StarTech.com USB2VGAE Manual de usuario
USB2VGAE
USB 2.0 to VGA Video Display
Graphics Adapter
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital de-
vice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver•
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected
names and/or symbols of third-party companies not related in any way to StarTech.com. Where
they occur these references are for illustrative purposes only and do not represent an endorse-
ment of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. Regardless of any direct acknowl-
edgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all
trademarks, registered trademarks, service marks, and other protected names and/or symbols
contained in this manual and related documents are the property of their respective holders.
Instruction Manual
i
Instruction Manual
Table of Contents
Introduction ................................................................................... 1
Features ......................................................................................1
Package Contents .......................................................................1
System Requirements .................................................................1
Installation...................................................................................... 2
Quick Installation .........................................................................2
Windows CE Installation..............................................................2
Windows CE Un-Installation........................................................3
Configuration................................................................................. 3
Display Utility ...............................................................................3
Support Modes............................................................................3
Support Resolutions....................................................................4
USB-Graphics Card (Extended) .................................................4
Mirror ..........................................................................................5
USB-Graphics Card (Off) ............................................................5
Display Properties of the USB2VGAE.......................................... 6
Virtually Repositioning Your Displays ......................................... 7
Appendix ........................................................................................ 8
Frequently Asked Questions........................................................8
Troubleshooting Tips....................................................................9
Technical Support ......................................................................... 10
Warranty Information .................................................................... 10
Instruction Manual
1
Introduction
Thank you for purchasing a StarTech.com USB2VGAE USB 2.0 to VGA
Video Display Graphics Adapter. This innovative device allows you to
easily add a second display without installing a new video card, while
running resolutions of up to 1280x1024.
This compact USB to VGA solution supports Windows CE 5.0 and is ideal
for mobile or custom installs using Windows CE.
Features
No power adapter required and easy to install•
Supports resolutions of up to 1280x1024•
Supports Windows 2000/XP/Vista™ and Windows CE 5.0•
Works with desktop and notebook computers•
Package Contents
1 x USB to VGA adapter•
1 x Driver/Manual CD•
1 x User Manual•
System Requirements
Pentium 4/Celeron family or AMD K6/Athlon/Duron family with 1.5GHz•
256MB RAM or higher•
An available USB 2.0 port (with USB 2.0 host capability - USB 1.1 will•
suffice, however operation will be limited)
Windows 2000 SP4, Windows XP SP2 and Windows Vista™•
Instruction Manual
2
Installation
Quick Installation
Follow these steps to quickly install your new USB 2.0 Graphics Card:
Note: Do not plug the USB 2.0 Graphics Card into the system
before the driver is finished installing.
Insert the driver/manual CD and follow the instructions.1.
Turn on your second monitor and connect it to the adapter.2.
Connect the adapter to an available USB 2.0 port.3.
Once finished, you should see the extended display on the second4.
monitor.
Windows CE Installation
Copy the file1. trigger.cab (located on your software CD) to a USB 2.0
Flash drive.
Plug the USB 2.0 Flash drive into your device and open the2. trigger.cab
file.
Click3. Yes to continue the installation.
Choose4. Device to install the USB 2.0 VGA on Windows CE, then click
Install to complete the installation.
Connect the external display device to the VGA connector (DB15) of5.
the USB2VGAE adapter and turn the display power on. Then, connect
the USB2VGAE to your smart phone or PDA**. Your mobile device’s
display should now be visible on your external display device.
**Please note that the USB port on the Windows CE device must offer
USB 2.0 Host capability. USB 1.1 can be used, but will not deliver the
same performance as USB 2.0.
Instruction Manual
3
Windows CE Un-Installation
Disconnect the USB 2.0 Graphics card from your smart phone or PDA.1.
Select Remove Programs from the Settings menu.
Select2. MCT Trigger USB 2.0 VGA for Win Mobile, then click Remove.
Select3. Yes to remove the program and complete the un-installation
process.
Conguration
Display Utility
After the driver is installed, a utility will appear in the lower right taskbar.
This utility allows you to quickly change the settings and resolution of your
USB 2.0 Graphics Card. Access the menu by right clicking on the icon.
Support Modes
Primary1.
Extended2.
Mirror3.
Instruction Manual
4
Support Resolutions
Aspect Ratio Resolution Color Quality
5:4 1280 x 1024 16,32 bit
4:3 1024 x 768 16,32 bit
4:3 800 x 600 16,32 bit
4:3 640 x 480 16,32 bit
Note: 1280 x 768 is the ideal resolution for viewing DVDs.
USB-Graphics Card (Primary)
To make the USB 2.0 Graphics Card the main display adapter in the
system. The system’s main display (monitor) will automatically switch to
being the secondary display adapter and act as the extended desktop.
You can disable the other utility (usually found in the same toolbar located
on the bottom right hand corner) to make this function work properly.
Note: The Primary Function may disable the main display.
Instruction Manual
5
USB-Graphics Card (Extended)
By default, USB2VGAE will extend your Windows desktop.You can
change the relative position of this extension under the Display Proper-
ties (Go to Control Panel -> double click on the Display and select the
Settings tab).
Note: Playback suggestion: Media Player Classic software on Windows
Vista™.
Mirror
Your USB 2.0 Graphics Card will mirror your Windows desktop. You can
see the same desktop image in both monitors.
USB-Graphics Card (O)
This option disables the USB2VGAE on the system.
Instruction Manual
6
Display Properties of the USB2VGAE
To access the Display Properties for the USB2VGAE, go to Control Panel
and double click on the Display icon. Select the Settings tab.
Click on the Display pull-down menu and select the Default Monitor on
USB 2.0 Graphics Card-Extend. Then, click Extend my Windows desktop
onto this monitor. From here, you can change the resolution and color
depth as desired. Click OK to apply the settings.You can also make these
changes using the USB 2.0 Graphics Card utility.
Instruction Manual
7
Virtually Repositioning Your Displays
On the Settings tab of your Display Properties, click and drag the appro-
priate monitor icon (labeled 1 or 2) to the desired position. For example,
the secondary display can be dragged to the left of the primary display, al-
lowing it to be virtually on the left. Click OK or Apply to save the changes.
To make sure the USB2VGAE has been installed successfully:
Right-click on1. My Computer and select Manage, to open the Computer
Management window.
In the left pane, click on2. Device Manager. In the right pane, double-
click on Display adapters. Here, you will see two options:
USB2.0 Graphics Card- Extend•
USB2.0 Graphics Card- Mirror•
Plug-in the USB2VGAE adapter. Double-click Universal Serial Bus con-
trollers, where you will see:
USB2.0 Graphics Card.•
Tabla de contenidos
Otros manuales de Adaptador de StarTech.com
StarTech.com
StarTech.com CDP2HVGUASPD Manual de usuario
StarTech.com
StarTech.com USB32HD2 Manual de usuario
StarTech.com
StarTech.com PCI100MMSC Manual de usuario
StarTech.com
StarTech.com DKT30CDVPD Manual de usuario
StarTech.com
StarTech.com USBBT1EDR2 Manual de usuario
StarTech.com
StarTech.com USB31GEHD Manual de usuario
StarTech.com
StarTech.com PCIVGA7 Manual de usuario
StarTech.com
StarTech.com USB511WB Manual
StarTech.com
StarTech.com 8STICUSB232SM3 Manual de usuario
StarTech.com
StarTech.com Thunderbolt TB310G Manual de usuario
StarTech.com
StarTech.com PCI220USB Manual de usuario
StarTech.com
StarTech.com ICUSB2321284 Manual de usuario
StarTech.com
StarTech.com USB32HD2 Manual de usuario
StarTech.com
StarTech.com ICUSB2324852 Manual de usuario
StarTech.com
StarTech.com SP122DP2DVI Manual de usuario
StarTech.com
StarTech.com DKT30CSDHPD3 Manual de usuario
StarTech.com
StarTech.com USB3S2ESATA Manual de usuario
StarTech.com
StarTech.com PEX433WAC11 Manual de usuario
StarTech.com
StarTech.com USB32VGAV Manual de usuario
StarTech.com
StarTech.com DKT30CHV Manual de usuario
