Solaris PIX 72 Manual de usuario

USER MANUAL

PIX |72

basic pixel bar 24x3w

SOLARIS® PIX 72™ 2

INDEX PAGE NO.

SAFETY INFORMATION 3-4

INTRODUCTION 5

INSTALLATION 6

AC POWER 7

FIXTURE OVERVIEW 8

DMX DATA LINK 9

CONNECTING AND USING DMX DATA LINK 9

FIXTURE OPERATION 10

TOKENS 11

FIXTURE MENU STRUCTURE CHART 12

DMX MODES CHARTS 13-14

MAINTENANCE 15

PIX 72 SPECIFICATIONS 16-17

INCLUDED ITEMS 17

TABLE OF CONTENTS

3SOLARIS® PIX 72™

WARNING!

READ THE SAFETY PRECAUTIONS IN THIS MANUAL

BEFORE INSTALLING

OPERATING OR SERVICING THIS PRODUCT.

SAFETY NOTES

Read all the following Safety Notes before working with this product.

These notes include important informaon about the installaon, us-

age, and maintenance of this product.

This product contains no user-serviceable parts. Any reference to ser-

vicing in this User Manual will only apply to properly trained GLOW®

Professional cered technicians. Do not open the housing or aempt

any repairs.

All applicable local codes and regulaons apply to proper installaon of

this product.

PERSONAL SAFETY

· Avoid direct eye exposure to the light source while the product is on.

· Always disconnect this product from its power source before servicing.

· Always connect this product to a grounded circuit to avoid the risk of

electrocuon.

· Do not touch this product’s housing during operaon because it may

be very hot.

MOUNTING & RIG-

GING

· This product is for indoor use only! To prevent risk of re or shock, do

not expose this product to rain or moisture. (IP20)

· Mount this product in a locaon with adequate venlaon, at least 20

in (50 cm) from adjacent surfaces.

· Make sure there are no ammable materials close to this product while

it is operang.

· Always carry this product by the handles. Do not carry from the head.

· When hanging this product, always secure to a fastening device using

a safety cable.

SAFETY INFORMATION

SOLARIS® PIX 72™ 4

POWER & WIRING

· Always make sure you are connecng this product to the proper volt-

age in accordance with the specicaons in this manual or on the prod-

uct’s specicaon label.

· Never connect this product to a dimmer pack or any rheostat.

· Never disconnect this product

OPERATION

· Do not operate this product if you see damage to the housing, lenses,

LED lights or cables. Have the damaged parts replaced by an authorized

technician at once.

· Do not cover the venlaon slots when operang to avoid internal

overheang.

· Do not aim this product toward the Sun. The lenses could concentrate

the solar energy and cause internal overheang.

· The maximum ambient temperature is 120 °F (49 °C). Do not operate

this product at a higher temperature.

· In case of a serious operang problem, stop using this product imme-

diately

In the unlikely event that your GLOW® product may require service, contact GLOW®

Technical Support.

5SOLARIS® PIX 72™

The SOLARIS® PIX 72™ is a high-performance 24 X 15W RGB 3 in 1 Pixel Led Bar lighng

xture featuring a Linear Dimmer & a light weighted body enclosure made of a sturdy alumi-

num casng, designed for xed indoor installaons.

The xture can be controlled using any DMX-compliant controller (2 Ch. | 3 Ch. | 4 Ch. |

6 Ch. | 7Ch. | 12 Ch. | 24 Ch. Modes) as well as automac operaon mode, sound to light

mode and manual mode.

BEFORE USING THE PRODUCT FOR THE FIRST TIME

1. Read ’Safety informaon’ on page 4 before installing, operang or servicing the xture.

2. Unpack and ensure that there is no transportaon damage before using the xture. Never

aempt to operate a damaged xture.

3. If the xture is not going to be hard-wired to a mains supply, aach a local power plug to

the end of the supplied power cable.

4. Before operang, ensure that the voltage and frequency of the power supply match the

power requirements of the xture.

5. Refer to the GLOW® website for the most recent user documentaon and technical infor-

maon about this xture.

INTRODUCTION

SOLARIS® PIX 72™ 6

INSTALLATION

The xture is designed for indoor use only and must be used in a dry locaon with adequate

venlaon. Ensure that none of the xture’s venlaon slots are blocked and ensure that the

xture is fastened to a secure structure or surface. Do not use the xture to illuminate sur-

faces less than 8 m (approx 26.) from the xture.

FASTENING THE FIXTURE TO A FLAT SURFACE

The xture can be fastened to a hard, xed, at surface that is oriented at any angle. Ensure

that the surface and all fasteners used can support at least 10 mes the weight of all xtures

and equipment they will support. Fasten the xture Securely. Do not place it on a surface or

leave it where it can be moved or fall over. If you install the xture in a locaon where it may

cause injury or damage if it falls, secure it as directed below with a securely anchored safety

cable that will hold the xture if the primary fastening method fails.

MOUNTING THE FIXTURE ON A TRUSS

The xture can be clamped to a truss or similar rigging structure in any orientaon. When

installing the xture hanging vercally down, you can use an open-type clamp such as a

G-clamp. When installing in any other orientaon, you must use a half-coupler clamp

that completely encircles the truss or pipe circumference. To clamp the xture to a truss:

1. Check that the rigging structure can support at least 10 mes the weight of all xtures and

equipment to be installed on it.

2. Block access under the work area.

3. Working from a stable plaorm, hang the xture on the

truss and fasten the rigging clamps onto the truss.

4. Secure the xture with a safety cable as directed below.

5. Check that the head will not collide with other xtures or objects.

SECURING WITH A SAFETY CABLE

Secure the xture with a safety cable (or other secondary aachment) that is approved for

the weight of the xture so that the safety cable will hold the xture if a primary aachment

fails. Loop the safety cable through and around a secure metal anchoring point.

WARNING! READ SAFETY INFORMATION ON

PAGE 3 BEFORE INSTALLING THE FIXTURE.

7SOLARIS® PIX 72™

Socket outlets or external power switches used to supply the xture with power must be

located near the xture and easily accessible so that the xtures can easily be disconnect-

ed from power.

Do not insert or remove power cable to apply or cut power, as this may cause arcing at the

terminals that will damage the connectors.

Do not use an external dimming system to supply power to the xture, as this may cause

damage to the xture that is not covered by the product warranty.

The xture can be hard-wired to a building electrical installaon if you want to install it

permanently, or a power plug (not supplied) that is suitable for the local power out-lets

can be installed on the power cable.

If you replace power plug on the power cable, install a grounding type (earthed) plug with

integral cable grip that is rated minimum 250 V, 5 A.

The xture has an auto-ranging power supply that accepts AC mains power at 100-240 V

at 50/60 Hz. Do not apply AC mains power at any other voltage or frequency to the xture.

For protecon from electric shock, the xture must be grounded (earthed). The

power distribuon circuit must be equipped with a fuse or circuit breaker and

ground-fault (earth-fault) protecon.

AC POWER

WARNING! READ SAFETY INFORMATION ON

PAGE 3 BEFORE INSTALLING THE FIXTURE.

SOLARIS® PIX 72™ 8

1Tokens® – symbol indicang the xture DMX personality, Beam Angle, Weight and

Power Supply

2Power Connector Input (Built In)

3DMX data Link Input and Output XLR Connectors

4Digital Screen for accessing menu with 4 buons for navigaon: Up, Down Inc (In-

crement) and Dec (Decrement) Enter

UP Press UP to toggle between menu opons

DOWN Press DOWN to toggle between menu opons

INC Press INC to change current value by Incremenng the value displayed by 1

DEC Press DEC to change current value by decremenng the value displayed by 1

FIXTURE OVERVIEW

up down enter esc

9SOLARIS® PIX 72™

DMX DATA LINK

A DMX 512 data link is required in order to control the xture via DMX. The xture

has 3-pin XLR connectors for DMX data input and output. The number of daisy-chained

xtures is limited by the number of DMX channels required by the xtures in relaon to

the maximum 512 channels available in one DMX universe. Note that if independent con-

trol of a xture is required, it must have its own DMX channels.

Fixtures that are required to behave idencally can share the same DMX address and

channels. To add more xtures or groups of xtures when the above limit is reached, add

a DMX universe and another daisy-chained link.

CONNECTING AND USING DMX DATA LINK

To connect the xture to data:

1. Connect the DMX data output from the controller to the rst xture’s male XLR

DMX input connector.

2. Connect the rst xture’s DMX output to the DMX input of the next xture and conn-

ue connecng xtures output to input.

SOLARIS® PIX 72™ 10

FIXTURE OPERATION

This secon explains the xture sengs and ulies that the user has access to when us-

ing the control panel. Sengs are retained when the xture is powered o.

The SOLARIS® PIX 72™ can funcon in dierent modes:

CHANGING DMX CHANNEL MODE Scroll down using the up and down buons below

the digital screen and you will noce that the leer in the beginning changes but the

number 001 persist. (for example “A001” or “E001”) this display changes according to the

mode in which you are operang at that moment. Once you have selected the desired

dmx personality (also known as DMX footprint) Press the enter buon once to access edit

mode and then change the DMX values according to your setup. Oponal values are A001

(2CH mode), C001 (3CH mode), d001 (4CH mode), E001 (6CH mode), H001 (7CH mode),

L001 (12CH mode), P001 (24CH mode),

STANDALONE MODE which allows you to manually change the parameters of the xture

without using DMX data link. When operated in Standalone mode the xture back screen

will show R000 (Led Intensity) when rst accessed. By seng a value between 000-255,

using the up & down buons below the screen, you can control the desired dimmer level.

You can also manually control strobe ashing by changing the values when the back

screen shows FF00 (strobe ash) By seng a value between 01-20, using the up & down

buons below the screen, you can control the desired intensity of strobing.

It is also possible to use 16 predened factory eects, when rst accessing predened

eects back screen will show a value between 1 to 9 followed by the leer “J” for (Jump

eects) or “d” (for gradual eects) and another number between 00-20 (example: “1J09”

or 2d17) when accessed. The number between 1-9 is showing which of the 10 built-in

eects is selected while the number between 01 to 20 following the leer “J” is displaying

the speed of the built in eect. By seng a value from 1 to 9 you can change the pre-

dened built in eect you wish to apply. By seng a value from 01 to 20 you can change

the speed of the predened built in eect you wish to apply.

SOUND TO LIGHT MODE When operated in Sound to Light mode the xture back screen

will show Su00 when rst accessed. By seng a value between 00-20, using the up &

down buons below the screen, you can control The sound eect applied from slow to

fast according to the sound perceived by the unit’s built-in microphone.

Tabla de contenidos

Otros manuales de Equipo de DJ de Solaris

Solaris

Solaris mozart Manual de usuario

Solaris

Solaris SMART 54 Manual de usuario

Solaris

Solaris HITMAN 230 Manual de usuario

Solaris

Solaris basic 18 Manual de usuario

Solaris

Solaris BASIC 90 Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario