AConnect the power adapter.
BConnect the Ethernet cable to the NAT/Router.
CThe IP Camera will get an IP address
from the NAT/Router (with DHCP enabled) automatically.
Check if the red LED of the IP camera is always on.
If it’s blinking, please check step A and step B again.
LANWAN
Power Adapter
Ethernet Cable
NAT or Router
Internet
Please download the latest
CamView software at this address :
http://www.starvedia.com/download.html
After the setup menu pops up, select
“Install Management Software” and follow
the instructions.
Press the WPS button
on the camera.
The CamView software will list
the searched camera on the
“Auto search” section
Drag the camera from the“Auto
Search” section to the “Camera
List” section.
Right click the camera on
the camera list and choose
the ID/Password Settings.
Key-in the password given on the
ID/Password Card and then you
will be able to see the video.
Unplug the Ethernet
cable from the camera.
Press the WPS button on the NAT/Router,
the LEDs on the IP Cam will start blinking.
If the LEDs stops blinking and remain on,
the wireless connection has been
established successfully.
Click the “Network” → “WiFi Security”.
Click on the “Wi-Fi Scan’’ button, Choose the wireless AP.
(If the scan failed, please check the antenna or the Wi-Fi Access Point.)
On the camview software, right click on the camera you want to setup
on the “Auto Search’’ area and click on
“Web Configure’’. Enter the admin username and password.
The default admin username: admin.
The default password is empty (leave blank)
5.2 Wireless Connection Settings
If the router has no WPS function, please follow STEP 1 and make sure the Ethernet cable is
connected to the Camera and then follow the steps below to setup the wireless connection.
5.4 Unplug the Ethernet Cable from the Camera
to start the Wireless Connection
If the Wi-Fi test has been successful, unplug the Ethernet cable from the
camera. The red and blue LEDs will remain on once the wireless connection
is operational.
The Wireless connection will not function if you do not remove the Ethernet
cable from the camera.
TKIP
1234567890
64 bits(10 hex digits)
Enable WiFi function
SSID wifi-test
Security mode
WEP Encryption
WEP Key
WEA Encryption
WPA-PSK KEY
Save & Apply WiFi ScanIP address WiFi test
Disable WiFi function
WiFi Security Settings
TKIP
1234567890
64 bits(10 hex digits)
Enable WiFi function
SSID
Security mode
WEP Encryption
WEP Key
WEA Encryption
WPA-PSK KEY
Save & Apply WiFi ScanIP address WiFi test
Disable WiFi function
12345678
WiFi Security Settings
wifi-test
Choose the wireless AP and key in the encryption key, click on the “Wi-Fi
test’’ button. If the test has succeeded, please press “Save & Apply’’ and
go to the next step.
Please do not unplug the Ethernet cable during the Wi-Fi test. If the test
has failed, please go back to the step 5.2.
5.1 Web Configure
5.3 Wireless Connection Settings
Remove the
Ethernet cable
Enable SD card recording.
Always Recording
When disk space full
SD-Card Status SD-Card Removed
Save & Apply
Schedule Recording
Circular recording
Stop recording
Standby
SD-Card Record Setting
→SD Card Record Settings on the Web
configuration page. Then select “schedule
recording” and the SD card recording will
be operational right after saving.
SD Card Playback. Right Click on the
selected camera on the camera list,
then choose the SD card playback.
What should I do if I have forgotten the password or the ID/Password card is missing?
Please press the Reset button for five seconds. The camera will reset to the factory default
settings. The default video-play password is ipcam (lowercase).
What should I do if I cannot see the video remotely?
The red LED of the camera should be remain on when the camera is connected to the Internet.
If the red LED is blinking, please double check the network connection and settings again.
I can see the video from a remote location, but the video quality is not satisfying and sometimes
the video disconnects and reconnects by itself.
It’s probably due to the poor Internet bandwidth (internet speed), which might be not good
enough.
You may try to apply for a better Internet connection from your Internet Service Provider or
reduce the bandwidth setting of the camera.
What is the default admin user name/password?
Default admin user name: admin
Default admin password: (leave blank)
Please refer to the following website to download the latest CamView software.
www.starvedia.com/download.html
Q1
Q2
Q3
Q4
Q5
Ans
Ans
Ans
Ans
Ans
Where to download the latest camView software?
[ FRONT ]
[ BACK ]
[ TOP ]
[ BOTTOM ]
