Socket CHS 7Mi Manual de usuario
Model shown: CHS 7Mi
Bluetooth Barcode Scanner
CHS 7Mi, 7Pi
www.socketmobile.com
SerieS 7
1D LASER QUICKSTART GUIDE
PACKAGE CONTENTS PRODUCT INFORMATION
© 2010-2015 Socket Mobile, Inc. All rights reserved. Socket, the Socket logo, and
SocketScan are registered trademarks or trademarks of Socket Mobile, Inc. The Bluetooth
word mark and logo are registered trademarks of the Bluetooth SIG, Inc. USA, and any
use by Socket Mobile, Inc. is under license. All other trademarks and trade names
contained herein may be those of their respective owners.
CHS Series 7 AC adapter* & USB
to DC plug cable
*Use the plug that is region-
ally appropriate
Lanyard NiMH
rechargeable
batteries
*Also used for keyboard Pop-up (HID Mode only)
Twist-lock
(horizontal/unlocked)
Battery door
Twist-lock
(vertical/locked)
Lanyard
Blue/Green/Red
LED
Trigger button
Power button*
DC-in connector
Scanner head
Product label
Thank you for choosing Socket Mobile!
Let’s get started!
Pins for
charging
cradle
mobile
®
mobile
®
mobile
®
mobile
®
mobile
®
mobile
®
mobile
®
mobile
®
mobile
®
3
SCANNER SETUP
Insert the Batteries
Unlock the Battery door by us-
ing a thin coin to turn the lock
under the CHS to a horizontal
position (turn 90 degrees).
Install the batteries in their correct po-
sition as indicated by the +/- symbols.
Important: Only use NiMH
Rechargeable batteries. Do
NOT use Alkaline Batteries
Attach the Lanyard (optional)
Detach the string loop of the
tether from the lanyard. Then
feed the string loop through the slot
in the Twist-lock and then through the
end of the loop. Pull tight so the string
loop is secure to the Twist-lock, Reat-
tach the string loop to the tether from
the Lanyard.
If desired, attach the tether to a lan-
yard or belt.
CHARGE THE BATTERY
Charge the CHS
The CHS must be fully charged be-
fore rst use. Please allow 5 hours
uninterrupted charging for the
initial battery charge.
For the 7Pi, lift the rubber ap to access
the power connector.
• Red LED = Charging
• Green LED = Fully charged
Charging from a computer USB port
is not reliable and not recommended.
Socket Mobile offers a Charging Cradle (op-
tional Accessory/sold separately) which is a
convenient holder that charges the scanner
when not in use.
Cradle Sku#
CHS 7Mi: AC4054-1381
CHS 7Pi: AC4055-1382
45
BASIC FUNCTIONALITY
•Powering On:
Press and hold down the small
power button until the LED
turns blue and the CHS beeps
twice (low-high).
•Powering Off/ Disconnecting:
Press and hold down the small
power button until the CHS beeps
twice (high-low).
BASIC FUNCTIONALITY (CONTINUED)
Scanning Barcodes:
After connecting the CHS to your device, open an application and put
the cursor where you want to enter data.
Hold the CHS about 4 inches (10 cm) from the barcode and press and
hold the trigger button. Keep your hand steady and make sure the
Red beam covers the entire width of the barcode.
By default, the CHS will beep and vibrate, and the LED will ash
Green to conrm that data was decoded and sent to the device.
Not recommended
scanning techniques
Aim the scan beam straight
across the entire barcode.
Power button
6 7
CONNECTION MODES (CONTINUED)CONNECTION MODES
HID Keyboard Emulation mode (default)
In HID mode the CHS emulates a keyboard. This is a universal connec-
tion method and will work with any application that has a text eld.
The application receives the data input from the CHS. The CHS includes
a keyboard pop-up feature so you can disable the CHS and accept data
input from the onscreen keyboard on the device. Pages 10-11 provides
the connection steps using HID mode.
SerialPortProle(SPP)
Highly recommended, allows two-way communications with Apple iOS
devices. Compatible application developed with SocketScan 10 SDK
required.
MAC OS devices are connected using HID mode.
iOS devices are connected using either iOS mode or HID mode, but
not both together.
98
The CHS is connected to your iOS device using one of the following
modes:
1. iOS mode
2. HID Keyboard Emulation mode (default)
3. Serial Port Prole (SPP)
iOS mode
iOS mode is used with a Scanner-enabled Application. Scanner controls
are embedded in the Application to provide better performance, secu-
rity, features, and domain-specic capabilities.
If you purchased a Scanner-enabled Application on the Apple App Store
(or through the Apple Volume Purchase Program for Business) that
features integrated support for the CHS, we recommend you install that
Application on your device and follow the Application instructions to
connect with the CHS. If the connection steps are not documented in
the Application, please see pages 12-13 for the connection steps using
iOS mode.
Please visit the Socket Mobile App Store to conrm your Scanner-en-
abled Application supports the CHS.
www.socketmobile.com/appstore
HID (KEYBOARD EMULATION) MODE HID (KEYBOARD EMULATION) MODE (CONTINUED)
10
To pair the CHS with the Apple device in HID mode: (required only the
rst time you connect).
1. Power on the CHS.
2. Turn Bluetooth on for the Apple device. Go to Settings > Bluetooth. A
Bluetooth Devices search will begin.
An iOS device is always Discoverable when the Bluetooth menu
is active. A MAC OS device provides an option to turn Discover-
able On or Off. Conrm the MAC OS device is Discoverable.
3. Tap Socket CHS[xxxxxx] in the list of Devices found. After a few sec-
onds the “Not Paired” status will change to “Connected” and the CHS
Blue LED will blink every 3 seconds indicating it is Connected.
The characters in brackets are the last 6 characters of the
Bluetooth Address. The full Bluetooth address is printed in the
Product Label (remove the battery door).
You are now ready to scan barcodes, see instructions on page 7.
11
Keyboard Pop-up Enable
The CHS emulates the keyboard in HID mode. So scanned barcode data
will be input into the text eld. The following steps show how to access
the onscreen keyboard while connected to the CHS in HID mode.
1. Make sure the CHS is connected to your Apple device in HID mode.
2. Open your application and place the cursor where you want to enter
data.
3. Quickly double-press the power button of the CHS (like double-
clicking a mouse) to open or close the onscreen keyboard. The CHS
will beep once as conrmation.
To connect to a new Apple device, you must rst unpair the CHS
and remove the CHS from the Bluetooth list in your device. See
page 15.
iOS MODE - SCANNER-ENABLED APP iOS MODE - SCANNER-ENABLED APP (CONTINUED)
If you are using a Scanner-enabled Application, follow their instructions
to connect with the CHS. Many applications include these steps and
barcodes in the set-up procedure.
If you are using an Application that connects to the CHS using HID
Keyboard Emulation mode, follow the instructions on pages 10-11. iOS
mode should not be used.
If you are using the CHS with an iOS device and a Scanner-enabled
Application that does not provide instructions to connect with the CHS,
please use the following steps.
1. Power on the CHS and scan this barcode. The CHS will beep 3 times.
Print page to scan.
Do not scan onscreen.
12
2. Turn Bluetooth on for the Apple device. Go to Settings > Bluetooth. A
Bluetooth Devices search will begin.
3. Tap Socket CHS[xxxxxx] in the list of Devices found. After a few
seconds the “Not Paired” status will change to “Connected” and the
CHS Blue LED will blink every 3 seconds conrming the connection.
The characters in brackets are the last 6 characters of the
Bluetooth Address. The full Bluetooth address is printed in the
Product label (remove the Battery door).
4. Open the Scanner-enabled Application. The CHS will beep once
indicating that the application is in control and you are ready to scan.
It should now be connected to the CHS.
You are now ready to scan barcodes with the Scanner-enabled
Application, see instructions on page 7.
13
ANDROID - SERIAL PORT PROFILE (SPP) ANDROID - SERIAL PORT PROFILE (SPP)
14 15
The instructions below are based on the Asus Nexus 7 running
Android OS 4.2. Instructions for other devices may slightly differ.
For Bluetooth HID instructions, please see the User’s Guide.
To install the software:
1. If you installed barcode scanning software for your device camera,
you can scan this barcode to launch the SocketScan 10 page in Google
Play. Alternatively, open Google Play and search for SocketScan 10
Keyboard Wedge software using the keyword “Socket”.
2. Follow the on-screen instructions to download and install SocketScan
10 software using the keyword “Socket”.
If prompted, allow the app to access Bluetooth settings / USB storage
/ SD card contents.
3. If SocketScan 10 prompts you to turn on Bluetooth, touch Allow.
4. You will be prompted to set SocketScan 10 as the keyboard language.
Touch Back .
5. Touch Home | Apps | Settings | Language & input.
6. Under Keyboard & Input Methods, select SocketScan 10. In the same
settings you can congure the keyboard language or congure the
volume up button to trigger a scan. Touch Back.
Note: You can also trigger the scanner using the volume up button.
7. In SocketScan 10, touch Menu | Input Method. Select SocketScan 10.
Touch Back.
To pair and connect the CHS to Android device: (required only the rst
time you connect).
1. Power on the CHS and scan this barcode to put the CHS in SPP mode.
The CHS will beep 3 times.
Print page to scan.
Do not scan onscreen.
2. In SocketScan 10, touch Menu | Socket EZ Pair. Touch Bluetooth.
3. Select Socket CHS [xxxxxx].
ANDROID - SERIAL PORT PROFILE (SPP) WINDOWS - SERIAL PORT PROFILE (SPP)
16 17
The characters in brackets are the last 6 characters of the
Bluetooth Address, which is labeled in the CHS battery
compartment.
4. When notied of a pairing request, swipe the notication down.
Touch Pairing request. Touch Pair.
5. After the CHS connects and is ready to scan barcodes, it will beep
once. The icon at the top of the screen will also change (see below).
Touch Back.
6. A CHS registration icon will also appear on top of the screen. If
desired, swipe it down to open the software and register your CHS.
Now you are ready to scan barcodes, see instructions on page 7.
To connect to a new device, you must rst unpair the CHS. See
page 15.
ToinstallthesoftwareandcongureaCOMport:
Windows 7/8: Make sure you have administrative privileges to
install software.
1. Download the latest SocketScan 10 software from: http://www.
socketmobile.com/support/downloads/data-collection/series7/
ss10/?page=series7.
2. Follow the on-screen instructions to install the software. In the last
screen, click Finish.
3. In SocketScan Settings, select an incoming Bluetooth serial COM port.
Click OK.
Click Ports to create a new incoming COM port or identify an
incoming COM port.
1. To pair the CHS with the PC: (required only the rst time you
connect)Power on the CHS and scan this barcode. It will beep 3
times.
Print page to scan. Do not scan onscreen.
2. Use your Bluetooth software to start a device search.
WINDOWS - SERIAL PORT PROFILE (SPP) WINDOWS - HID (PERIPHERALS) MODE
18 19
3. Select Socket CHS [xxxxxx]. If prompted for a passkey, enter 0000
(four zeroes).
The characters in brackets are the last 6 characters of the CHS
Bluetooth Address, which is labeled in the CHS battery
compartment.
If prompted, choose Socket Serial Port service. Select an available
COM.
4. Make sure SocketScan 10 is running. Click on the SocketScan 10
desktop icon.
5. Click on the SocketScan 10 icon in the task tray. In the pop-up
menu, click Socket EZ Pair. Click Bluetooth. Select your CHS and click
Pair.
6. The PC will connect to the CHS, indicated by a beep. The CHS will
then disconnect from the computer, indicated by two beeps. Click
OK.
7. After the CHS connects and is ready to scan barcodes, it will beep
once. The task tray icon will also change (see below).
8. Close Socket EZ Pair. The Registration screen will appear. If desired,
register your CHS.
Now you are ready to scan barcodes, see instructions on page 7.
To pair the CHS with the PC: (required only the rst time you connect)
1. Power on the CHS and scan this barcode. The CHS will beep 3 times.
Print page to scan.
Do not scan onscreen.
2. Turn on Bluetooth on your PC or PDA and start a device search.
3. Select Socket CHS [xxxxxx]. If prompted for a passkey, enter 0000
(four zeroes). If prompted to select services, select Input Device.
4. After the CHS connects and is ready to scan barcodes, it will beep
once.
Now you are ready to scan barcodes, see instructions on page 7.
To connect to a new device, you must rst unpair the CHS. See page 23.
Otros manuales para CHS 7Mi
3
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Lector de código de barras de Socket
Socket
Socket CHS 7Ci Manual de usuario
Socket
Socket CHS Series 7 Manual de usuario
Socket
Socket CHS 7Ci Manual de usuario
Socket
Socket CHS 7Ci Manual de usuario
Socket
Socket CHS Series 7 Manual de usuario
Socket
Socket Socketscan S370 Hoja de especificaciones
Socket
Socket SOCKETSCAN S800 Manual de usuario
Socket
Socket DuraSled DS800 Series Manual de usuario
Socket
Socket CompactFlash Scan Card Series 5 Manual de usuario
Socket
Socket CHS Series 7 Manual de usuario
Socket
Socket SOCKETSCAN 800 Series Manual de usuario
Socket
Socket CHS 7Mi Manual de usuario
Socket
Socket CHS 7Ci Manual de usuario
Socket
Socket 7 Series Manual de usuario
Socket
Socket DURASCAN D740 Manual de usuario
Socket
Socket D820 Manual de usuario
Socket
Socket 5 Series Manual de usuario
Socket
Socket SocketScan S700 Manual de usuario
Socket
Socket Cordless Ring Scanner Series 9 Manual de usuario
Socket
Socket CHS 7Xi Manual de usuario
