-18 thru PDC-72.

Insert cable head into either of the two modules in outlet box. Be sure cable head is inserted until grippers securely

engage lip of modules. Cable head should snap in place when correctly inserted. Connect the opposite end of cable

in the same manner. Untwist tag-wire and remove hex nut from ground wire. Place the end of ground wire onto bolt

threads and secure with hex nut. Replace base covers. For installation of corner covers see Steelcase Direction

93-9500732-P.

Installation of power distribution cables

OUTLET BOX

MODULE

CABLE HEAD

GROUND WIRE

POWER DISTRIBUTION

CABLE (TYPICAL)

HEX NUT

TAG-WIRE

GRIPPERS

HEX NUT

OUTLET BOX

MODULE

CABLE HEAD

GROUND WIRE

POWER DISTRIBUTION

CABLE (TYPICAL)

GRIPPERS

HEX NUT

TAG-WIRE

Assembly Directions

93-9500856 REV APage

9 of 14

Branching

CAUTION: Do not make or break electrical connections under load.

Remove base cover.

2. Locate conduit clamp and secure with (1) 1/4-20 phillips head screw.

3. Insert cable head into the top module in outlet box. Be sure cable head is inserted until grippers securely engage

lip of module. Cable head should snap in place when correctly inserted. Place cable into conduit clamp and secure

with (1) 10-24 phillips head screw and (1) 10-24 nut. Replace base covers.

SCREW 1/4-20

CONDUIT CLAMP

CABLE

NUT 10-24

SCREW 10-24

CABLE HEAD

OUTLET BOXGRIPPER

OUTLET BOX

Assembly Directions

93-9500856 REV APage

10 of 14

Branching

Place notches of electrical base cover over spring retainers and snap top flange into place making sure the cutout in

the base cover is aligned with receptacle (part of outlet box). Remove screw from receptacle and secure receptacle

outlet cover in place.

SPRING RETAINER

RECEPTACLE (PART OF OUTLET BOX)

NOTCHES

BASE COVER

RECEPTACLE OUTLET COVER

SCREW

Otros manuales de Equipos de oficina de Steelcase

Steelcase

Steelcase a3 CeramicSteel Sans Manual de usuario

Steelcase

Steelcase V.I.A. FEIJA2V Manual de usuario

Steelcase

Steelcase Wood Selections Worksurface Actualización de firmware

Steelcase

Steelcase Avenir Storage Bin Actualización de firmware

Steelcase

Steelcase Montage In Manual de usuario

Steelcase

Steelcase Context Actualización de firmware

Steelcase

Steelcase Migration LTD Manual de usuario

Steelcase

Steelcase Activa Lift 2 Manual de usuario

Steelcase

Steelcase media:scape Kiosk Manual de usuario

Steelcase

Steelcase Pathways Privacy Screen Infill Manual de usuario

Steelcase

Steelcase TS Series Manual de usuario

Steelcase

Steelcase Series 5 Manual de usuario

Steelcase

Steelcase Elective Elements Fixed Modesty Panel Manual de usuario

Steelcase

Steelcase Details Airtouch Manual de usuario

Steelcase

Steelcase Avenir Movable Walls PAB-9 Joining Panels Manual de usuario

Steelcase

Steelcase TouchDown2 Manual de usuario

Steelcase

Steelcase Criterion Manual de usuario

Steelcase

Steelcase Avenir PAB-4 Joining Panel Manual de usuario

Steelcase

Steelcase FlipTop Twin Manual de usuario

Steelcase

Steelcase Migration SE Boundary Screen Manual de usuario

Steelcase

Steelcase 9000 Series Manual de usuario

Steelcase

Steelcase Avenir PAB-3 Manual de usuario

Steelcase

Steelcase Turnstone Smoke Manual de usuario

Steelcase

Steelcase Avenir Panel Manual de usuario

Manuales populares de Equipos de oficina de otras marcas

silen

silen Space 2 Manual de usuario

Middle Atlantic Products

Middle Atlantic Products LD Series Manual de usuario

SHFL

SHFL DECK MATE BLACKJACK Manual de usuario

DROMEAS

DROMEAS LINE Manual de usuario

Siemens

Siemens HIPATH 2000 Manual de usuario

VITRA

VITRA Stefan Hürlemann Dancing Wall Manual de usuario

BISLEY

BISLEY Glide V2 Manual de usuario

fully

fully Haven Manual de usuario

Plus

Plus NF-20 Manual de usuario

OCEE DESIGN

OCEE DESIGN SASS-0100 Manual de usuario

NanaWall

NanaWall CSW75 Manual de usuario

Vivo

Vivo DESK V000C Manual de usuario

ABB

ABB 2TKA002145G1 Manual de usuario

PolyVision

PolyVision Flow Manual de usuario

MBM

MBM FC-10 Manual de usuario

Wiremold

Wiremold V2400 Series Manual de usuario

Vivo

Vivo PP-3-T072D Manual de usuario

BuzziSpace

BuzziSpace BuzziNest Booth Manual de usuario