Speco O5B2M Manual de usuario
Quick Start Guide
O5B2M
Welcome
Thank you for purchasing this network camera!
This owner's manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, contact Speco Technologies Tech Support at
1-800-645-5516
1. Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time;
it may result in device damage! The product must be grounded to reduce the risk of
electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation,
storage and installation.
This product should be installed in a cool, dry place away from direct sunlight and heat
sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS
sensor failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any
maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on
the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth
Important Safeguards and Warning
Warning
Statement
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
.
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco
Technologies reserves the right to modify these without notice and without incurring
any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is
broken or missing in the package.
dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean
the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure
cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance
the reliability of the camera.
Package
1
Camera Quick start guide CD
Overview
3
Plastic plug × 4 Junction box
4 tapping screws
Overview
2
Drill Template
1 machine screw
CVBS&DC
IN cables Screwdriver
1 Ethernet Connector *
2 Audio Input (MIC)
3 Audio Output (HP)
4 CVBS Video Output
5 Alarm Input/Output
6 Power Connector *
7 Reset*
8 DC IN&CVBS Interface
9 Zoom -
10 Zoom +
11 Micro SD Card Slot
1
3
4
5
6
2
ALARM
4 3 2 1
7
8
9
10
11
* 1 It is recommended to install the security cap for outdoor installations.
* 2 DC 12V power supply is not required if a PoE switch or injector is used to power
the camera.
► Connecting Network Cable
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through both
elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the nut
and the main cover.
2
13
Security cap
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
DC12V
ALARM
4 3 2 1
Installation
3
* Before you start, please make sure that the wall or ceiling is strong enough
to withstand three times the weight of the camera.
① Open the mounting base and the upper cover of the junction box.
② Install junction box onto the wall by using the screws provided.
③ Fix the mounting base of the camera to the upper cover of the junction
box.
Mounting base
Upper cover
④ Route the cables through the cable hole and connect the camera. Then install
the camera onto the mounting base of the junction box.
Three-axis Adjustment-Before adjustment, preview the image of the camera
on a monitor and then loosen the fixed screws to adjust the camera according to
the figure below to get an optimum angle.
⑤
③In the device list, you can view the IP address, model number, and
MAC address of each device. Select the applicable device and double
click to open up the web viewer. You can also manually enter the IP
address in the address bar of the web browser.
Web Operation and Login
4
●Operation
IP Scanner can search for the device on the local network.
①Make sure that the camera and the PC are connected to the same
local network. The camera is set to DHCP by default.
②Install IP Scanner from the CD and run it after installation. Or
download from https://www.specotech.com/ip-scanner/
Tilt 90°
Pan 360°
Rotate
360°
Fixed screws
5C :F2:0 7: 24:68 :B9
O5 B2M
The login interface is shown above. Default user name is admin and
password is 1234. After logging in, follow directions to install
applicable plugins if prompted.
Tabla de contenidos
Otros manuales de Cámara de seguridad de Speco
Speco
Speco CVC5300DPVF Manual de usuario
Speco
Speco O4VB1MN Manual de usuario
Speco
Speco O2T7 Manual de usuario
Speco
Speco VL-262SD Manual de usuario
Speco
Speco HT-650IRVFHQ/S Manual de usuario
Speco
Speco CVC-627B Manual de usuario
Speco
Speco PROVIDEO CVC-627 Manual de usuario
Speco
Speco VLB9 Manual de usuario
Speco
Speco OINT56B Manual de usuario
Speco
Speco CVC-812PC Instrucciones de instalación
Speco
Speco Intensifier HTINT59K1 Manual de usuario
Speco
Speco CVC-3805 Manual de usuario
Speco
Speco CILT13D1G Manual de usuario
Speco
Speco O2D60M Manual de usuario
Speco
Speco HTSD10X Manual de usuario
Speco
Speco O4B7 Manual de usuario
Speco
Speco WC-2503 Manual de usuario
Speco
Speco CVCM6DC Manual de usuario
Speco
Speco o2vld5 Manual de usuario
Speco
Speco VLD2A Manual de usuario
