ST STEVAL-IDB007V Series Manual de usuario

Introduction

The STEVAL-IDB007Vx (STEVAL-IDB007V1/STEVAL-IDB007V2) is an evaluation board based on BlueNRG-1 (QFN32

package).

The STEVAL-IDB008Vx (STEVAL-IDB008V1/STEVAL-IDB008V2) is an evaluation board based on BlueNRG-2 (QFN32

package).

The STEVAL-IDB009Vx (STEVAL-IDB009V1) is an evaluation board based on BlueNRG-2 (QFN48 package).

BlueNRG-1 (QFN32 package) and BlueNRG-2 (QFN32 and QFN48 packages) are low power Bluetooth® smart systems-on-

chip compliant with the Bluetooth® specification and support master, slave and simultaneous master-and-slave roles.

The document content is valid for the STEVAL-IDB007Vx, STEVAL-IDB008Vx and STEVAL-IDB009Vx platforms. Any specific

difference is highlighted whenever it is needed.

Getting started with STEVAL-IDB007Vx, STEVAL-IDB008Vx and

STEVAL-IDB009Vx evaluation boards

UM2094

User manual

UM2094 - Rev 5 - November 2018

For further information contact your local STMicroelectronics sales office.

www.st.com

Downloaded from Arrow.com.

1Development platforms

Figure 1. STEVAL-IDB007V1 development platform

Figure 2. STEVAL-IDB007V2 development platform

Figure 3. STEVAL-IDB008V1 development platform

UM2094

Development platforms

UM2094 - Rev 5 page 2/14

Downloaded from Arrow.com.Downloaded from Arrow.com.

Figure 4. STEVAL-IDB008V2 development platform

Figure 5. STEVAL-IDB009V1 development platform

UM2094

Development platforms

UM2094 - Rev 5 page 3/14

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

2Acronyms and abbreviations

Table 1. List of acronyms

Acronym Description

BLE Bluetooth low energy

DK Development kit

SW Software

USB Universal serial bus

UM2094

Acronyms and abbreviations

UM2094 - Rev 5 page 4/14

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

3Getting started

The evaluation board is preprogrammed with sensor profile firmware (BLE_SensorDemo.hex) which allows to set

and establish a connection with a smartphone (iOS or Android) running a BlueNRG sensor application which

works with the sensor profile firmware running on the STEVAL-IDB007Vx, STEVAL-IDB008Vx or STEVAL-

IBD009Vx evaluation board.

The sensor profile firmware implements a proprietary Bluetooth profile which exposes two services: acceleration

and environmental service.

The acceleration service contains the following characteristics:

• Acceleration: it gives the current value of the acceleration detected by the MEMS sensor on the evaluation

board.

• Free fall characteristic: it allows detection of free-fall condition by the LSM6DS3 MEMS sensor on the

evaluation board (the condition is detected if the acceleration on the 3 axes is near zero for a certain amount

of time).

The environmental service contains characteristics that expose data from some environmental sensors, such as

temperature sensors.

3.1 Powering up the evaluation board running the sensor profile firmware

(peripheral role)

Two power options are available:

•Batteries - To power the selected evaluation board using batteries, 2 AAA batteries must be inserted into

the battery holder at the rear of the board, and jumper JP1 set to position 2-3 and jumper JP2 set to position

1-2 (Figure 6. Board power options).

•USB - To power the selected evaluation board through USB, jumper JP1 must be in position 1-2 and jumper

JP2 set to position 2-3 (Figure 6. Board power options ). Connect a USB cable to the micro-USB connector

(Figure 6. Board power options) and to a PC USB port.

Once powered, the evaluation board sensor profile firmware starts advertising, waiting for a smartphone to

connect to it.

UM2094

Getting started

UM2094 - Rev 5 page 5/14

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Figure 6. Board power options

3.2 Install the BlueNRG app for smartphones (central role)

• Two versions (Android and iOS) of the smartphone sensor application are available for download on the

specific web pages (Table 2. Reference information Android & iOS SensorApp).

• Install the smartphone SensorApp application on the selected smartphone.

3.3 Run BlueNRG app for smartphones

• Launch the BlueNRG SensorApp application on the smartphone

• It starts scanning for the BlueNRG sensor peripheral. A device called “BlueNRG” appears on the screen (this

is the STEVAL-IDB007Vx, STEVAL-IDB008Vx or STEVAL-IDB009Vx running the sensor profile firmware)

• Tap on the BlueNRG name to connect to the selected platform running the sensor profile firmware. The

BlueNRG SensorApp application enables notifications on the acceleration characteristic and displays the

received value on the screen.

UM2094

Install the BlueNRG app for smartphones (central role)

UM2094 - Rev 5 page 6/14

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Figure 7. Smartphone BlueNRG SensorApp acceleration notification

• Data from environmental sensors are also periodically read and displayed.

Figure 8. Smartphone BlueNRG SensorApp RSSI notifications

UM2094

Run BlueNRG app for smartphones

UM2094 - Rev 5 page 7/14

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

4Software demonstration applications

• In order to develop a software application for the STEVAL-IDB007Vx, STEVAL-IDB008Vx or STEVAL-

IDB009Vx evaluation board, it is recommended to start with the reference demonstration applications

provided within the BlueNRG-1_2 DK SW package for BlueNRG-1, BlueNRG-2 BLE stack v2.x family

(STSW-BLUENRG1-DK) available on the STEVAL-IDB007Vx, STEVAL-IDB008Vx, STEVAL-IDB009Vx web

pages, or the BlueNRG-1_V1 DK SW package for BlueNRG-1 BLE stack v1.x family (STSW-BNRG_V1-

DK), available on the STEVAL-IDB007Vx web page.

• Unzip the file, launch the related installer and follow installation steps.

• Wait for the package installation to complete.

• The Projects folder in DK SW package contains the available demonstration applications, IAR projects,

sources and header files.

• IAR Embedded Workbench for ARM (EWARM) tool is needed for building and downloading software

applications running on the BlueNRG-1, BlueNRG-2 microcontrollers.

Note: For a description of the available BlueNRG-1, BlueNRG-2 demonstration applications and supported platforms,

refer to BlueNRG-1, BlueNRG-2 development kits user manual available on the related web page. The

BLE_SensorDemo.hex prebuilt binary images for BlueNRG-1, BlueNRG-2 platforms are also provided within the

DK software package, in the Firmware folder.

Keil MDK-ARM and Atollic TrueStudio for ARM (GCC) toolchains projects are also available.

UM2094

Software demonstration applications

UM2094 - Rev 5 page 8/14

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

5References

Table 2. Reference information

What Where Description

BlueNRG-1 Bluetooth Low

Energy wireless System on

Chip

BlueNRG-1 BlueNRG-1 device web page

BlueNRG-2 Bluetooth Low

Energy wireless System on

Chip

BlueNRG-2 BlueNRG-2 device web page

Bluetooth Low Energy

Specification

https://www.bluetooth.org/en-us/specification/

adopted-specifications

Bluetooth Low Energy specification web

page

Smartphone Android 4.3

Sensor App

https://play.google.com/store/apps/details?

id=com.st.blunrg Android 4.3 BlueNRG Sensor App web page

Smartphone IoS Sensor App https://itunes.apple.com/us/app/bluenrg/

id705873549?l=it&ls=1&mt=8 IoS BlueNRG Sensor App web page

STSW-BLUENRG1-DK

STEVAL-IDB007V1, STEVAL-IDB007V2,

STEVAL-IDB008V1, STEVAL-IDB008V2 and

STEVAL-IDB009V1 web pages, Tools and

Software section

BlueNRG-1_2 DK SW package for

BlueNRG_1, BlueNRG-2 BLE stack v2.x

family, with reference demonstration

applications

STSW-BNRG_V1-DK STEVAL-IDB007V1 web page, Tools and

Software section

BlueNRG-1_V1 DK SW package for

BlueNRG-1 BLE stack v1.x family, with

reference demonstration applications

STEVAL-IDB007V1 BlueNRG-1, Evaluation Tools section STEVAL-IDB007V1 platform web page

STEVAL-IDB007V2 BlueNRG-1, Evaluation Tools section STEVAL-IDB007V2 platform web page

STEVAL-IDB008V1 BlueNRG-2, Evaluation Tools section STEVAL-IDB008V1 platform web page

STEVAL-IDB008V2 BlueNRG-2, Evaluation Tools section STEVAL-IDB008V2 platform web page

STEVAL-IDB009V1 BlueNRG-2, Evaluation Tools section STEVAL-IDB009V1 platform web page

UM2071

STEVAL-IDB007V1, STEVAL-IDB007V2,

STEVAL-IDB008V1, STEVAL-IDB008V2 and

STEVAL-IDB009V1 web pages

BlueNRG-1, BlueNRG-2 Development Kits

User Manual

UM2094

References

UM2094 - Rev 5 page 9/14

Revision history

Table 3. Document revision history

Date Revision Changes

14-Jul-2016 1 Initial release.

19-Dec-2016 2 Updated STEVAL-IDB007V1 Bluetooth® low energy evaluation board on the cover page.

23-Oct-2017 3

Added: reference to STEVAL-IDB008V1 BlueNRG-2 evaluation platform, reference to BlueNRG-1_2

DK SW package for BLE stack v2.x family and reference to BlueNRG-1_V1 DK SW package for

BLE stack v1.x family.

02-May-2018 4 Updated Introduction.

Added references to STEVAL-ID007V2 and STEVAL-IDB008V2 evaluation platforms.

27-Nov-2018 5

Updated title and Introduction.

Added Section 1 Development platforms and references to the STEVAL-IDB009V1 evaluation

platform (BlueNRG-2 QFN48 package).

UM2094

UM2094 - Rev 5 page 10/14

Otros manuales para STEVAL-IDB007V Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de ST

ST STEVAL-SP1ML915 Manual de usuario

ST EVAL-TDA7803A Manual de usuario

ST STEVAL-WBC86TX Manual de usuario

ST STUSB03E Manual de usuario

ST STM32H757I-EVAL Manual de usuario

ST NUCLEO-L433RC-P Manual de usuario

ST STEVAL-IDB007V1 Manual de usuario

ST STM32G070RBT6 Manual de usuario

ST AEKD-USBTYPEC1 Manual de usuario

ST X-NUCLEO-IDB04A1 Manual de usuario

ST ST9 EPB Manual de usuario

ST UM1748 Manual de usuario

ST STM32746G-EVAL Manual de usuario

ST UM0969 Manual de usuario

ST STM32429I-EVAL Manual de usuario

ST STUSB02E Manual de usuario

ST EnFilm EFL1K0AF39 Manual de usuario

ST STEVAL-ISB042V1 Manual de usuario

ST UM2248 Manual de usuario

ST EVALCOMMBOARD Manual de usuario

ST STEVAL-OET001V1-LCP154DJF Manual de usuario

ST STEVAL-PCC010V1 Manual de usuario

ST STEVAL-IHP007V1 Manual de usuario

ST UM1509 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario