Spypoint LINK-MICRO-LTE Manual de usuario
v.1.8
LINK-MICRO-LTE AND
COMPARABLE*
QUICK START GUIDE
2
ENGLISH
IN THE BOX
1x LINK-MICRO-LTE camera
1x SIM card (preactivated and inserted in the camera)
1x Antenna holder
1x Installation strap
1x Quick Start Guide
NOTE
Memory card and batteries are sold separately.
User Manual, latest firmware, and FAQ available at:
www.spypoint.com/support.
COMPONENTS
qAntenna
wDetection lens
eMicroSD card slot
rLight sensor
tDelay light
yPhoto lens
uLED
iOFF/ON switch
oSTATUS light
aSIM card slot
sBattery compartment
dBattery holder
fSlot for installation strap
gDoor
hLocking latch
jCable lock hole
k12 V jack
lScrew-thread for standard
¼"-20 tripod mount
3
ENGLISH
q
w
e
f
h
g
j
r
t
y
u
i
o
a
s
d
k
l
4
ENGLISH
GETTING STARTED
CHOOSING A POWER SOURCE (3 OPTIONS)
• Alkaline or lithium AA batteries
• Rechargeable battery 12 V (#KIT-12V sold separately)
• Rechargeable battery pack 3,7 V (#LIT-10 sold separately)
NOTE
We recommend using the SPYPOINT #LIT-10
rechargeable lithium battery pack, sold separately.
FOR BEST RESULTS AND NO LEAKAGE
• Use only new alkaline or lithium batteries.
• Do not mix new and old batteries.
• Do not use rechargeable AA batteries
(their lower voltage can generate operational issues).
HOW TO INSTALL AA BATTERIES PROPERLY
• Unlock the latch and open the
LINK-MICRO-LTE door.
• Remove the battery compartment by
grasping it by the 2 small notches on
the side and pulling it out (see photo).
• Insert the AA batteries into the battery
holder following polarity (+) and (-)
indications.
• Place the battery holder back into the
battery compartment.
5
ENGLISH
INSTALLING A MICROSD CARD
The memory card is sold separately. You must first purchase
a class 10 microSD card between 2 GB and 32 GB of memory.
Before inserting the microSD card into your camera, it must be
formatted to ensure proper operations. Visit www.spypoint.com/
support if you need help to format your microSD card.
INSERTING YOUR MICROSD CARD
• Make sure the camera is turned OFF.
• Find the microSD card slot. It is located on
the left, above the battery compartment
(see photo).
• Insert a microSD card (up to 32 GB) in the
microSD card slot with the metal contacts
facing down.
• The card is inserted correctly when a click
is heard.
CLEAR THE ANTENNA
The camera comes with an antenna
mount that holds and protects the
antenna during shipping. You have
to remove it. This will allow you to move
and point your antenna in the desired
direction. Save and reuse the mount
to protect your antenna during future trips.
6
ENGLISH
ACTIVATE YOUR CAMERA
Before you can use your camera, you have to activate
it. To do so, you will need your activation code.
FINDING THE ACTIVATION CODE
The activation code is located inside the LINK-MICRO-LTE's
battery compartment.
To activate your camera, you have two choices: you can
either do it via the SPYPOINT app or via our website
www.spypoint.com.
Activation code
7
ENGLISH
SPYPOINT APP
If you choose to use the SPYPOINT app to activate
your device, follow these steps:
1. On Google PlayTM or the App StoreTM, search for “SPYPOINT”.
2. Download and install the app on your smartphone or tablet.
3. Start the app. Select “ACTIVATE A DEVICE”. In the list, select
“LINK-MICRO-LTE”then follow the steps to create an account.
4. When complete, a confirmation email with instructions on how
to finalize the creation of your account will be sent to you.
5. Log in to the SPYPOINT app using your email address
and password.
SPYPOINT.COM WEBSITE
If you choose to use our SPYPOINT website
to activate your device, follow these steps:
1. On the www.spypoint.com website, select “LOGIN” in the
top navigation menu. On the displayed “SPYPOINT” page,
select “REGISTER”, fill out the required fields, then log in.
2. Select the +sign on the far right of the page; in the list,
select “LINK-MICRO-LTE” then follow the steps.
3. When complete, a confirmation email with instructions on how
to finalize the creation of your account will be sent to you.
4. On the SPYPOINT website, log in to your account using your
email address and password.
8
ENGLISH
CHOOSING A PHOTO TRANSMISSION PLAN FOR YOUR CAMERA
Go to www.spypoint.com/en/spypoint-experience/plans
to read the latest oers and choose the plan that suits you.
CONFIGURING YOUR CAMERA
Both the SPYPOINT app and website let you congure all the
camera settings remotely. They also provide basic information
on your camera – such as: cellular signal strength, battery level,
and microSD card space used. This information is based upon
the latest connection with your camera.
New settings take eect every time the camera connects with
app or website.
Note that for 15 minutes after the camera is turned ON, it will
communicate with the server every time it takes a photo and will
also apply the settings you have chosen. Afterwards, it will com-
municate according to the default settings (transfer frequency/
rst transfer time) or those you chose to apply. Below are the
most basic settings you will congure.
CONFIGURATION: MAIN SETTINGS
Delay: Allows you to set the time interval between each detection
before the camera records the next photo or video.
Multi-shot: Allows you to set the number of photos per detection
(up to 2) with a 5-second delay between each photo.
Sensitivity: Allows you to set the detection sensitivity of the
camera.
Camera name: Allows you to name each owned camera.
9
ENGLISH
CELLULAR SETUP
First transfer time:Allows you to choose the time when the
camera makes its rst transfer of the day.
Transfer frequency:Allows you to choose the number of daily
transfers.
ADVANCED OPTIONS/CONFIGURATION
Schedule:Allows you to set the period of operation for each day
of the week. For a 24-hour operation mode, both the start and
stop times must be 12 AM.
NOTE
Camera transfers are set by default to 4-hour intervals determined
from the time you activated your camera. For example, if your
camera was activated at 1:42p.m., the next transfer will take
place at 5:42p.m.
STARTING YOUR CAMERA
1. Turn ON the camera.
2. The green STATUS light will ash while searching for a signal
(can take a few minutes).
3. The STATUS light will light up in one of the following 3 colors:
Red: Insucient signal
Orange: Acceptable signal
Green: Optimal signal
4. When the top right light ashes red, 30 seconds remain
before the photo mode is turned ON. This allows you to leave
the area without being photographed.
10
ENGLISH
5. The camera is ready for use when all the lights turn OFF.
6. If the light is red during step 3, you should:
• Turn your camera OFF and then back ON.
• Retry while pointing the antenna at different angles.
• Try moving it to a spot with better signal.
• Try our #CA-01 long range cellular antenna (sold separately),
which could help improve signal strength.
INSTALLING YOUR CAMERA
1. Mount the camera using the installation strap.
2. The camera should be at the same height as the animal’s
mid-body.
3. The targeted animal should be at 25 feet (7.5 meters) away
from the camera.
4. To produce brighter photos at night, there sould be items
reflecting the camera's flash in the background.
Otros manuales para LINK-MICRO-LTE
4
Tabla de contenidos
Idiomas:
Otros manuales de Cámara de exploración de Spypoint
Spypoint
Spypoint LINK-MICRO-S-LTE Manual de usuario
Spypoint
Spypoint FLEX Manual de usuario
Spypoint
Spypoint Force-Dark Manual de usuario
Spypoint
Spypoint Solar-Dark Manual de usuario
Spypoint
Spypoint LINK-MICRO-LTE Manual de usuario
Spypoint
Spypoint LINK-MICRO 680097 Guía
Spypoint
Spypoint Force-Dark Manual de usuario
Spypoint
Spypoint CELL-LINK Manual de usuario
Spypoint
Spypoint LIVE-3G Manual de usuario
Spypoint
Spypoint FORCE-10 Manual de usuario
Spypoint
Spypoint LING-4G Manual de usuario
Spypoint
Spypoint LINK-S-DARK Manual de usuario
Spypoint
Spypoint FORCE-20 Manual de usuario
Spypoint
Spypoint LIVE Manual de usuario
Spypoint
Spypoint LINK-MICRO Manual de usuario
Spypoint
Spypoint Solar-Dark Manual de usuario
Spypoint
Spypoint LM2 Manual de usuario
Spypoint
Spypoint LINK-S-DARK Manual de usuario
Spypoint
Spypoint FORCE-PRO-S Manual de usuario
Spypoint
Spypoint SOLAR Manual de usuario
