Sper scientific 850006 Guía de instalación y uso
LED Light Meter with
Color Temperature Correction
850006
Instruction Maual
2 3
INTRODUCTION ................................ 3
FEATURES ..................................... 4
MATERIALS SUPPLIED ........................... 5
CARE AND MAINTENANCE ....................... 5
FRONT PANEL DESCRIPTION ..................... 6
LCD DISPLAY................................... 7
SETUP ........................................ 8
ZERO CALIBRATION ............................. 9
ACCESSING THE INTERNAL MEMORY ............. 9
MEASUREMENT PROCEDURES .................. 10
LUMINOUS INTENSITY.......................... 12
SPECTRAL SENSITIVITY ........................ 13
SPECIFICATIONS .............................. 14
WARRANTY................................... 15
TABLE OF CONTENTS
3
INTRODUCTION
This Sper Scientic LED light meter with color temperature
correction (model 850006) is specically designed to measure
modern LED bulbs over the wide range of color-temperature
varieties commercially available in today’s lighting industry.
This unique meter includes all the features of a standard
LED light meter and also has individual channels specically
designed to measure dierent color-temperatures of LED light
bulbs. A simple intuitive keypad allows you to begin using the
device immediately in Foot Candles (FC), Lux (Lx), or Luminous
Intensity (CD). The user can preset the source distance for an
even more thorough analysis, showing readings on the large
LCD display. With a Min/Max/Average, Auto-Ranging Intensity,
99-point internal memory, Hold function, and a single-button
zero calibration, this meter covers every available feature of
competitive light meters. Comes with a universal tripod screw
in a compact carrying case with 9V battery, lens cover, and
instructions.
4 5
FEATURES
• Min/Max/Average
• 7 pre-programmed LED channels
• Hold Function
• 1 Adjustable channel
• 99-point internal memory
• 1 standard non-LED channel
• Luminous Intensity (CD)
• Reads Foot Candle (FC) and Lux (Lx)
• Distance-to-source feature
• Tripod mountable
5
MATERIALS SUPPLIED
• LED Light meter
• Carrying Case
• Lens cover
• 9V Battery
• Instruction manual
CARE AND MAINTENANCE
• Store the meter in its protective case with the lens
cover closed to protect the sensor.
• Do not use abrasives, solvents or cleaning agents
containing carbon, alcohol or benzenes on the meter.
• Repairs or services not covered in this manual should
be performed by qualied personnel only. Please
contact Sper Scientic to speak with a technician.
6 7
FRONT PANEL DESCRIPTION
1. LCD Screen
2. Light Units
3. Memory/Recall
4. UP Arrow
5. Power Button
6. Auto Zero Button
7. HOLD / Channel Selector
8. DOWN Arrow
9. Photosensor
10. Lens Cap
7
LCD DISPL AY
1. Automatic Power-o Enabled
2. Internal Memory Enabled
3. Hold Function Enabled
4. Luminous Intensity Activated
5. Foot Candle Reading
6. Lux Reading
7. Low Battery Indicator
8. Light Correction Factor (Channels 8 and 9 only)
9. Current Channel Indicator
10. Internal Memory Identier
11. Memory Recall Mode Activated
8 9
SET UP
Battery Installation
1. This meter comes with a 9V battery.
2. Slide the rear cover down to expose the battery.
3. Gently pull out the 9V battery from the housing and
install the 9V battery, ensuring correct polarity.
4. Place the installed battery back into the housing, being
sure not to pinch the wires of the plug.
5. Replace the rear cover.
6. Repeat these steps when the low battery indicator
shows on the LCD screen.
Power On and O
1. Press the POWER button for less than one second to
turn the meter on in auto shut-o mode.
This will be evident by the power icon in the upper
left corner of the screen. In this mode, the meter will
power o after 5 minutes of inactivity.
2. To disable the auto power-o feature, turn the meter
on by pressing the POWER button for more than 2
seconds and release. The meter will turn on and the
power icon will NOT be present.
3. To turn the meter o at any time, press the POWER
button once.
9
ZERO CALIBRATION
1. Turn the meter on.
2. Place the lens cap on the sensor.
3. Press ZERO.
4. The screen will momentarily display “Adj” to indicate
your zero calibration was successful.
5. If the screen does not display “Adj”, the calibration was
not successful.
6. If the screen displays “CAP,” please ensure the lens
cap is tightly secured over the photosensor and try
again.
ACCESSING THE INTERNAL MEMORY
1. Turn the meter on.
2. Hold MEM until the lower left corner of the screen
displays “R”.
3. Use the UP and DOWN arrows to scroll through the
saved values. Note that the unit of measure stays with
the measurement.
4. Press MEM once to exit memory recall mode.
5. To clear the internal memory at any time, rst turn the
meter o. Then, while holding the MEM key, turn the
power on. “Clr” will display on the screen, indicating that
you have cleared the memory.
10 11
MEASUREMENT PROCEDURES
1. Turn the meter on.
2. Select your desired units by pressing LX/FC/CD to toggle
between Lux and Footcandles.**
**Note: If you want to activate the CD function, press
LX/FC/CD for more than 2 seconds to activate this mode,
explained on page 12.
3. Select your desired channel by pressing HOLD for more
than 2 seconds. The LS numerical value will blink at the
bottom of the screen.
4. Use the UP and DOWN arrows to change the L-value
to the desired channel. Use the Chart on the right as a
guide.
5. To conrm your channel selection, press HOLD for
more than 2 seconds again. The channel value will stop
blinking and the meter returns to regular measuring
mode.
6. Aim the photosensor at the light source. For best results,
hold the sensor as close to perpendicular as possible.
7. To freeze the reading on-screen, press HOLD. The value
will remain on the screen until you press HOLD again.
8. To view the MIN/MAX/AVERAGE over any interval, press
the UP arrow to scroll through the minimum, maximum,
and average values since the last time this feature was
activated. Press the UP arrow for more than 2 seconds to
exit this feature.
9. To store a reading in the meter’s internal memory, press
MEM. A numerical value will temporarily show in the
lower left side of the LCD screen, indicating successful
storage. You can also store an average value by pressing
MEM during a min/max/average measurement.
Tabla de contenidos
Otros manuales de Instrumento de medición de Sper scientific
Sper scientific
Sper scientific 300003 Manual de usuario
Sper scientific
Sper scientific 800048 Manual de usuario
Sper scientific
Sper scientific 800021 Manual de usuario
Sper scientific
Sper scientific 850009 Manual de usuario
Sper scientific
Sper scientific 300005 Manual de usuario
Sper scientific
Sper scientific 840003 Manual de usuario
Sper scientific
Sper scientific 800100 Manual de usuario
Sper scientific
Sper scientific 840021 Manual de usuario
Sper scientific
Sper scientific 860041 Manual de usuario
Sper scientific
Sper scientific 300001 Manual de usuario
Sper scientific
Sper scientific 840062 Manual de usuario
Sper scientific
Sper scientific Large Display Salinity Pen - 850036 Manual de usuario
Sper scientific
Sper scientific 300058 Manual de usuario
Sper scientific
Sper scientific 300058 Manual de usuario
Sper scientific
Sper scientific 800012 Manual de usuario
Sper scientific
Sper scientific 850039 Manual de usuario
Sper scientific
Sper scientific 840005 Manual de usuario
Sper scientific
Sper scientific 800020 Manual de usuario
Sper scientific
Sper scientific 840018 Manual de usuario
Sper scientific
Sper scientific 850003 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario