Smeg ECF01 Manual de usuario
Description
9
ENITEN
2 Description
2.1 Product Description
Model ECF01 - Espresso Machine
1 Cup warmer tray
2 Grouphead
3 Filter holder
4 Steel cup tray
5 Floater
6 Stainless steel drip tray
7 Hot water and steam wand/Cappuccino
frother
8 Steam valve
9 ON/OFF switch
10 Water tank cover
11 Water tank (1 liter)
12 Measuring scoop/tamper
13 Soft pod filter basket
14 1-cup ground coffee filter basket
15 2-cup ground coffee filter basket
16 Water softener filter (optional)
17 1-cup coffee button (white light)
18 2-cup coffee button (white light)
19 Steam button (white light)/Descaler
button (orange light)
20 Non-slip feet
17 18 19
3
1
15
5
4
2
14
13
6
12
20
11
8
10
16
16
7
9
Use
10
3 Use
3.1 Before first use
1. Remove any labels and stickers from the
espresso machine.
2. Thoroughly wash and dry the espresso
machine’s parts (see “4 Cleaning and
maintenance”).
3. Remove the cover (1) by pulling it
upwards and then pull out the tank (2).
4. Fill the tank (2) with fresh, clean water
directly from the faucet or by using a
pitcher, being careful not to exceed the
maximum level indicated on the tank.
1
2
Risk of accident
• Do not operate the espresso machine
without water in the tank or without the
tank in place.
The parts that may come into
contact with food are made of
materials that comply with all legal
provisions in force.
2
Use
11
ENITEN
3.2 First use
1. Turn on the espresso machine using the
ON/OFF switch (1): the lights of the
three buttons (2), (3) and (4) will flash in
sequence.
2. Lights (2) and (3) will flash to indicate
that the machine is reaching the pre-set
temperature. The espresso machine is
ready for use as soon as the lights stop
flashing.
3. Place a container under the hot water/
steam wand (4).
4. Turn the steam valve (5) to the
position and dispense 1/2 cup of water.
5. Turn the steam valve (5) back to the
position.
6. Attach the filter holder by aligning the
handle with and turning it to the
right to the position.
7. To rinse the machine’s internal circuits,
place a container under the coffe spout
and press the button.
8. Repeat this procedure 5 times.
2 3 4
1
Make 4-5 espressos or 4-5
cappuccinos to obtain a
satisfactory result.
4
5
Use
12
Then proceed with rinsing the “steam”
circuit:
9. Place a container under the hot water
spout and turn the steam valve to the
position. Hot water is delivered.
10. When the appliance automatically
stops the hot water delivery, turn the
steam valve back to the position.
11. Repeat this procedure 1 more time (if
necessary, refill the tank).
Filters
The coffee machine comes with three filters:
a one-cup filter, a two-cup filter, and a soft
pod filter. Below each filter you will find the
corresponding symbol.
3.3 How to make espresso
Ground coffee:
1. Place the ground coffee filter basket (1)
in the filter holder (2), choosing the one-
cup or the two-cup basket.
2. Tamp the ground coffee down using the
tamper (3).
1
2
3
3
Use
13
ENITEN
3. Wipe off any excess ground coffee
from the edge of the filter holder.
Attach the filter holder by aligning the
handle with and turning it to the
right to the position.
4. Place the cup or cups under the filter
holder spouts and press the coffee
button or .
• For one cup, fill the filter basket
with one level scoop of coffee
(about 1 tablespoon.)
• For two cups, fill the filter basket
with two scoops of coffee.
• For a stronger coffee, tamp the
ground coffee hard with the
tamper.
• For a weaker coffee, use the
tamper to tamp the ground
coffee lightly.
Risk of scalding
• To avoid any splashing, do not detach
the filter holder while coffee is being
dispensed. Wait a few seconds for the
process to finish.
After the machine has not been
used for a while (more than 30
minutes) it is normal for the first
cups of coffee not to be at the right
temperature.
The recommendations for
obtaining a hot coffee immediately
are shown in section “4.5 What to
do if...”
Use
14
Coffee soft pods:
1. Insert the coffee soft pod filter basket
in the filter holder.
2. Insert the soft pod in the filter holder trying
to center it as much as possible.
3. Proceed in the same way as with ground
coffee.
3.4 How to make cappuccino
1. Make an espresso in a large cup.
2. Press the button: the light will flash.
3. Fill a container with 1/2 cup cold,
partially skimmed milk for each
cappuccino you want to make.
4. When the light stops flashing, place
an empty container under the
cappuccino frother (1) and turn the
steam valve (2) to the position to
drain any water present and then close
the valve.
5. Place the container with the milk under
the cappuccino frother (1), immersing the
cappuccino frother a few millimeters
below the surface. Turn the steam valve (2)
to the position and slowly move the
container up and down to obtain a
creamier foam.
Risk of scalding
• To avoid any splashing, do not detach
the filter holder while coffee is being
dispensed. Wait a few seconds for the
process to finish.
• The process can be interrupted
at any time by pressing the coffee
button.
• To increase the amount of coffee
in the cup, hold down the coffee
button.
1
2
Use
15
ENITEN
6. Once the volume of the milk has
doubled, dip the cappuccino frother
deep into the milk and heat to 140°F
(60°C). Stop the frothing process by
turning the steam valve clockwise.
7. Pour the milk into the cups with the
espresso.
3.5 How to heat water
1. Turn the machine on using the ON/OFF
switch.
2. Place a container under the cappuccino
frother.
3. Turn the steam valve to the position
to let the hot water out.
3.6 Accessing the programming
menus and changing the settings
1. Make sure that the machine is ready to
use and hold the button for 10
seconds until the three buttons start
flashing: the machine will enter
programming mode.
2. Program the machine settings to your
own needs.
3. To exit the menu, simply do not press any
button for 15 seconds.
• To make more than one
cappuccino, first prepare all the
espresso and then froth the milk
for all the cappuccinos.
• For hygiene reasons, it is
recommended to clean the
cappuccino frother after use.
• Clean out the milk residue by
opening the steam valve to let out
the steam.
• Release the steam for only a
maximum of 60 seconds.
• Release the steam for only a
maximum of 60 seconds.
Use
16
Setting the coffee temperature
1. Access the programming menu.
2. Press the button to select the
temperature of the coffee. The lights of
the current setting will turn on:
3. The lights will start flashing in sequence.
4. Press the button corresponding to the
desired temperature: low ,
medium or high .
5. The button will flash to indicate the
selection has been saved.
Setting the amount of coffee
To change the quantity of coffee dispensed
by the machine:
1. Place one or two cups under the filter
holder spouts.
2. Press the button for one cup or two
cups and hold it down.
3. The machine will start dispensing coffee.
4. Release the button as soon as you reach
the desired amount of coffee.
5. The light will flash to indicate that the
selected quantity has been saved.
Setting the water hardness
1. Access the programming menu.
2. Press the button to select the water
hardness. The lights of the current setting
will turn on:
3. The lights will start flashing in sequence.
4. Press the button corresponding to the
water hardness:
5. The button will flash to indicate the
selection has been saved.
Lights Temperature setting
Low
Medium
High
Lights Water setting
Soft
Medium
Hard
soft medium hard
<10°dH 10°dH - 20°dH > 20°dH
<18°fH 18°fH - 36°fH > 36°fH
< 180 mg/l
CaCo3
180-300 mg/l
CaCo3
360 mg/l
CaCo3
Use
17
ENITEN
Setting the auto shut-off time
For energy saving reasons, the espresso
machine is equipped with an auto shut-off
feature that activates when the machine has
been left on for a long time.
To set the auto shut-off time:
1. Access the programming menu.
2. Press the button to select the auto
shut-off time. The lights of the current
setting will turn on:
3. The lights will start flashing in sequence.
4. Press the button corresponding to the
time you want to set, choosing from 9
minutes , 30 minutes or 3
hours .
5. The button will flash to indicate the
selection has been saved.
Restoring the factory settings
To restore factory settings:
1. Access the programming menu.
2. Turn the steam valve to the position.
3. Press the button: the three lights will
blink to indicate that the original settings
have been restored.
4. Turn the steam valve back to the
position.
Lights Time setting
9 minutes
30 minutes
3 hours
Use
18
3.7 How to cool down the boiler
The boiler must be cooled down if you want
to make coffee immediately after frothing
milk for cappuccino.
If the boiler is not cooled down, the coffee
will be burned.
1. Place a container under the cappuccino
frother and open the steam valve to
dispense hot water.
2. The hot water will stop coming out as
soon as the machine has cooled down.
3. Close the steam valve and proceed with
making the coffee.
Otros manuales para ECF01
3
Tabla de contenidos
Otros manuales de Cafetera de Smeg
Smeg
Smeg CMS6451X Manual de usuario
Smeg
Smeg BCC01EGMEU Manual de usuario
Smeg
Smeg DCF02BLUS Manual de usuario
Smeg
Smeg BCC02 Manual de usuario
Smeg
Smeg ECF02 Manual de usuario
Smeg
Smeg DCF02PBUS Manual de usuario
Smeg
Smeg EGF03PGUS Manual de usuario
Smeg
Smeg CMSC451 Manual de usuario
Smeg
Smeg BCC02 Manual de usuario
Smeg
Smeg ECF01 Manual de usuario
Smeg
Smeg BCC01 Manual de usuario
Smeg
Smeg Classica CMS4303X Manual de usuario
Smeg
Smeg CMS4601NR Manual de usuario
Smeg
Smeg 50's style Manual de usuario
Smeg
Smeg BCC01 Manual de usuario
Smeg
Smeg BCC01WHMUS Manual de usuario
Smeg
Smeg CMSCU451S Manual de usuario
Smeg
Smeg BCC13EGMEU Manual de usuario
Smeg
Smeg BCC02WHMAU Manual de usuario
Smeg
Smeg EGF03 Manual de usuario
