Solaris HITMAN 230 Manual de usuario

USER MANUAL

SOLARIS® HITMAN230™ 2

INDEX PAGE NO.

SAFETY INFORMATION 3-4

INTRODUCTION 5

MAXIMIZING LAMP LIFE SPAN 5

INSTALLATION 6-7

AC POWER 7

FIXTURE OVERVIEW 8

DMX DATA LINK 9

CONNECTING AND USING DMX DATA LINK 9

FIXTURE OPERATION 10-11

TOKENS 12

FIXTURE MENU STRUCTURE CHART 13

DMX MODES CHARTS 14-16

MAINTENANCE 17

SMART 180 SPECIFICATIONS 18-19

INCLUDED ITEMS 19

TABLE OF CONTENTS

3SOLARIS® HITMAN230™

WARNING!

Read the safety precauons in this manual before installing

operang or servicing this product.

SAFETY NOTES

Read all the following Safety Notes before working with this product.

These notes include important informaon about the installaon, us-

age, and maintenance of this product.

This product contains no user-serviceable parts. Any reference to ser-

vicing in this User Manual will only apply to properly trained GLOW®

Professional cered technicians. Do not open the housing or aempt

any repairs.

All applicable local codes and regulaons apply to proper installaon of

this product.

PERSONAL SAFETY

· Avoid direct eye exposure to the light source while the product is on.

· Always disconnect this product from its power source before servicing.

· Always connect this product to a grounded circuit to avoid the risk of

electrocuon.

· Do not touch this product’s housing during operaon because it may

be very hot.

MOUNTING & RIG-

GING

· This product is for indoor use only! To prevent risk of re or shock, do

not expose this product to rain or moisture. (IP20)

· Mount this product in a locaon with adequate venlaon, at least 20

in (50 cm) from adjacent surfaces.

· Make sure there are no ammable materials close to this product while

it is operang.

· Always carry this product by the handles. Do not carry from the head.

· When hanging this product, always secure to a fastening device using

a safety cable.

SAFETY INFORMATION

SOLARIS® HITMAN230™ 4

POWER & WIRING

· Always make sure you are connecng this product to the proper volt-

age in accordance with the specicaons in this manual or on the prod-

uct’s specicaon label.

· Never connect this product to a dimmer pack or any rheostat.

· Never disconnect this product

OPERATION

· Do not operate this product if you see damage to the housing, lenses,

LED lights or cables. Have the damaged parts replaced by an authorized

technician at once.

· Do not cover the venlaon slots when operang to avoid internal

overheang.

· Do not aim this product toward the Sun. The lenses could concentrate

the solar energy and cause internal overheang.

· The maximum ambient temperature is 120 °F (49 °C). Do not operate

this product at a higher temperature.

· In case of a serious operang problem, stop using this product imme-

diately

In the unlikely event that your GLOW® product may require service, contact GLOW®

Technical Support.

5SOLARIS® HITMAN230™

The SOLARIS® HITMAN 230™ is a high-performance moving head lighng xture with a

230W HRI 7R 230W lamp. A compact design makes it ideal for Venue Installaons, Theatri-

cal, Cinema, TV and Stage Use.

The xtures features a rotang and indexing gobo wheel with 17 gobos, a color wheel with

14 color lters with Half-Color Capability, high grade smooth mechanical step motors ed

for seamless moving of all the mechanical parts.

The SOLARIS® HITMAN230™ also features a pan\lt feedback, coarse and ne control of

movements and eects. The xture also includes motorized focus and Frost.

The xture can be controlled using any DMX-compliant controller as well as automac oper-

aon mode , sound to light mode and manual mode.

BEFORE USING THE PRODUCT FOR THE FIRST TIME

1. Read ’Safety informaon’ on page 4 before installing, operang or servicing the xture.

2. Unpack and ensure that there is no transportaon damage before using the xture. Never

aempt to operate a damaged xture.

3. If the xture is not going to be hard-wired to a mains supply, aach a local power plug to

the end of the supplied power cable.

4. Before operang, ensure that the voltage and frequency of the power supply match the

power requirements of the xture.

5. Refer to the GLOW® website for the most recent user documentaon and technical infor-

maon about this xture.

MAXIMIZING LAMP LIFE SPAN

To make sure you get the most out of the lamp life span please follow these simple steps:

1. Each me you power the lamp on, allow it to warm up for at least 5 min before shung it

down.

2. Aer the lamp is turned o allow the lamp at least 8 minutes to cool before moving the

xture.

3. Before shung the power completely, power o the lamp but leave power applied to the

xture for a few minutes so that the cooling fans can prevent any momentary temperature

increase caused by heat emied from the other components.

INTRODUCTION

SOLARIS® HITMAN230™ 6

INSTALLATION

The xture is designed for indoor use only and must be used in a dry locaon with adequate

venlaon. Ensure that none of the xture’s venlaon slots are blocked and ensure that the

xture is fastened to a secure structure or surface. Do not use the xture to illuminate sur-

faces less than 8 m (approx 26.) from the xture.

FASTENING THE FIXTURE TO A FLAT SURFACE

The xture can be fastened to a hard, xed, at surface that is oriented at any angle. Ensure

that the surface and all fasteners used can support at least 10 mes the weight of all xtures

and equipment they will support. Fasten the xture Securely. Do not place it on a surface or

leave it where it can be moved or fall over.

If you install the xture in a locaon where it may cause injury or damage if it falls, secure it

as directed below with a securely anchored safety cable that will hold the xture if the pri-

mary fastening method fails.

MOUNTING THE FIXTURE ON A TRUSS

The xture can be clamped to a truss or similar rigging structure in any orientaon. When

installing the xture hanging vercally down, you can use an open-type clamp such as a

G-clamp. When installing in any other orientaon, you must use a half-coupler clamp

that completely encircles the truss or pipe circumference.

To clamp the xture to a truss:

1. Check that the rigging structure can support at least 10 mes

the weight of all xtures and equipment to be installed on it.

2. Block access under the work area.

3. Working from a stable plaorm, hang the xture on the

truss and fasten the rigging clamps onto the truss.

4. Secure the xture with a safety cable as directed below.

5. Check that the head will not collide with other xtures or objects.

WARNING! READ SAFETY INFORMATION ON

PAGE 3 BEFORE INSTALLING THE FIXTURE.

7SOLARIS® HITMAN230™

Socket outlets or external power switches used to supply the xture with power must be

located near the xture and easily accessible so that the xtures can easily be disconnect-

ed from power.

Do not insert or remove power cable to apply or cut power, as this may cause arcing at the

terminals that will damage the connectors.

Do not use an external dimming system to supply power to the xture, as this may cause

damage to the xture that is not covered by the product warranty. The xture can be hard-

wired to a building electrical installaon if you want to install it permanently, or a power

plug (not supplied) that is suitable for the local power out- lets can be installed on the

power cable.

If you replace power plug on the power cable, install a grounding type (earthed) plug with

integral cable grip that is rated minimum 250 V, 5 A.

The xture has an auto-ranging power supply that accepts AC mains power at 100-240 V

at 50/60 Hz. Do not apply AC mains power at any other voltage or frequency to the xture.

For protecon from electric shock, the xture must be grounded (earthed). The

power distribuon circuit must be equipped with a fuse or circuit breaker and

ground-fault (earth-fault) protecon.

AC POWER

WARNING! READ SAFETY INFORMATION ON

PAGE 3 BEFORE SERVICING THE FIXTURE.

SECURING WITH A SAFETY CABLE

Secure the xture with a safety cable (or other secondary

aachment) that is approved for the weight of the xture

so that the safety cable will hold the xture if a primary

aachment fails. Loop the safety cable through and around

a secure metal anchoring point.

SOLARIS® HITMAN230™ 8

1Tokens® – symbol indicang the xture DMX personality, Beam Angle, Weight and Power Supply

2Jog Scrolling Wheel and buon

3Digital Screen for viewing the menu

FIXTURE OVERVIEW

4DMX IN \ DMX OUT

5PowerCon Power In Connector

6T5A Fuse Box

7ON \ OFF Switch

9SOLARIS® HITMAN230™

DMX DATA LINK

A DMX 512 data link is required in order to control the xture via DMX. The xture

has 3-pin XLR connectors for DMX data input and output. The number of daisy-chained

xtures is limited by the number of DMX channels required by the xtures in relaon to

the maximum 512 channels available in one DMX universe. Note that if independent con-

trol of a xture is required, it must have its own DMX channels.

Fixtures that are required to behave idencally can share the same DMX address and

channels. To add more xtures or groups of xtures when the above limit is reached, add

a DMX universe and another daisy-chained link.

CONNECTING AND USING DMX DATA LINK

To connect the xture to data:

1. Connect the DMX data output from the controller to the rst xture’s male XLR

DMX input connector.

2. Connect the rst xture’s DMX output to the DMX input of the next xture and conn-

ue connecng xtures output to input.

SOLARIS® HITMAN230™ 10

FIXTURE OPERATION

This secon explains the xture sengs and ulies that the user has access to when us-

ing the control panel. The SOLARIS® HITMAN230™ can funcon in dierent modes:

DMX 16 CHANNEL MODE. When operated in DMX 16 channel mode the xture screen

will show A001 when rst accessed. By seng a value dierent from 001 you can change

the unit’s DMX address according to your lighng setup. Oponal DMX address values

are 1 to 512. When you reach the desired value, press the Jog Wheel once to save your

changes. Select “Exit” and press once on the jog wheel to return to main menu.

STANDALONE MODE by selecng Run Test Interface opon in the menu you can turn on

Automac Run Mode which will cause the xture to execute its built-in macro eects one

by one. Simply select Run Test interface by using the Jog Wheel to posion the selecon

marker and press the jog wheel once to enter the sub menu, then scroll down, using the

jog wheel again, unl the selecon shows “Auto Run” - select this opon by clicking the

jog wheel once and select “ON” than press exit to return to the main display screen. by

seng this opon to “OFF” the xture will exit auto run mode and return to DMX control

mode. Select “Exit” and press once on the jog wheel to return to main menu.

SOUND TO LIGHT MODE by selecng Run Test Interface opon in the menu you can

turn on Sound Run Mode which will cause the xture to execute its built-in macro eects

one by one according to the sound picked-up by the xture’s built-in microphone. Sim-

ply select Run Test interface by using the Jog Wheel to posion the selecon marker and

press the jog wheel once to enter the sub menu, then scroll down, using the jog wheel

again, unl the selecon shows “Sound Run” - select this opon by clicking the jog wheel

once and select “ON” then press exit to return to the main display screen. by seng this

opon to “OFF” the xture will exit sound run mode and return to DMX control mode.

Select “Exit” and press once on the jog wheel to return to main menu.

THE SETUP INTERFACE using the setup interface you may change the operaon of the

xture in the following ways:

X Reverse - by seng this opon to “ON” the xture will reverse its pan aributes. by de-

fault this seng is set to “OFF”

Y Reverse - by seng this opon to “ON” the xture will reverse its lt aributes. by de-

fault this seng is set to “OFF”

Lamp On - by seng this opon to “ON” the xture will turn on the lamp. by seng this

opon to “OFF” the xture will turn-o its lamp. by default this seng is set to “ON”,

Tabla de contenidos

Otros manuales de Equipo de DJ de Solaris

Solaris

Solaris PIX 72 Manual de usuario

Solaris

Solaris basic 18 Manual de usuario

Solaris

Solaris SMART 54 Manual de usuario

Solaris

Solaris mozart Manual de usuario

Solaris

Solaris BASIC 90 Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario