ST STM32L562E-DK Manual de usuario
Introduction
The STM32L562E-DK Discovery kit is designed as a complete demonstration and development platform for STMicroelectronics
Arm® Cortex®-M33 core-based STM32L562QEI6QU microcontroller with TrustZone®. It features 256 Kbytes of internal SRAM
and 512 Kbytes of internal Flash memory, one flexible memory controller (FMC) interface, one Octo-SPI memory interface, one
LCD-TFT controller, one RTC, up to 16 timers, one USB Type-C™ device FS port with UCPD controller, two SAI ports, four I²C
buses, six USART ports, three SPI, one CAN-FD port, one SDMMC interface, 2x 12-bit ADC, 2x 12-bit DAC, 2 low-power
comparators, 4 digital filters for sigma-delta modulation, touch-sensing capability, an embedded step down converter, and JTAG
and ETM debugging support.
STM32L562E-DK, shown in Figure 1, associated with the fan-out expansion board, is used as a reference design for user
application development, although it is not considered as the final application.
The full range of hardware features on the board helps the user to evaluate all the peripherals (USB, USART, digital
microphones, ADC and DAC, TFT LCD, Octo-SPI Flash memory device, microSD™ card, audio codec, joystick, user button,
Bluetooth® Low Energy, accelerometer and gyroscope) and to develop applications. Extension headers allow easy connection
of a daughterboard or wrapping board for a specific application.
An STLINK-V3E is integrated on the board, as embedded in-circuit debugger and programmer for the STM32 MCU and the
USB Virtual COM port bridge.
Figure 1. STM32L562E-DK Discovery kit (top view)
Picture is not contractual.
Discovery kit with STM32L562QE MCU
UM2617
User manual
UM2617 - Rev 2 - January 2020
For further information contact your local STMicroelectronics sales office. www.st.com
1Features
• STM32L562QEI6QU microcontroller featuring 512 Kbytes of Flash memory and 256 Kbytes of SRAM in
BGA132 package
• 1.54" 240 × 240 pixel-262K color TFT LCD module with parallel interface and touch-control panel
• USB Type-C™ Sink device FS
• On-board energy meter: 300 nA to 150 mA measurement range with a dedicated USB interface
• SAI Audio CODEC
• MEMS digital microphones
• 512-Mbit Octal-SPI Flash memory
•Bluetooth® V4.1 Low Energy module
• iNEMO 3D accelerometer and 3D gyroscope
• 2 user LEDs
• User and reset push-buttons
• Board connectors:
–USB Type-C™
–microSD™ card
– Stereo headset jack including analog microphone input
– JTAG debugger
– DPM dynamic-power measurement interface for external device
– STMod+ expansion connector with fan-out expansion board for Wi‑Fi®, Grove and mikroBUS™
compatible connectors
– Pmod™ expansion connector
– Audio MEMS daughterboard expansion connector
– ARDUINO® Uno V3 expansion connector
• Flexible power-supply options: ST-LINK, USB VBUS or external sources
• On-board STLINK-V3E debugger/programmer with USB re-enumeration capability: mass storage, Virtual
COM port, and debug port
• Comprehensive free software libraries and examples available with the STM32CubeL5 MCU Package
• Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil®, and
STM32CubeIDE
Note: Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.
UM2617
Features
UM2617 - Rev 2 page 2/61
2Ordering information
To order the STM32L562E-DK Discovery kit, refer to Table 1. Additional information is available from the
datasheet and reference manual of the target STM32.
Table 1. Ordering information
Order code Board references Target STM32
STM32L562E-DK • MB1373
• MB1280(1) STM32L562QEI6QU
1. Fan-out board.
2.1 Product marking
Evaluation tools marked as “ES” or “E” are not yet qualified and therefore not ready to be used as reference
design or in production. Any consequences deriving from such usage will not be at ST charge. In no event, ST will
be liable for any customer usage of these engineering sample tools as reference designs or in production.
“E” or “ES” marking examples of location:
• On the targeted STM32 that is soldered on the board (For an illustration of STM32 marking, refer to the
STM32 datasheet “Package information” paragraph at the www.st.com website).
• Next to the evaluation tool ordering part number that is stuck or silk-screen printed on the board.
Some boards feature a specific STM32 device version, which allows the operation of any bundled commercial
stack/library available. This STM32 device shows a "U" marking option at the end of the standard part number
and is not available for sales.
In order to use the same commercial stack in his application, a developer may need to purchase a part number
specific to this stack/library. The price of those part numbers includes the stack/library royalties.
2.2 Codification
The meaning of the codification is explained in Table 2. The order code is mentioned on a sticker placed on the
top side of the board.
Table 2. Codification explanation
STM32TTXXY-DK Description Example: STM32L562E-DK
STM32TT MCU series in STM32 32-bit Arm Cortex MCUs STM32L5 Series
XX MCU product line in the series STM32L562
YSTM32 Flash memory size:
• E for 512 Kbytes 512 Kbytes
UM2617
Ordering information
UM2617 - Rev 2 page 3/61
3Development environment
3.1 System requirements
• Windows® OS (7, 8 and 10), Linux® 64-bit, or macOS®
• USB Type-A to Micro-B cable
Note: macOS® is a trademark of Apple Inc. registered in the U.S. and other countries.
All other trademarks are the property of their respective owners.
3.2 Development toolchains
• IAR™ - EWARM (see note)
• Keil® - MDK-ARM (see note)
• STMicroelectronics - STM32CubeIDE
Note: On Windows® only.
3.3 Demonstration software
The demonstration software, included in the STM32Cube MCU Package corresponding to the on-board
microcontroller, is preloaded in the STM32 Flash memory for easy demonstration of the device peripherals in
standalone mode. The latest versions of the demonstration source code and associated documentation can be
downloaded from www.st.com.
UM2617
Development environment
UM2617 - Rev 2 page 4/61
4Conventions
Table 3 provides the conventions used for the ON and OFF settings in the present document.
Table 3. ON/OFF convention
Convention Definition
Jumper JPx ON Jumper fitted
Jumper JPx OFF Jumper not fitted
Jumper JPx [1-2] Jumper should be fitted between Pin 1 and Pin 2
Solder bridge SBx ON SBx connections closed by 0 Ω resistor
Solder bridge SBx OFF SBx connections left open
Resistor Rx ON Resistor soldered
Resistor Rx OFF Resistor not soldered
UM2617
Conventions
UM2617 - Rev 2 page 5/61
5Delivery recommendations
Before the first use, make sure that no damage occurred to the board during shipment and no socketed
components are not firmly fixed in their sockets or loose in the plastic bag.
UM2617
Delivery recommendations
UM2617 - Rev 2 page 6/61
6Hardware layout and configuration
The STM32L562E-DK Discovery kit is designed around the STM32L562QEI6QU target microcontroller. Figure 2
illustrates STM32L562QEI6QU connections with peripheral components. Figure 3 shows the location of the main
components on the top side of the Discovery board and Figure 4 shows the location of the main components on
the bottom side of the Discovery board.
Figure 2. Hardware block diagram
STM32L562QEI6QU
RTC
SWD
32 kHz crystal
STLINK-V3E
USB
STDC14
TAG
Multi-point
capacitive
touch screen
USB Type-C™
connector FS
USB FS
UCPD
FMC
LCD TFT connector
1.54" 240x240
Octal-
SPI
Octo-SPI Flash
512 KBytes
VCP
UART
ARDUINO® Uno
connectors
GPIOs
BLE V4.1
SPI1
microSD™
connector SDMMC
HSI
I2C1
GPIO User interface
2 LEDs
User Interface
RESET and USER
buttons
GPIO
SAI Audio DAC and
amplifier Stereo jack
Line out / Mic_IN
DFSDM
External STM
module. Up to 4
microphones
Switch
3V3 POWER
SUPPLY
1V8 POWER
SUPPLY
5V_SELECTION
3V3
1V8
Power consumption metering
3V3
Optional
16 MHz crystal
3D accelerometer
3D gyrometer
I2C1
I2C1
STMod+ connectors
GPIOs
Pmod™ connectors
GPIOs
UM2617
Hardware layout and configuration
UM2617 - Rev 2 page 7/61
Figure 3. STM32L562E-DK PCB layout (top view)
Figure 4. STM32L562E-DK PCB layout (bottom view)
UM2617
Hardware layout and configuration
UM2617 - Rev 2 page 8/61
6.1 Embedded STLINK-V3E
6.1.1 Description
There are two different ways to program and debug the onboard STM32 MCU:
• Using the embedded STLINK-V3E
• Using an external debug tool connected to CN8 STDC14/MIPI-10 connector
The STLINK-V3E facility for debugging and flashing is integrated into the STM32L562E-DK Discovery kit.
The STLINK-V3E makes the STM32L562E-DK Discovery kitArm® Mbed Enabled™.
The embedded STLINK-V3E supports only SWD and VCP for STM32 devices.
Features supported in STLINK-V3E:
• 5 V power supplied by the CN17 USB connector
• USB 2.0 high-speed-compatible interface
• JTAG and serial wire debugging (SWD) specific features:
– 3 to 3.6 V application voltage on the JTAG/SWD interface and 5V tolerant inputs
– JTAG
– SWD and serial viewer (SWV) communication
• Direct firmware update feature (DFU) (CN6)
• STDC14 (MIPI10) compatible connector (CN8)
• LD3 status LED (COM) which blinks during communication with the PC
• LD11 fault red LED (OC) alerting on USB overcurrent request
• 5 V / 500 mA output power supply capability (U47) with current limitation and LD11 LED
• 5 V power green LD12 LED (5V)
Table 4 describes the CN17 USB Micro-B connector pinout.
Table 4. CN17 USB Micro-B connector pinout
Pin Pin name Signal name STLINK-V3E STM32 pin Function
1 VBUS 5V_USB_CHGR - VBUS Power
2 DM USB_DEV_HS_CN_N PB14 DM
3 DP USB_DEV_HS_CN_P PB15 DP
4 ID - GND ID
5 GND GND GND GND
6.1.2 Drivers
Before connecting the STM32L562E-DK board to a Windows PC via USB, the user must install a driver for the
STLINK-V3E (not required for Windows 10). It is available on the www.st.com website.
In case the STM32L562E-DK board is connected to the PC before the driver is installed, some STM32L562E-DK
interfaces may be declared as “Unknown” in the PC device manager. In this case, the user must install the
dedicated driver files, and update the driver of the connected device from the device manager as shown in
Figure 5.
Note: Prefer using the USB Composite Device handle for a full recovery.
UM2617
Embedded STLINK-V3E
UM2617 - Rev 2 page 9/61
Figure 5. USB composite device
Note: 37xx:
• 374E for STLINK-V3E without bridges functions
• 374F for STLINK-V3E with bridges functions
6.1.3 STLINK-V3E firmware upgrade
The STLINK-V3E embeds a firmware upgrade mechanism for in-situ upgrades through the USB port. As the
firmware may evolve during the lifetime of the STLINK-V3E product (for example new functionalities, bug fixes,
support for new microcontroller families), it is recommended to visit the www.st.com website before starting to use
the STM32L562E-DK Discovery kit and periodically, to stay up-to-date with the latest firmware version.
6.1.4 Using an external debug tool to program and debug the onboard STM32
There are 2 basic ways to support an external debug tool:
1. Keep the embedded STLINK-V3E running. Power on the STLINK-V3E at first until the COM LED lights RED.
Then connect the external debug tool through CN8 STDC14/MIPI-10 debug connector.
2. Set the embedded STLINK-V3E in a high impedance state. When setting the jumper JP6 (STLK_RST) ON,
the embedded STLINK-V3E is in RESET state and all GPIOs are in high impedance. Then the user can
connect his external debug tool on the debug connector CN8.
Figure 6. Connecting an external debug tool to program the on-board STM32L5
UM2617
Embedded STLINK-V3E
UM2617 - Rev 2 page 10/61
Otros manuales para STM32L562E-DK
1
Tabla de contenidos
Otros manuales de Microcontrolador de ST
ST
ST STEVAL-L6982NDR Manual de usuario
ST
ST STEVAL-MKSBOX1V1 Manual de usuario
ST
ST EVLKST8500GH868 Manual de usuario
ST
ST ST7232A Manual de usuario
ST
ST STM32 Series Instrucciones de instalación y funcionamiento
ST
ST STM32L496 Series Instrucciones de instalación y funcionamiento
ST
ST STM32F401 Discovery Manual de usuario
ST
ST STM32WL55JC Manual de usuario
ST
ST STM32F207 series Manual de usuario
ST
ST STM32H747I-DISCO Manual de usuario
ST
ST UM2966 Manual de usuario
ST
ST STM8S Manual de usuario
ST
ST UM2708 Manual de usuario
ST
ST UM1870 Manual de usuario
ST
ST UM2135 Manual de usuario
ST
ST STM32F413 Series Manual de usuario
ST
ST STM32F205 series Manual del propietario
ST
ST STM32F0 Series Instrucciones de instalación y funcionamiento
ST
ST STM32MP135F-DK Manual de usuario
ST
ST STM32F423 Series Manual de usuario
Manuales populares de Microcontrolador de otras marcas
AMS
AMS AS7261 Demo Kit Manual de usuario
Novatek
Novatek NT6861 Manual de usuario
Espressif Systems
Espressif Systems ESP8266 SDK Guía de configuración
Nuvoton
Nuvoton ISD61S00 ChipCorder Guía
STMicrolectronics
STMicrolectronics ST7 Assembler Linker Manual de usuario
Texas Instruments
Texas Instruments Chipcon CC2420DK Manual de usuario
Lantronix
Lantronix Intrinsyc Open-Q 865XR SOM Manual de usuario
NEC
NEC 78GK0S/K 1+ Series Instrucciones de instalación y funcionamiento
Mikroe
Mikroe SEMITECH N-PLC Click Instrucciones de instalación y funcionamiento
Intel
Intel Agilex Manual de usuario
Cypress
Cypress CY4607 HX2VL Manual de usuario
DIGITAL-LOGIC
DIGITAL-LOGIC MICROSPACE Manual de usuario
Texas Instruments
Texas Instruments TMS320F2837 D Series Manual de usuario
CYPRES
CYPRES CY14NVSRAMKIT-001 Manual de usuario
Texas Instruments
Texas Instruments INA-DUAL-2AMP-EVM Manual de usuario
Espressif Systems
Espressif Systems ESP8266EX Instrucciones de funcionamiento
Abov
Abov AC33M8128L Manual de usuario
Laird
Laird BL654PA Manual de usuario