ST STM32L562E-DK Manual de usuario
Introduction
The STM32L562E-DK Discovery kit is designed as a complete demonstration and development platform for the
STMicroelectronics Arm® Cortex®-M33 core-based STM32L562QEI6Q microcontroller with TrustZone®. It features 256 Kbytes
of internal SRAM and 512 Kbytes of internal flash memory, one flexible memory controller (FMC) interface, one Octo‑SPI
memory interface, one TFT-LCD controller, one RTC, up to 16 timers, one USB Type-C® device FS port with UCPD controller,
two SAI ports, four I2C buses, six USART ports, three SPIs, one CAN‑FD port, one SDMMC interface, 2x 12-bit ADC, 2x 12-bit
DAC, two low-power comparators, four digital filters for sigma-delta modulation, touch-sensing capability, an embedded step-
down converter, and JTAG and ETM debugging support.
STM32L562E-DK, shown in Figure 1, associated with the fanout expansion board, is used as a reference design for user
application development, although it is not considered as the final application.
The full range of hardware features on the board helps the user to evaluate all the peripherals (USB, USART, digital
microphones, ADC and DAC, TFT LCD, Octo‑SPI flash memory device, microSD™ card, audio codec, joystick, user button,
Bluetooth® Low Energy, accelerometer and gyroscope) and to develop applications. Extension headers allow easy connection
of a daughterboard or wrapping board for a specific application.
An STLINK-V3E is integrated on the board, as an embedded in-circuit debugger and programmer for the STM32 MCU and the
USB Virtual COM port bridge.
Figure 1. STM32L562E-DK Discovery kit (top view)
Picture is not contractual.
Discovery kit with STM32L562QE MCU
UM2617
User manual
UM2617 - Rev 7 - October 2023
For further information contact your local STMicroelectronics sales office.
www.st.com
1 Features
• STM32L562QEI6Q microcontroller featuring 512 Kbytes of flash memory and 256 Kbytes of SRAM in a
BGA132 package
• 1.54" 240 × 240 pixel-262K color TFT-LCD module with a parallel interface and touch‑control panel
• USB Type-C® Sink device FS
• On-board energy meter: 300 nA to 150 mA measurement range with a dedicated USB interface
• SAI audio codec
• MEMS digital microphones
• 512-Mbit Octo‑SPI flash memory
•Bluetooth® Low Energy V4.1 module
• iNEMO 3D accelerometer and 3D gyroscope
• Two user LEDs
• User and reset push-buttons
• Board connectors:
–USB Type-C®
–microSD™ card
– Stereo headset jack including analog microphone input
– JTAG debugger
– DPM dynamic-power measurement interface for external device
– STMod+ expansion connector with fanout expansion board for Wi‑Fi®, Grove, and mikroBUS™
compatible connectors
– Pmod™ expansion connector
– Audio MEMS daughterboard expansion connector
– ARDUINO® Uno V3 expansion connector
• Flexible power-supply options: ST-LINK USB VBUS, USB connector, or external sources
• On-board STLINK-V3E debugger/programmer with USB re-enumeration capability: mass storage, Virtual
COM port, and debug port
• Comprehensive free software libraries and examples available with the STM32CubeL5 MCU Package
• Support of a wide choice of Integrated Development Environments (IDEs) including IAR Embedded
Workbench®, MDK-ARM, and STM32CubeIDE
Note: Arm and TrustZone are registered trademarks of Arm Limited (or its subsidiaries) in the US and/or elsewhere.
UM2617
Features
UM2617 - Rev 7 page 2/64
2 Ordering information
To order the STM32L562E-DK Discovery kit, refer to Table 1. Additional information is available from the
datasheet and reference manual of the target STM32.
Table 1. Ordering information
Order code Board references Target STM32
STM32L562E-DK • MB1373(1)
• MB1280(2) STM32L562QEI6Q
1. Main board.
2. Fanout board.
2.1 Codification
The meaning of the codification is explained in Table 2.
Table 2. Codification explanation
STM32XXYYZ-DK Description Example: STM32L562E-DK
XX MCU series in STM32 32-bit Arm Cortex MCUs STM32L5 series
YY MCU product line in the series STM32L562
ZSTM32 flash memory size:
• E for 512 Kbytes 512 Kbytes
DK Discovery kit Discovery kit
UM2617
Ordering information
UM2617 - Rev 7 page 3/64
3 Development environment
3.1 System requirements
•Multi‑OS support: Windows® 10, Linux® 64-bit, or macOS®
• USB Type-A or USB Type-C® to Micro-B cable
Note: macOS® is a trademark of Apple Inc., registered in the U.S. and other countries and regions.
Linux® is a registered trademark of Linus Torvalds.
Windows is a trademark of the Microsoft group of companies.
3.2 Development toolchains
•IAR Systems® - IAR Embedded Workbench®(1)
•Keil® - MDK-ARM(1)
• STMicroelectronics - STM32CubeIDE
1. On Windows® only.
3.3 Demonstration software
The demonstration software, included in the STM32Cube MCU Package corresponding to the on-board
microcontroller, is preloaded in the STM32 flash memory for easy demonstration of the device peripherals in
standalone mode. The latest versions of the demonstration source code and associated documentation can be
downloaded from www.st.com.
UM2617
Development environment
UM2617 - Rev 7 page 4/64
4 Conventions
Table 3 provides the conventions used for the ON and OFF settings in the present document.
Table 3. ON/OFF convention
Convention Definition
Jumper JPx ON Jumper fitted
Jumper JPx OFF Jumper not fitted
Jumper JPx [1-2] Jumper fitted between Pin 1 and Pin 2
Solder bridge SBx ON SBx connections closed by 0 Ω resistor
Solder bridge SBx OFF SBx connections left open
Resistor Rx ON Resistor soldered
Resistor Rx OFF Resistor not soldered
Capacitor Cx ON Capacitor soldered
Capacitor Cx OFF Capacitor not soldered
UM2617
Conventions
UM2617 - Rev 7 page 5/64
5 Delivery recommendations
Before the first use, check the board for any damage that might have occurred during shipment, and check that all
socketed components are firmly fixed in their sockets and that none is loose in the plastic bag.
UM2617
Delivery recommendations
UM2617 - Rev 7 page 6/64
6 Hardware layout and configuration
The STM32L562E-DK Discovery kit is designed around the STM32L562QEI6Q target microcontroller. Figure 2
illustrates STM32L562QEI6Q connections with peripheral components. Figure 3 shows the location of the main
components on the top side of the Discovery board. Figure 4 shows the location of the main components on the
bottom side of the Discovery board.
Figure 2. Hardware block diagram
DT52979V1
STM32L562QEI6Q
RTC
SWD
32 kHz crystal
STLINK-V3E
USB
STDC14
TAG
Multi-point capacitive
touch screen
USB Type-C®
connector FS
USB FS
UCPD
FMC
LCD TFT connector
1.54" 240x240
Octal-SPI
512 Kbytes Octo-SPI
flash memory
VCP
UART
ARDUINO® Uno
connectors
GPIOs
Bluetooth® Low
Energy V4.1
SPI1
microSD™ connector SDMMC
HSI
I2C1
GPIO User interface
2 LEDs
User Interface
RESET and USER
buttons
GPIO
SAI Audio DAC and
amplifier
Stereo jack
Line out / Mic_IN
DFSDM
External STM module.
Up to 4 microphones
Switch
3V3 power
supply
1V8 power
supply
5V_SELECTION
3V3
1V8
Power consumption metering
3V3
Optional
16 MHz crystal
3D accelerometer
3D gyrometer
I2C1
I2C1
STMod+ connectors
GPIOs
Pmod™ connectors
GPIOs
UM2617
Hardware layout and configuration
UM2617 - Rev 7 page 7/64
Figure 3. STM32L562E-DK PCB layout (top view)
DT52980V1
Audio Codec (U1) SD card interface
(CN1)
Octo-SPI (U6)
5V PWR source
(JP4)
STMod+
(CN3)
PmodTM (CN4)
ST-LINK LED (LD3)
TAG footprint (CN9)
STDC14 (CN8)
STM32L562QEI6Q (U7)
RESET button
(B1)
LEDs:
•
User green (LD10)
•
User red (LD9)
•
PM Test OK (LD4)
•
PM Out ON (LD5)
•
PM Error (LD6)
•
PM (LD7)
•
PM USB 5V error (LD8)
PM_Debug
(CN10)
External MEMS module
(CN2)
VDD 1V8/3V3 (JP3)
5V PWR
(LD12)
TCP: 5V_USB_C (LD2)
ARD-D13
(LD1)
VDD_MCU SEL:
VDD or DYN_OUT (SW1)
STLK_5V_OVC (LD11)
LCD 240x240
IDD (JP2)
USER button
(B2)
Bluetooth®
Low Energy
(U11)
Figure 4. STM32L562E-DK PCB layout (bottom view)
DT52981V1
USB Type-C® (CN15)
Arduino_A[0..5]
(CN19)
Arduino_PWR
(CN18)
STLINK STM32 (U25)
USB_STLINK (CN17)
Arduino_D[8..15]
(CN11)
3D ACC
3D GYRO
(U51)
External PM
measurement
(CN20)
STLK_NRST (JP6)
USB_C, DBn/SPI (JP5)
Arduino_D[0..7]
(CN12)
MEMS (U16)
Audio jack
(CN13)
LCD-CTP
connector
(CN14)
USB_PM
(CN16)
PM RESET
(B3)
PM_BOOT mode
(SW2)
UM2617
Hardware layout and configuration
UM2617 - Rev 7 page 8/64
6.1 Embedded STLINK-V3E
6.1.1 Description
There are two different ways to program and debug the onboard STM32 MCU:
• Using the embedded STLINK-V3E
• Using an external debug tool connected to the STDC14/MIPI10 connector (CN8)
The STLINK-V3E facility for debugging and flashing is integrated into the STM32L562E-DK Discovery kit.
The STLINK-V3E makes the STM32L562E-DK Discovery kitArm® Mbed Enabled™.
The embedded STLINK-V3E supports only SWD and VCP for STM32 devices.
Features supported in STLINK-V3E:
• 5 V power supplied by the USB connector (CN17)
• USB 2.0 high-speed-compatible interface
• JTAG and Serial Wire Debug (SWD) specific features:
– 3 to 3.6 V application voltage on the JTAG/SWD interface and 5 V tolerant inputs
– JTAG
– SWD and Serial Wire Viewer (SWV) communication
• STDC14 (MIPI10) compatible connector (CN8)
• COM status LED (LD3) which blinks during communication with the PC
• OC fault red LED (LD11) alerting on USB overcurrent request
• 5 V/500 mA output power supply capability (U47) with current limitation and LED (LD11)
• 5 V power green LED (LD12)
Table 4 describes the USB Micro-B connector (CN17) pinout.
Table 4. USB Micro-B connector (CN17) pinout
Pin Pin name Signal name STLINK-V3E STM32 pin Function
1 VBUS 5V_USB_CHGR - VBUS power
2 DM USB_DEV_HS_CN_N PB14 DM
3 DP USB_DEV_HS_CN_P PB15 DP
4 ID - GND ID
5 GND GND GND GND
6.1.2 Drivers
Before connecting the STM32L562E-DK board to a Windows PC via USB, the user must install a driver for
STLINK-V3E (not required since Windows® 10). It is available on the www.st.com website.
In case the STM32L562E-DK board is connected to the PC before the driver is installed, some STM32L562E-DK
interfaces might be declared as Unknown in the PC device manager. In this case, the user must install the
dedicated driver files, and update the driver of the connected device from the device manager as shown in
Figure 5.
Note: Prefer using the USB Composite Device handle for a full recovery.
UM2617
Embedded STLINK-V3E
UM2617 - Rev 7 page 9/64
Figure 5. USB composite device
Note: 37xx:
• 374E for STLINK-V3E without bridge functions
• 374F for STLINK-V3E with bridge functions
6.1.3 STLINK-V3E firmware upgrade
The STLINK-V3E embeds a firmware upgrade mechanism for in‑place upgrades through the USB port. The
firmware might evolve during the lifetime of the STLINK-V3E product (for example new functionalities, bug fixes,
support for new microcontroller families). Visit the www.st.com website before starting to use the STM32L562E-
DK Discovery kit and periodically, to stay up-to-date with the latest firmware version.
6.1.4 Using an external debug tool to program and debug the onboard STM32
Two basic ways to support an external debug tool:
1. Keep the embedded STLINK-V3E running. Power on the STLINK-V3E at first until the COM LED lights RED.
Then connect the external debug tool through the STDC14/MIPI10 debug connector (CN8).
2. Set the embedded STLINK-V3E in a high‑impedance state. When setting the jumper JP6 (STLK_RST) ON,
the embedded STLINK-V3E is in the RESET state and all GPIOs are in high impedance. Then the user can
connect the external debug tool to the debug connector (CN8).
Figure 6. Connecting an external debug tool to program the on-board STM32L5
DT52982V1
STDC14/
MIPI10
connector
(CN8)
ST-LINK
USB
(bottom side)
(CN17)
STLK_RST
(JP6)
ST-LINK
STM32
(bottom side)
(U25)
5V PWR source
(JP4 [1-2])
LCD 240x240 + CTP
TOP SIDEBOTTOM SIDE
5V PWR
(LD12)
UM2617
Embedded STLINK-V3E
UM2617 - Rev 7 page 10/64
Otros manuales para STM32L562E-DK
1
Tabla de contenidos
Otros manuales de Hardware de computadora de ST
ST
ST STM32U5 Manual de usuario
ST
ST STEVAL-IFP045V1 Manual de usuario
ST
ST STM32Cube Manual de usuario
ST
ST STA309A Manual de usuario
ST
ST X-NUCLEO-IDW01M1 Manual de usuario
ST
ST STM32Cube Manual de usuario
ST
ST X-NUCLEO-IHM09M2 Manual de usuario
ST
ST STEVAL-DPSG474 Manual de usuario
ST
ST STM32U5G9J-DK2 Manual de usuario
ST
ST PCC020V1 Manual de usuario
ST
ST UM0501 Manual de usuario
ST
ST STM8S-DISCOVERY Manual de usuario
ST
ST HTSSOP38 Manual de usuario
ST
ST MotionTL Manual de usuario
ST
ST X-NUCLEO-IHM02A1 Manual de usuario
ST
ST UPSD3212A Manual de usuario
ST
ST STEVAL-USBI2CFT Manual de usuario
ST
ST X-NUCLEO-IHM17M1 Manual de usuario
ST
ST STM32 Nucleo Manual de usuario
ST
ST STEVAL-STWINMA2 Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
