Smeg Dolce Stil Novo CMS4101S Manual de usuario

Consigli e suggerimenti per un perfetto allineamento

Tips & tricks for a perfect alignment

DOLCE STIL NOVO

This installation manual is accompanied by a

demonstration video that can be viewed at:

www.youtube.com/user/SmegSpA

Positioning the products

in 45 cm high recesses

Positioning the products

in 60 cm high recesses

24 25

If the DOMESTIC APPLIANCES are to be INSTALLED IN 60 CM HIGH RECESSES:

1. Make sure that the unit is squared and level the support bases. (Fig. 1)

2. Make sure that the individual shelves are perfectly horizontal. (Fig. 1)

3. If there is a 60 cm oven in the composition, this should be the rst product to

be inserted, centred and fastened to the unit. (Fig. 2).

4. If there is not a 60 cm oven in the composition, but there is a 45 cm oven

plus a drawer, these should be the rst products to be inserted, centred and

fastened to the unit (Fig. 3).

INSTALLATION - Products in 60 cm high recesses

Fig. 2

Fig. 1

Fig. 3

IMPORTANT

IMPORTANT:

-Insert all the drawers into remaining recesses, level them and align the

lower trims with the lower trim of the 60 cm oven (Fig.4).

-The height of the front glass of the drawer can be regulated by adjusting

the screws (Torx insert screws) inside the drawer (loosen the screws, adjust the

height and retighten the screws). (Fig. 4)

Fig. 4

26 27

5. Make sure that the drawers are ush with the door of the oven. If necessary,

carry out the following adjustments:

-Use a 5 mm hex wrench to regulate the drawer fastening mechanism. Turn

it clockwise to move the drawer outwards, turn it anticlockwise to move the

drawer inwards (Fig. 5)

-If the left or right hand sides of the front of the drawer are not perfectly

ush, place a shim behind the drawer support bracket to compensate for any

differences.

Fig. 5

Fig. 5A

IMPORTANT:

-After adjustment is complete, fasten the drawer to the unit using the side

screws and then install the covers (Fig. 5A).

INSTALLATION - Products in 60 cm high recesses

6. Insert the rst 45 cm product next to 60 cm oven that has already been

installed.

• 45 cm Oven:

Align the upper trims of the ovens. If necessary, place shims* under the oven

(Fig. 6) to compensate for any misalignment. Lastly, secure the product using the

screws (Fig. 7)

Fig. 6

Fig. 7

* shims not supplied

28 29

• Coffee machine:

If the width of the recess is 560 mm: there is no need to place shims behind the

plate of the guides. (Fig. 8)

If the width of the recess is 562 mm place the 1 mm shims provided behind the

plates of the guides. (Fig. 8)

If the width of the recess is 564 mm place the 2 mm shims provided behind the

plates of the guides. (Fig. 8)

Place the runners on the casing of the drawer whilst keeping them ush with the

side of the unit.

Fix the brackets with the runners to the unit using 2 screws in the slotted holes.

(Fig. 9)

Fig. 8

Fig. 9

INSTALLATION - Products in 60 cm high recesses

Make sure that it is aligned horizontally with the other products and the drawer

(make sure that the gap between the coffee machine and the drawer is

uniform). If necessary, place a shim under one or both brackets. (Fig. 11)

Fasten it in place using all the screws only after the front of the machine has

been correctly aligned. (Fig. 12)

Fig. 10

Pull out the runners and place the coffee machine on them. (Fig. 10)

30 31

Fasten the brackets using all the necessary screws.

Fig. 11

Fig. 12

INSTALLATION - Products in 60 cm high recesses

7. Adjust the hinges of the doors around the products in order to make the gaps

uniform.

•Wine cooler:

Place the wine cooler on the drawer and check its horizontal alignment.

If necessary, place shims* under the feet of the wine cooler. (Fig. 13)

Fasten the wine cooler using the screws. (Fig. 14)

Fig. 13 Fig. 14

* shims not supplied

32 33

INSTALLATION - Products in 45 cm high recesses

If the DOMESTIC APPLIANCES are to be INSTALLED IN 45 CM HIGH RECESSES:

1. Make sure that the unit is squared and level the support bases. (Fig. 1)

2. Make sure that the individual shelves are perfectly horizontal. Otherwise, any

misalignment must be corrected after the product has been inserted. (Fig. 1)

3. If there is a 45 cm oven in the composition, this should be the rst product to

be inserted, centred and fastened to the unit. (Fig. 2)

Fig. 1

Fig. 2

4. Insert the second product next to 45 cm oven that has already been installed:

• 45 cm Oven:

Align the upper trims of the ovens. If necessary, place shims* under the oven to

compensate for any misalignment.

Lastly, secure the product using the screws (Fig. 3)

Fig. 3

* shims not supplied

34 35

• Coffee machine:

If the width of the recess is 560 mm: there is no need to place shims behind the

plate of the guides. (Fig. 5)

If the width of the recess is 562 mm place the 1 mm shims provided behind the

plates of the guides. (Fig. 4)

If the width of the recess is 564 mm place the 2 mm shims provided behind the

plates of the guides. (Fig.4)

Place the runners on the shelf of the unit whilst keeping them ush with the side

of the unit.

Fix the brackets with the runners to the unit using 2 screws in the slotted holes.

(Fig. 5)

Fig. 4

Fig. 5

INSTALLATION - Products in 45 cm high recesses

Make sure that it is aligned horizontally with the other products. If necessary,

place a shim* under one or both brackets. (Fig. 7)

Fasten it in place using all the screws only after the front of the machine has

been correctly aligned. (Fig.8)

Fig.6

Pull out the runners and place the coffee machine on them. (Fig. 6)

36 37

Fasten the brackets using all the necessary screws.

Fig. 7

Fig. 8

* shims not supplied

INSTALLATION - Products in 45 cm high recesses

5. Adjust the hinges of the doors around the products in order to make the gaps

uniform.

•Wine cooler:

Insert the product in the unit and centre it. Make sure that the upper trims of

adjacent products are aligned. If necessary, place shims under the feet of the

wine cooler (Fig. 9) to compensate for any misalignment.

Lastly, secure the product using the screws. (Fig. 10)

Fig. 9 Fig. 10

* shims not supplied

Este manual sirve para los siguientes modelos

Otros manuales de Cafetera de Smeg

Manuales populares de Cafetera de otras marcas

Taurus

Taurus Livorno 6 Manual de usuario

Delta-q

Delta-q QUICK Manual de usuario

Bunn

Bunn LCA-1 Guía de solución de problemas

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Instrucciones de instalación

Saeco

Saeco Vienna Plus Sup 018M Manual de usuario

DeLonghi

DeLonghi DC300 Manual de usuario

INCAPTO

INCAPTO BXCO1470E Manual de usuario

Bosch

Bosch TASSIMO finesse TAS16B Series Manual de usuario

Exido

Exido 245-072 Manual de usuario

Animo

Animo OptiVend Choco Manual de usuario

Siemens

Siemens TQ505DF Series Manual de usuario

DeLonghi

DeLonghi ECI341 Manual de usuario

Krups

Krups KT406511 Manual de usuario

Cimbali

Cimbali M32 Classic Manual de usuario

Philips

Philips HL3844N Manual de usuario

Bosch

Bosch TES 515 SERIES Manual de usuario

Tekmatix

Tekmatix TMFM - 65 Manual de usuario

Scarlett

Scarlett SC-CM33005 Manual de usuario