Speco O6MDP3N Manual de usuario
Quick Start Guide
O6MDP3N
Welcome
Thank you for purchasing this network camera!
This owner's manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, contact Speco Technologies Tech Support at
1-800-645-5516
1. Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time;
it may result in device damage! The product must be grounded to reduce the risk of
electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation,
storage and installation.
This product should be installed in a cool, dry place away from direct sunlight and heat
sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS
sensor failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any
maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on
the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth
Important Safeguards and Warning
Warning
Statement
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
.
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco
Technologies reserves the right to modify these without notice and without incurring
any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is
broken or missing in the package.
dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean
the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure
cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance
the reliability of the camera.
Package
1
Camera Quick start guide Drill template Screwdriver
Overview
2
1
3
4
5
6
7
8
9
2
1 Ethernet Connector
2 MIC IN
3 HP Audio Output
4 Video Output
5 Alarm Input/Output
6 RS485
7 DC12V Power Supply
8 SD Card Slot
9 Reset
CD Plastic plug × 3
Tapping screws ×3 Junction box
ALM-COM
ALM-OPEN
ALM-INA
ALM-GND
RS485T+
RS485T-
DC12V
* 1 It is recommended to install the security cap for outdoor installations.
* 2 DC 12V power supply is not required if a PoE switch or injector is used to power
the camera.
2
13
● Connecting Network Cable
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the water-proof connector. Then tighten the
nut and the main cover.
Please install and use the camera in the dry environment. You'd better
install back the cover less than 4 hours after removing it.
Installation
3
① Remove the fixed ring from the gap of the camera.
Gap
Fixed Ring
② Install the junction box onto the wall.
③ Route the cables through the cable hole (take side conduit cabling
for example) and connect the cables. Then fix the camera onto the
junction box with screws.
Rubber plug
④Install the fixed ring back to finish the installation.
Web Operation and Login
4
● Operation
IP Scanner can search for the device on the local network.
① Make sure that the camera and the PC are connected to the
same local network. The camera is set to DHCP by default.
5C :F2:0 7: 24:68 :B9
O6 MD P3 N
The login interface is shown above. Default user name is admin and
password is 1234. After logging in, follow directions to install
applicable plugins.
③ In the device list, you can view the IP address, model number, and
MAC address of each device. Select the applicable device and double
click to open up the web viewer. You can also manually enter the IP
address in the address bar of the web browser.
② Install IP Scanner from the CD and run it after installation.
Otros manuales para O6MDP3N
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de Speco
Speco
Speco O2P20X Manual de usuario
Speco
Speco VLEDT2HG Manual de usuario
Speco
Speco O5B2 Manual de usuario
Speco
Speco O4VB2 Manual de usuario
Speco
Speco O8D2M Manual de usuario
Speco
Speco HT-647HRTP Manual de usuario
Speco
Speco CVC-652HZ Manual de usuario
Speco
Speco O8VB1 Manual de usuario
Speco
Speco HTD8FFI Manual de usuario
Speco
Speco HHDI04D1B Manual de usuario
Speco
Speco CVCM6DC Manual de usuario
Speco
Speco CVC6146SCS Series Manual de usuario
Speco
Speco O8FD1 Manual de usuario
Speco
Speco PROVIDEO CVC-627 Manual de usuario
Speco
Speco VIP2B3 Manual de usuario
Speco
Speco WDRB1 Manual de usuario
Speco
Speco HT770PH Manual de usuario
Speco
Speco HT-7815DNV Manual de usuario
Speco
Speco CVC-607EXCM25 Manual de usuario
Speco
Speco O4FB1 Manual de usuario
