SMC Networks WAP3110-L Manual de usuario

– 1 –

Quick Start Guide

IEEE 802.11b/g/n Enterprise Access Point

WAP3110-L

The WAP3110-L is a IEEE 802.11b/g/n access point (AP) that is designed to deliver

high-performance wireless services for clients in an enterprise environment.

Housed in a compact enclosure, the unit includes its own built-in options for

mounting on a wall, or suspended ceiling T-rail. The unit can be powered through a

PoE cable connection from a PoE network switch, or from its AC power adapter.

In addition, the AP supports network management from an SMC WAC4502 wireless

access controller throught the Control and Provisioning of Wireless Access Points

(CAPWAP) protocol.

OTE

For detailed access point (AP) installation information, refer to the

Installation Guide,which is on the Documentation CD included with the AP.

OTE

For Safety and Regulatory information, refer to the Safety and Regulatory

Information document included with the AP.

The AP includes its own built-in features for mounting the unit to a wall or

suspended ceiling T-rail.

Caution:

The planning and installation of the AP requires professional personnel

that are trained in the installation of radio transmitting equipment. The user is

E042013-AP-R01

www.smc.com

Quick Start Guide

– 2 –

responsible for compliance with local regulations concerning items such as

antenna power, use of lightning arrestors, grounding, and radio mast or tower

construction. Therefore, it is recommended to consult a professional contractor

knowledgeable in local radio regulations prior to equipment installation.

Follow these steps to install the AP:

1. Unpack the AP Unpack the AP and check the package contents.

◆WAP3110-L Enterprise Access Point

◆AC Power adapter

◆Console cable (RJ-45 to DB-9)

◆Quick Start Guide (this guide)

◆Regulatory and Safety Information

◆Documentation CD — includes Installation Guide

2. Mount the AP After planning your installation, mount the unit on a wall or suspended ceiling

T-rail.

Mounting on a Wall

Set two screws in the wall 6.2 mm (2.4 in.) apart.

Slide the AP’s wall mounting slots down onto the screws so that the unit is secure.

Quick Start Guide

– 3 –

3. Connect Cables Connect network cable to the RJ-45 port for your network connection. The RJ-45

port connection can also provide PoE power to the unit.

Mounting on a Ceiling T-rail

Position the AP’s ceiling-mount clip holders on either side of the T-rail.

Turn the AP until the two clips lock the AP to the T-rail.

Connect Category 5e or better cable to the RJ-45 port.

Quick Start Guide

– 4 –

4. Connect Power If you do not power the unit using PoE, connect the AC power adapter to the AP

and to an AC power source.

5. Verify AP Operation Verify basic AP operation by checking the system LEDs.

The Power LED should be on green and the Network LED on or flashing amber.

Connect the power adapter to the power socket.

Connect the power adapter to a nearby AC power source.

Network Link/Activity

Power/Diagnostic

Quick Start Guide

– 5 –

6. Connect to the

Console Port

To make initial configuration changes to the AP, connect a PC to the AP’s console

port using the included console cable.

From a PC running VT-100 terminal emulator software, use the following settings:

◆Baud rate — 115,200 bps

◆Character Size — 8 Characters

◆Parity — None

◆Stop bit — One

◆Data bits — 8

◆Flow control — none

◆Login Name — admin

◆Password — null (there is no default password)

For information on manually configuring an IP address for the AP, refer to the

Installation Guide, which is on the Documentation CD included with the AP.

For further information on AP configuration and CLI commands, refer to the

Management Guide, which is on the Documentation CD included with the AP.

Console Port

Quick Start Guide

– 6 –

Hardware Specifications

Item Specification

Chassis Specifications

Size W x D x H: 140 x 140 x 47.8 mm (5.51 x 5.51 x 1.88 inches)

Weight 500 g (1.10 lbs)

Temperature Operating: 0 °C to 40 °C (32 °F to 104 °F)

Storage: -20 °C to 70 °C (-4 °F to 158 °F)

Humidity Operating: 5% to 95% (non-condensing)

Network Interfaces

Ports One RJ-45 Port: 1000BASE-T, PoE (PD)

2.4GHz Radio IEEE 802.11b/g/n

Radio Frequencies 2400 ~ 2483.5 MHz

2412 ~ 2472 MHz

Power Supply Specifications

PoE Input Power 48 VDC, 0.3A

AC Power Adapter AC Input: 100 ~ 240 VAC

DC Output: 12 VDC, 2 A

Power Consumption 22.5 W maximum

Regulatory Compliances

Radio ETSI 300 328 (802.11b/g)

ETSI 301 893 (802.11a Full range)

ETSI 301 489 (DC power)

FCC Part 15C 15.247/15.207 (2.4-2.4835GHz)

NCC LP0002 (2.4-2.4835GHz)

Emissions EN 55022:2007, Class A/B

IEC 61000-3-2/3

FCC Class B Part 15

CNS13438

Immunity EN 55024:2001 + A2:2003

IEC 61000-4-2/3/4/5/6/8/11

Safety CSA c us (CSA/UL60950-1)

CB (IEC60950-1)

Quick Start Guide

– 7 –

Safety and Regulatory Information

IEEE 802.11b/g/n Enterprise Access Point

WAP3110-L

This document provides information on switch safety, regulatory statements and

compliances. It includes these sections:

◆“Compliances and Safety Statements” on page 7

◆“Warnings and Cautionary Messages” on page 12

Compliances and Safety Statements

FCC Class B This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. This transmitter must not be co-

located or operating in conjunction with any other antenna or transmitter.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the following measures:

◆Reorient or relocate the receiving antenna

◆Increase the separation between the equipment and receiver

◆Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected

◆Consult the dealer or an experienced radio/TV technician for help

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this

equipment.

Quick Start Guide

– 8 –

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 20 cm between the radiator and your body.

NCC (Taiwan) 低功率電波輻射性電機管理辦法：

第十二條 : 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用

者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條 : 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現

有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通

信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工

業、科學及醫療用電波輻射性電機設備之干擾。

CE Mark CE Mark Declaration of Conformance for EMI and Safety (EEC)

This is a class B product. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures.

National Restrictions

This device is intended for home and office use in all EU countries (and other

countries following the EU directive 1999/5/EC) without any limitation except for

the countries mentioned below:

Country Restriction Reason/Remark

Bulgaria None General authorization required for outdoor use and

public service

France Outdoor use limited

to 10 mW e.i.r.p.

within the band

2454-2483.5 MHz

Military Radiolocation use. Refarming of the 2.4 GHz band

has been ongoing in recent years to allow current relaxed

regulation. Full implementation planned 2012

italy None If used outside of own premises, general authorization is

required

Luxembourg None General authorization required for network and service

supply(not for spectrum)

Norway Implemented This subsection does not apply for the geographical area

within a radius of 20 km from the centre of Ny-Ålesund

Russian

Federation None Only for indoor applications

Quick Start Guide

– 9 –

Note:

Do not use the product outdoors in France.

Europe - EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive 1999/

5/EC. The following test methods have been applied in order to prove presumption

of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:

◆EN 60950-1:2006 + A11: 2009

Safety of Information Technology Equipment.

◆EN 300 328 V1.7.1: 2006-10

Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband

transmission systems; Data transmission equipment operating in the 2,4 GHz

ISM band and using wide band modulation techniques; Harmonized EN

covering essential requirements under article 3.2 of the R&TTE Directive.

◆EN 301 489-17 V1.8.1/ 2008-04

EN 301 489-17 V2.1.1/ 2009-05

Electromagnetic compatibility and Radio spectrum Matters (ERM);

Electromagnetic Compatibility (EMC) standard for radio equipment and

services; Part 17: Specific conditions for 2.4 GHz wideband transmission

systems.

◆EN 55022: 2006 + A1: 2007

Limits and methods of measurement of radio disturbance characteristics of

information technology equipment.

◆EN 55024: 1998 + A1: 2001 + A2: 2003

Information technology equipment immunity characteristics limits and

methods of measurement.

◆EN 62311: 2008

Assessment of electronic and electrical equipment related to human exposure

restrictions for electromagnetic fields (0 Hz - 300 GHz).

This device is a 2.4 GHz wideband transmission system (transceiver), intended for

use in all EU member states and EFTA countries, except in France and Italy where

restrictive use applies.

In Italy the end-user should apply for a license at the national spectrum authorities

in order to obtain authorization to use the device for setting up outdoor radio links

and/or for supplying public access to telecommunications and/or network services.

This device may not be used for setting up outdoor radio links in France and in

some areas the RF output power may be limited to 10 mW EIRP in the frequency

range of 2454 - 2483.5 MHz. For detailed information the end-user should contact

the national spectrum authority in France.

Quick Start Guide

– 10 –

This equipment may be operated in:

Bulgarian

Български

Снастоящето, SMC декларира, че това безжично устройство евсъответствие със

съществените изисквания идругите приложими разпоредби на Директива 1999/5/

EC.

Czech

Česky

SMC tímto prohlašuje, že tento Radio LAN device je ve shoděse základními požadavky

a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Danish

Dansk

Undertegnede SMC erklærer herved, at følgende udstyr Radio LAN device overholder de

væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF

Dutch

Nederlands

Hierbij verklaart SMC dat het toestel Radio LAN device in overeenstemming is met de

essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG

Bij deze SMC dat deze Radio LAN device voldoet aan de essentiële eisen en aan de

overige relevante bepalingen van Richtlijn 1999/5/EC.

English Hereby, SMC, declares that this Radio LAN device is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC.

Estonian

Eesti

Käesolevaga kinnitab SMC seadme Radio LAN device vastavust direktiivi 1999/5/EÜ

põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Finnish

Suomi

Valmistaja SMC vakuuttaa täten että Radio LAN device tyyppinen laite on direktiivin 1999/

5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

French

Français

Par la présente SMC déclare que l'appareil Radio LAN device est conforme aux

exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE

German

Deutsch

Hiermit erklärt SMC, dass sich dieser/diese/dieses Radio LAN device in

Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten

Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi)

Hiermit erklärt SMC die Übereinstimmung des Gerätes Radio LAN device mit den

grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie

1999/5/EG. (Wien)

Greek

Ελληνική

με την παρουσα SMC δηλωνει οτι radio LAN device συμμορφωνεται προσ τισ ουσιωδεισ

απαιτησεισ και τισ λοιπεσ σχετικεσ διαταξεισ τησ οδηγιασ 1999/5/εκ.

Hungarian

Magyar

Alulírott, SMC nyilatkozom, hogy a Radio LAN device megfelel a vonatkozó alapvetõ

követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Italian

Italiano

Con la presente SMC dichiara che questo Radio LAN device è conforme ai requisiti

essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Latvian

Latviski

Ar šo SMC deklarē, ka Radio LAN device atbilst Direktīvas 1999/5/EK būtiskajām

prasībām un citiem ar to saistītajiem noteikumiem.

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de SMC Networks

SMC Networks

SMC Networks EliteConnect SMC2555W-AG2 Manual de usuario

SMC Networks

SMC Networks 2682W FICHE Manual de usuario

SMC Networks

SMC Networks WAP5110 Manual de usuario

SMC Networks

SMC Networks SMCWEBS-N Manual de usuario

SMC Networks

SMC Networks 2655W FICHE Manual de usuario

SMC Networks

SMC Networks E21011 Manual de usuario

SMC Networks

SMC Networks EliteConnect WAP5110 Manual de usuario

SMC Networks

SMC Networks EliteConnect SMCE21011 Manual de usuario

SMC Networks

SMC Networks EZ Connect Turbo SMC2455W Manual de usuario

SMC Networks

SMC Networks WEBS-N Manual de usuario

SMC Networks

SMC Networks SMCWAPS-G Manual de usuario

SMC Networks

SMC Networks EliteConnect SMC2555W-AG Manual de usuario

SMC Networks

SMC Networks EZ Connect SMC2652W Manual de usuario

SMC Networks

SMC Networks SMC2552W-G2 Manual de usuario

SMC Networks

SMC Networks EZ Connect Manual de usuario

SMC Networks

SMC Networks SMC EZ Connect g SMCWTK-G Manual de usuario

SMC Networks

SMC Networks 2552W-G2 Manual de usuario

SMC Networks

SMC Networks EZ Connect SMCWEB-N Manual de usuario

SMC Networks

SMC Networks SMCDPCR-AP Manual de usuario

SMC Networks

SMC Networks EZ Connect SMC2655W Manual de usuario

SMC Networks

SMC Networks EZ CONNECT SMC2755W Manual de usuario

SMC Networks

SMC Networks EliteConnect SMC2891W-AG Manual de usuario

SMC Networks

SMC Networks EZ Connect Turbo SMC2455W Manual de usuario

SMC Networks

SMC Networks EliteConnect SMC2555W-AG2 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario