Sony Ipela PCS-G50 Guía

Integration with

Sony Network Camera

VIDEO COMMUNICATION SYSTEM-TECHNICAL DOCUMENTATION

PCS-G50/G50P Ver. 2.61 or later

PCS-G70/G70P Ver. 2.61 or later

ソニー製ネットワークE.qxd08.2.183:53PMページ1

VIDEO COMMUNICATION SYSTEM-TECHNICAL DOCUMENTATION

Integration with Sony Network Camera

Introduction

The Sony Visual Communication System PCS-G50/G70 is the first in the industry

with features that allow connection with network cameras. These features allow

you to connect to Sony network cameras as if you were calling a videoconference

partner. In addition to viewing network camera images through the PCS-G50/G70,

audio exchange is also possible between the PCS-G50/G70 and the network

cameras, and pan, tilt and zoom operations can be performed on network cameras

through the PCS-G50/G70. Furthermore, the cameras can be used to conduct

multipoint conferences with a mixture of connections, such as IP and ISDN.

These integration features expand the potential of new applications beyond

conventional videoconferencing.

This document describes the network camera integration features supported by the

PCS-G50/G70.

* In this document, PCS-G50/G70 refers to both the NTSC PCS-G50/G70 and PAL PCS-G50P/G70P models.

Main Terminal

PCS-G50/G70

SNC-RZ50N/RZ50P

SNC-CS50N/CS50P

SNC-RX550N/RX550P

ISDN (H.320)

Sub-terminal

IP (H.323/SIP)

IP, UDP (Unicast) transmission

IP, UDP (Multicast) transmission

IP, TCP transmission

Connection Example

ソニー製ネットワークE.qxd08.2.183:53PMページ2

VIDEO COMMUNICATION SYSTEM-TECHNICAL DOCUMENTATION

Integration with Sony Network Camera

Main Features

Video/Audio Types

H.264 and MPEG4 are supported for video (for single codec only).

G.711 is supported for audio.

You can monitor real-time network camera images and transmit voice data bi-

directionally through the PCS-G50/G70 during a videoconference.

Easy Connection

Through the phone book (called the “network camera list”) of the PCS-G50/G70,

you can easily connect to a network camera using a procedure similar to that for

videoconferencing. You can register up to 20 network cameras in the network

camera list.

•The network camera list is separate from the 500 items in the ordinary phone

book.

•Private and shared phone books are not supported.

•To register a network camera in the network camera list, see the PCS-G50/G70

Operating Instructions Manual (Version 2.6).

Multipoint Connection

Up to 6 points (including the local site) can be connected, and split-screen viewing is

possible. Multipoint connection in a mixed IP (H.323/SIP) and ISDN environment is

possible for video communication terminals.

•For multipoint connection, MCU software for LAN connection (sold separately)

is required.

•For multipoint connection in a mixed SIP and ISDN environment, SIP software

and MCU software for ISDN connection (sold separately) are required.

Far End Camera Control

You can use the far end camera control function when connected to a network

camera. The procedures for acquiring broadcast permission for the target network

camera and for controlling the far end camera are the same as for when the

PCS-G50/G70 is used at a remote site.

•To use the far end camera control function, you must have the proper permission

settings. (See p.5.)

•If the far end camera control function is enabled by the PCS-G50/G70, it can

also be used from video communication terminals as sub-terminals.

•The far end camera control function can be used in full screen display mode

only.

ソニー製ネットワークE.qxd08.2.183:53PMページ3

VIDEO COMMUNICATION SYSTEM-TECHNICAL DOCUMENTATION

Integration with Sony Network Camera

Preset Function

You can use the preset function (from 1 to 6 preset positions) for the network

camera connection. You can also register preset positions through the

PCS-G50/G70. The procedures for registering and calling up the presets are the

same as for when the PCS-G50/G70 is used at a remote site.

•To use the preset function, you must have the proper permission settings.

(See p.5.)

Status Indication

As with the videoconferencing connection, you can use the Status menu for the

network camera connection to check the communication status during

communication, as well as the previous communication status while not in

communication.

•When using a TCP connection, lost and recovered packet counts are not

displayed.

Web Function

Using Microsof®Internet Explorer®(version 5.0 or higher, 6.0 is recommended),

you can access the PCS-G50/G70 to perform control and change settings for a

network camera.

Terminal Name Indication

You can use the terminal name indication function for the network camera

connection.

When this feature is enabled, the name of the title bar configured on the System

Menu of the connecting network camera is displayed on the videoconferencing

screen.

Other Precautions

You cannot perform the following PCS-G50/G70 functions when connected to a

network camera (even between videoconferencing terminals):

•Sending/receiving a presentation image

•Sending dual video

•Sending a still image

•Encrypted conference

•Cascade connection

ソニー製ネットワークE.qxd08.2.183:53PMページ4

VIDEO COMMUNICATION SYSTEM-TECHNICAL DOCUMENTATION

Integration with Sony Network Camera

For the reasons outlined below, do not connect to network cameras used for

monitoring. It is recommended that network cameras be installed exclusively for

videoconferencing.

•The PCS-G50/G70 does not support JPEG. JPEG recording may stop when the

PCS-G50/G70 is connected to a monitoring system where Sony Recorder

Software (RealShot Manager, IMZ series), Sony Network Recorder (NSR series),

etc. is used.

•Connecting a video communication terminal to a network camera used for fixed

monitoring and far-end controlling may result in a loss of monitoring

information.

When the SNC-RX550N/RX550P is installed on a desktop, the video image will be

displayed upside down. The PCS-G50/G70 has no vertical flip function.

(This image illustrates the connection between video communication terminals and network cameras.

The screen image is simulated.)

User Authority

Multiple users can be registered for a Sony network camera, and a name,

password and authority can be specified for each user. Connection from the

PCS-G50/G70 to a network camera is made using a predefined user name and

password. The operation and settings for a network camera can be limited based

on the user authority.

Network Camera User Authority

Table 1 shows the functions available for the administrator and user authorities.

Only those functions related to PCS integration are listed.

Note

ソニー製ネットワークE.qxd08.2.183:53PMページ5

VIDEO COMMUNICATION SYSTEM-TECHNICAL DOCUMENTATION

Integration with Sony Network Camera

Full Pan/ Preset Light View

Tilt Position

Monitor live image ●●●●

Call up preset position*1

●●●×

Perform pan/tilt/zoom ●●××

operations

Receive audio ●●●●

Control the setting menu*2●×××

Table 1

User

Administrator

Authority

Function

●: Function available ×: Function not available

*1: Up to 6 preset positions can be used.

Through the PCS-G50/G70, you can call any of the six registered preset positions (No.1 to No.6) in the preset position

table in the network camera's Preset Position Menu.

*2: This function overwrites the network camera's settings. See the “Determined Communication Mode Based on

Authority” section for details.

When you connect using the administrator authority, you can change the settings

of a network camera from the PCS-G50/G70. You can change the settings through

the Network Camera page in the PCS's General Setup menu. If "Auto" is selected

for "Bit Rate," "Frame Rate," "Mode" and "Image Size," the connection is made

using the settings of the connecting network camera.

If the connection is made using the administrator authority with the setting items

set to "Auto," the connection can be made by properly changing the network

camera settings even if a preconfigured item in the network camera setup is not

supported by the PCS-G50/G70. For details on the communication modes

supported by the PCS-G50/G70, refer to "Basic Specifications" at the end of this

document.

In addition, the far end camera control and preset functions can be used under the

administrator authority.

When the network camera settings are changed via the PCS-G50/G70, the

previously set network camera settings are automatically restored after

communication has ended.

Operating with Administrator Authority in PCS Integration

•Connections made using the administrator authority automatically change the

network camera settings and may affect a monitoring system using the network

camera, so you must consult with your system administrator beforehand.

•If a connection shuts down due to a failure such as a blackout, the settings

cannot be restored. It is therefore recommended to save the camera's setting

data in a file prior to connection. For details on how to save/restore the setting

data, see the User's Guide that came with the network camera.

Note

ソニー製ネットワークE.qxd08.2.183:53PMページ6

VIDEO COMMUNICATION SYSTEM-TECHNICAL DOCUMENTATION

Integration with Sony Network Camera

When a connection to a network camera is made using the administrator

authority, the modes described below will automatically be changed.

• Audio Codec

If the audio codec setting (used to send audio) of the network camera is G.726, it

will automatically be changed to G.711.

• Audio (Bidirectional)

If the audio upload setting of the network camera is disabled, it will automatically

be enabled to perform voice communication from the video communication

terminal to the network camera. If the microphone setting of the network camera is

OFF, it will automatically be turned ON to perform voice communication from the

network camera to the video communication terminal as well.

• Multicast Streaming

If the multicast streaming setting of the network camera is OFF and the connection

is made through UDP (Multicast), multicasting will automatically be turned ON for

the connection using UDP (Multicast).

• Unicast Streaming

If the network camera's unicast streaming setting (video or audio port number)

overlaps with the port number used by the PCS-G50/G70, it will automatically be

changed to another number for connection.

You cannot change the network camera setting items through the PCS-G50/G70.

You must use the network camera to configure settings related to the connection

with the PCS-G50/G70. (Settings configured through the Network Camera page in

the PCS's General Setup menu will be disabled.)

To use the camera control and preset functions via the PCS-G50/G70, you must

properly configure the network camera's User menu. (See Table 1.)

Operating with User Authority in PCS Integration

ソニー製ネットワークE.qxd08.2.183:53PMページ7

VIDEO COMMUNICATION SYSTEM-TECHNICAL DOCUMENTATION

Integration with Sony Network Camera

Authority Used for Connection

Camera Menu Setting

(on Network Camera)

Administrator User

Connection is made using the PCS setting value

regardless of the network camera setting.*1

When the PCS setting is "Auto," however, the

network camera settings are prioritized.

Connection is made using the PCS setting value

regardless of the network camera setting.

When the PCS setting is "Auto," however,

connection is made by automatically changing

the network camera setting to a mode

supported by the PCS (H.264 single codec).*1

Connection is made using G.711.

Connection is made using the network

camera setting (H.264 single codec).

Connection is made using the network

camera setting (MPEG4 single codec).

Connection is not possible if no action is

taken.

To make the connection, use the

network camera to switch the mode to

one that is supported by the PCS.

Connection is made using the network

camera setting (G.711).

H.264

MPEG4

Connection is made using the network

camera setting (QQVGA).

Connection is made using the network

camera setting (QVGA).

JPEG

Dual Codec

G.711

Connection is made by automatically changing

the network camera setting to the audio codec

supported by the PCS (G.711) regardless of the

network camera setting. *1

Audio is not available between the

video communication terminal and

network camera.*2

G.726

Connection is made using the PCS setting value

regardless of the network camera setting.

When the PCS setting is "Auto," however,

connection is made by automatically changing

the network camera setting to an image size

supported by the PCS (QVGA). *1

Connection is not possible if no action is

taken.

To make the connection, use the

network camera to switch the image

size to one that is supported by the PCS.

VGA

Connection is made using the PCS setting value

regardless of the network camera setting.*1

When the PCS setting is "Auto," however, the

network camera setting is prioritized.

QQVGA

QVGA

Connection is made using the network

camera setting.

Connection is made using the PCS setting value

regardless of the network camera setting.*1

When the PCS setting value is "Auto," however,

the network camera setting is prioritized.*3

Bit Rate

Connection is made using the PCS

setting. In addition, the network camera

setting is required.*4

Connection is made using the PCS setting value

regardless of the network camera setting. *1

Transmission Mode

(TCP/UDP)

Frame Rate

Mode Audio Codec Image Size

Single Codec

(“PCS” in the table below refers to the main terminal of the PCS-G50/G70.)

Determined Communication Mode Based on Authority

*1: When the network camera settings are changed for the connection, the previously set network camera settings are

automatically restored after communication has ended.

*2: Videoconferencing connection is possible, even if G.726 is selected. Upon connection, a message is displayed

prompting the user to switch the audio codec.

To use audio for videoconferencing, switch to G.711 on the network camera.

*3: Even if 30fps is selected, the rate is automatically set to 15fps (NTSC) or 12fps (PAL) if the mode is H.264 and the

transmission mode is TCP.

*4: If the network camera setting is improper, a message is displayed prompting the user to make the proper setting.

ソニー製ネットワークE.qxd08.2.183:53PMページ8

VIDEO COMMUNICATION SYSTEM-TECHNICAL DOCUMENTATION

Integration with Sony Network Camera

User authority must be configured on both the network camera and the

PCS-G50/G70. This section provides an overview of the settings. For details, see

the User's Guide that came with the network camera and the PCS-G50/G70

Operating Instructions Manual (Version 2.6).

On Network Camera

How to Configure User Authority

On PCS-G50/G70

On the network camera list edit screen, enter a name and IP address for the

camera you want to register, as well as the user name and password specified on

the network camera.

(To connect using the administrator authority, the user name and password must

be registered as "Administrator" in the network camera's User menu.)

ソニー製ネットワークE.qxd08.2.183:53PMページ9

VIDEO COMMUNICATION SYSTEM-TECHNICAL DOCUMENTATION

Integration with Sony Network Camera

Communication Mode for Multipoint Connection

The operation specifications and the determined communication mode may vary

according to the user authority used for connection.

Some examples are provided below. (“PCS” in the table below refers to the main

terminal of the PCS-G50/G70.)

Operational Specifications 1: When only network cameras are connected as

sub-terminals

Operational Specifications Connection

Condition

1-a

Determined Communication Mode

Authority

When sub-terminals are

connected within the

range of the LAN

bandwidth of the main

PCS

When each setting on the main PCS's

network camera page is set to a setting other

than "Auto":

Connection is made using the setting values of

the main PCS. The operation mode and image

size are always determined by the PCS setting

values. (They cannot be changed

automatically.)

When each setting on the main PCS's

network camera page is set to "Auto":

In principle, operations follow each network

camera's setting values.*1

Administrator

Authority

User

Authority

See

example

1-a-1(1)

1-b When sub-terminals

exceed the range of the

LAN bandwidth of the

main PCS

When the bit rate exceeds the PCS's LAN

bandwidth, it is automatically changed to the

optimum rate regardless of the main PCS's

network camera settings.

Administrator

Authority

See

example

1-b-1

When the bit rate exceeds the PCS's LAN

bandwidth, it is automatically changed to the

optimum rate for cameras connected with the

administrator authority, while the mode is

changed to "Voice Only" for cameras connected

with the user authority if capability exchange is

required again, regardless of the main PCS's

network camera settings.

Mixed

Administrator

and User

Authority

See

example

1-b-3

When the bit rate exceeds the PCS's LAN

bandwidth, the mode is changed to "Voice Only"

from the added camera regardless of the main

PCS's network camera settings.

User

Authority

See

example

1-b-2

See

example

1-a-1(2)

Regardless of the main PCS's network camera

settings, operations follow each network

camera's setting values.

See

example

1-a-2

Mixed

Administrator

and User

Authority

Cameras connected with the administrator

authority and cameras connected with the

user authority operate independently of each

other, with the specifications described above.

*1: The PCS automatically switches communication modes not supported by the PCS (JPEG, dual codec, VGA, G.726,

30fps on H.264 and TCP) to a supported one.

ソニー製ネットワークE.qxd08.2.183:53PMページ10

Otros manuales para Ipela PCS-G50

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de conferencias de Sony

Sony

Sony PCS-11 Manual de usuario

Sony

Sony IPELA PCS-G70 Manual de usuario

Sony

Sony ixs-6600 Manual de usuario

Sony

Sony PCSXG100S Manual de usuario

Sony

Sony IPELA PCS-G70 Manual de usuario

Sony

Sony Ipela PCS-XG80 Manual de usuario

Sony

Sony PCS-1 - Video Conferencing Kit Manual de usuario

Sony

Sony PCS-VCS IPELA Manual de usuario

Sony

Sony PCS-G70N Manual de usuario

Sony

Sony Ipela PCS-TL50 Manual de usuario

Sony

Sony Ipels PCS-G50 Manual de instrucciones

Sony

Sony PCS-1 - Video Conferencing Kit Manual de usuario

Sony

Sony Ipela PCS-XC1 Manual de usuario

Sony

Sony SXA-120 Manual de usuario

Sony

Sony BRU-300 Manual de usuario

Sony

Sony PCS-1600 Manual de usuario

Sony

Sony IPELA PCS-TL33 Manual de usuario

Sony

Sony Ipela PCS-XG80 Manual de usuario

Sony

Sony PCS-P160 Manual de usuario

Sony

Sony SX-1070A Manual de usuario

Sony

Sony Ipela PCS-G70S Manual de usuario

Sony

Sony Ipela PCS-XC1 Manual de instrucciones

Sony

Sony Ipels PCS-G50 Manual de usuario

Sony

Sony PCS-1 - Video Conferencing Kit Manual de usuario

Manuales populares de Sistema de conferencias de otras marcas

Kramer

Kramer VIA GO Manual de usuario

AVT

AVT MAGIC AC1 Go Manual de usuario

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manual de usuario

Middle Atlantic Products

Middle Atlantic Products VTC Series Manual de usuario

Prentke Romich Company

Prentke Romich Company Vanguard Plus Guía

Speakerbus

Speakerbus iD 712 Manual de usuario

Trelleborg

Trelleborg SafePilot CAT PRO Manual de usuario

Sennheiser

Sennheiser ADN Manual de usuario

ADTRAN

ADTRAN NetVanta 7100 Manual de usuario

AINA

AINA PTT Voice Responder Manual de usuario

Yamaha

Yamaha ProjectPhone PJP-100H Manual de usuario

vissonic

vissonic VLI Series Manual de usuario

Panasonic

Panasonic KX-VC500 Manual de usuario

Poly

Poly Trio 8300 Manual de usuario

Crestron

Crestron Mercury CCS-UCA-SMK Dibujo dimensional

Inmarsat

Inmarsat mini M Manual de usuario

Tenveo

Tenveo ALL-IN-ONE Manual de usuario

AXIWI

AXIWI AT-350 Manual de usuario