ST STM32MP157D-EV1 Manual de usuario
Introduction
The STM32MP157F-EV1 and STM32MP157D-EV1 Evaluation boards (STM32MP157x-EV1) are designed as complete
demonstration and development platforms for STMicroelectronics Arm®-based dual Cortex®‑A7 32 bits and Cortex®‑M4 32
bits MPUs in the STM32MP1 Series. They leverage the capabilities of increased-frequency 800 MHz STM32MP1 Series
microprocessors for the user to develop applications, using STM32 MPU OpenSTLinux Distribution software for the main
processor, and STM32CubeMP1 software for the co-processor. They include an ST-LINK embedded debug tool, LEDs, push-
buttons, one joystick, 1-Gbps Ethernet, CAN FD, one USB OTG Micro-AB connector, four USB Host Type-A connectors, LCD
display with touch panel, camera, stereo headset jack with analog microphone input, four digital microphones, one SPDIF
Rx/Tx, smartcard, microSD™ card, and eMMC, NOR and NAND Flash memories.
STM32MP157x-EV1, shown in Figure 1 and Figure 2, is used as the reference design for user application development,
although it is not considered as final application.
To expand the functionality of the STM32MP157F-EV1 and STM32MP157D-EV1 Evaluation boards, two GPIO expansion
connectors are also available for motor control and Raspberry Pi® shields.
An ST-LINK/V2-1 is integrated on the board, as embedded in-circuit debugger and programmer for the STM32 MPU and the
USB Virtual COM port bridge.
Figure 1. STM32MP157x-EV1 top view Figure 2. STM32MP157x-EV1 bottom view
Pictures are not contractual.
Evaluation boards with increased-frequency 800 MHz STM32MP157 MPUs
UM2648
User manual
UM2648 - Rev 2 - November 2020
For further information contact your local STMicroelectronics sales office. www.st.com
1Features
• STM32MP157 Arm®-based dual Cortex®‑A7 800 MHz 32 bits + Cortex®‑M4 32 bits MPU in LFBGA448
package
• ST PMIC STPMIC1
• 2 × 4-Gbit DDR3L, 16 bits, 533 MHz
• 2 × 512-Mbit Quad-SPI Flash memory
• 32-Gbit eMMC v5.0
• 8-Gbit SLC NAND, 8 bits, 8-bit ECC, 4-KB PS
• 1-Gbit/s Ethernet (RGMII) compliant with IEEE-802.3ab
• USB Host 4-port hub
• USB OTG HS
• CAN FD
•5.5" TFT 720×1280 pixels with LED backlight, MIPI DSISM interface, and capacitive touch panel
• SAI audio codec
• 5-megapixel, 8-bit camera
• 4 × ST-MEMS digital microphones
• Smartcard
• microSD™ card
• 2 user LEDs
• 2 user and reset push-buttons, 1 wake-up button
• 4-direction joystick with selection button
• 5 V / 4 A power supply
• Board connectors:
– Ethernet RJ45
– 4 × USB Host Type-A
– USB OTG Micro-AB
– SPDIF RCA input and output
– CAN FD
– Stereo headset jack including analog microphone input
– Audio jack for external speakers
– Motor control
– External I2C
– LTDC
– Trace, JTAG, RS-232
– GPIO expansion connector (Raspberry Pi® shields capability)
– MEMS-microphone daughterboard expansion connector
• On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration capability: Virtual COM port and
debug port
•STM32CubeMP1 and full mainline open-source Linux® STM32 MPU OpenSTLinux Distribution (such as
STM32MP1Starter) software and examples
• Support of a wide choice of Integrated Development Environments (IDEs) including IAR Embedded
Workbench®, MDK-ARM, and STM32CubeIDE
STM32 Arm Cortex MPUs are based on the Arm® Cortex®-A and Cortex®-M processors.
Note: Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.
UM2648
Features
UM2648 - Rev 2 page 2/61
2Ordering information
To order an STM32MP157 Evaluation board, refer to Table 1. Additional information is available from the
datasheet and reference manual of the target STM32.
Table 1. List of available products
Order code Board reference Target STM32 Differentiating feature
STM32MP157D-EV1 • MB1262: mother board
• MB1263: MPU subsystem daughterboard
• MB1230: DSI display board
• MB1379: camera board
STM32MP157DAA1 Basic security
STM32MP157F-EV1 STM32MP157FAA1 Secure Boot and
cryptography
2.1 Codification
The meaning of the codification is explained in Table 2.
Table 2. Codification explanation
STM32MP1XXY-EVZ Description Example: STM32MP157F-EV1
STM32MP1 MPU series in STM32 Arm Cortex MPUs STM32MP1 Series
XX MPU product line in the series STM32MP157
Y
Options:
• D: basic security, 800 MHz increased frequency
• F: Secure Boot, cryptography hardware, 800 MHz
increased frequency
Secure Boot, cryptography
hardware, 800 MHz increased
frequency
EVZ Evaluation board configuration
• EV1: with PMIC PMIC
UM2648
Ordering information
UM2648 - Rev 2 page 3/61
3Development environment
3.1 System requirements
• Windows® OS (7, 8, or 10), Linux® 64-bit, or macOS®
• USB Type-C® to Type-A cable
• USB Type-A or USB Type-C® to Micro-B cable
• USB Type-A or USB Type-C® to Micro-AB cable
Note: macOS® is a trademark of Apple Inc. registered in the U.S. and other countries.
All other trademarks are the property of their respective owners.
3.2 Development toolchains
• IAR Systems - IAR Embedded Workbench®(1)
• Keil® - MDK-ARM(1)
• STMicroelectronics - STM32CubeIDE
• GCC
1. On Windows® only.
3.3 Demonstration software
The STM32 MPU OpenSTLinux Distribution and STM32CubeMP1 base demonstration software is preloaded in
the microSD™ for easy demonstration of the device peripherals in standalone mode. The latest versions of the
demonstration source code and associated documentation can be downloaded from www.st.com.
UM2648
Development environment
UM2648 - Rev 2 page 4/61
4Conventions
Table 3 provides the conventions used for the ON and OFF settings in the present document.
Table 3. ON/OFF convention
Convention Definition
Jumper JPx ON Jumper fitted
Jumper JPx OFF Jumper not fitted
Jumper JPx [1-2] Jumper fitted between Pin 1 and Pin 2
Solder bridge SBx ON SBx connections closed by 0 Ω resistor
Solder bridge SBx OFF SBx connections left open
Resistor Rx ON Resistor soldered
Resistor Rx OFF Resistor not soldered
UM2648
Conventions
UM2648 - Rev 2 page 5/61
5Delivery recommendations
Before the first use, make sure that no damage occurred to the board during shipment and no socketed
components are loose in their sockets or fallen into the plastic bag.
In particular, pay attention to the following components:
1. MB1263 daughterboard connected to the MB1262 mother board
2. microSD card in its MB1263/CN9 receptacle
3. LCD MB1230 daughterboard in MB1262/CN19 DSI connector, and screw, spacer and nut are in place
4. Camera module MB1379 board in MB1262/CN7 connector, and screw, spacer and nut are in place
For product information related to the STM32MP157 microprocessors, visit the www.st.com website.
UM2648
Delivery recommendations
UM2648 - Rev 2 page 6/61
6Hardware layout and configuration
The STM32MP157x-EV1 Evaluation board is designed around the STM32MP157xAA1 target microprocessor in
LFBGA 448-pin package. Figure 3 illustrates the STM32MP157x-EV1 hardware block diagram. Figure 4 shows
the location of main components on the Evaluation board.
UM2648
Hardware layout and configuration
UM2648 - Rev 2 page 7/61
Figure 3. STM32MP157x-EV1 hardware block diagram
STM32MP157xAAx
RTC
32 kHz crystal
Capacitive
touch screen
USB OTG Micro-AB USB
OTG HS
5.5" TFT 720x1280
USB
Host HS
USB Hub
4x USB Type-A
microSD™ card
connector
SDMMC
HSI
I2C
GPIO
2 user LEDs
2 user buttons
1 reset button
Smartcard
connector
Smartcard
SAI Audio codec
STPMIC1
5V_VIN
24 MHz crystal
GPIO 40-pin
connector
GPIOs
DDR3L DDR
LTDC LTDC connector
DSI
eMMC SDMMC
NAND FMC
Quad-SPI NOR
Flash Quad-SPI
Gigabit Ethernet RGMII DFSDM MEMS microphones
SPDIF
Tx/Rx SPDIF Tx/Rx
DCMI Camera
CAN FD
CAN FD connector
UART
RS-232 DB9
connector
JTAG/
SWD
ST-LINK/V2-1
USB Micro-B
Motor-control
connector
Shared
GPIOs
I2C
ADC/DAC ADC/DAC
connector
MICTOR-38
connector ETM
JTAG connector
Wake-up button
MFX I/O expander
Joystick
Stereo Jack
Line Out / MIC_IN
I2CI2C_EXT connector
UM2648
Hardware layout and configuration
UM2648 - Rev 2 page 8/61
Table 4. STM32MP157x-EV1 overview
Position Description
1 MB1262 mother board
2 MB1263 daughterboard
3MB1230 DSI (MIPI® standard) 720p display
4 MB1379 daughterboard camera
5microSD™ card
Table 5. MB1263 daughterboard overview
Position Description Position Description
50 (B1) Reset button 59 (CN1) MB1263 power 5 V-3 A
51 (LD2) User LED (red) 60 (SW1) Boot mode selection
52 (B2) User button (PA13) 61 (U3) PMIC (STPMIC1A)
53 (LD3) User LED (green) 62 (LD6) ST-LINK LED (bicolor)
54 (B3) User button (PA14) 63 (CN4) USB Micro-B (ST-LINK/V2-1)
55 (LD5) User LED (blue) 64 (U4) STM32MP157xAA1 LFBGA448
56 (LD4) User LED (orange) 65 (U5) eMMC
57 (B4) Wake-up button 66 (U6/U7) 2 x DDR3L 16 bits
58 (LD1) Power LED (green) 67 (µSD)microSD™ 3.0 card (back side slot)
Table 6. MB1262 mother board overview
Position Description Position Description
10 (CN3) Ethernet 11 (CN8) Microphone MEMS daughterboard connector
12 (CN4) Speaker audio output 13 (CN5) Headset audio output
14 (U8) Audio codec (Wolfson WM8994) 15 (CN1) SPDIF RX
16 (CN2) SPDIF TX 17 (U5) Smartcard (back side slot)
18 (LD1) Ethernet LED (green) 19 (CN6) Ethernet daughterboard connector
20 (U10) Trace connector 21 (CN11)LTDC LCD TFT display controller (STM32
specific) connector
22 (CN12) RS-232 (UART4) 23 (CN13) External E2P connector
24 (CN16) USB Micro-AB (USB OTG) 25 (LD2) USB OTG LED (green)
26 (LD3) USB Type-A port LED (red) 27 (CN17) MFX header 4 pins
28 (CN14) JTAG connector 29 (CN15) CAN FD
30 (CN18) 2 USB Type-A port (host) 31 (CN20) 2 USB Type-A port (host)
32 (B2) Reset button 33 (B1) Joystick
34 (CN22) Motor control connector 35 (CN21) GPIO expansion connector
4 (CN7) Camera sensor connector - -
UM2648
Hardware layout and configuration
UM2648 - Rev 2 page 10/61
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Placa madre de ST
ST
ST STLINK-V3SET Manual de usuario
ST
ST STEVAL-IHM031V1 Manual de usuario
ST
ST NUCLEO-WL55JC STM32WL Manual de usuario
ST
ST STM32H753I-EVAL Manual de usuario
ST
ST X-NUCLEO-NFC03A1 Manual de usuario
ST
ST STEVAL-IHM011V1 Manual de usuario
ST
ST UM1789 Manual de usuario
ST
ST NUCLEO-F411RE Manual
ST
ST STM32L476G-EVAL Manual de usuario
ST
ST STEVAL-L6982CDR Manual de usuario
ST
ST X-NUCLEO-CCA02M1 Manual de usuario
ST
ST STEVAL-ISW001V1 Manual de usuario
ST
ST L9678-S-EVB Manual de usuario
ST
ST STM32439I-EVAL Manual de usuario
ST
ST STM32F779I-EVAL Manual de usuario
ST
ST STM32 Nucleo Instrucciones de instalación y funcionamiento
ST
ST AEK-POW-LDOV01J Manual de usuario
ST
ST Contiki6LP Manual de usuario
ST
ST STM32MP157F-EV1 Manual de usuario
ST
ST UM1461 Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
