SMC Networks EliteConnect SMCWHSG44-G Manual de usuario

SMCWHSG44-G

Information furnished by SMC Networks, Inc. (SMC) is believed to be accu-

rate and reliable. How-ever, no responsibility is assumed by SMC for its use,

nor for any infringements of patents or other rights of third parties which

may result from its use. No license is granted by implication or otherwise

under any patent or patent rights of SMC. SMC reserves the right to change

specifications at any time without notice.

SMC Networks, Inc.

38 Tesla

Irvine, California 92618

Trademarks

SMC is a registered trademark; and EliteConnect is a trademark of SMC

Networks. Other product and company names are trademarks or registered

trademarks of their respective holders.

LIMITED WARRANTY

Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products

to be free from defects in workmanship and materials, under normal use and

service, for the applicable warranty term. All SMC products carry a standard

90-day limited warranty from the date of purchase from SMC or its Authorized

Reseller. SMC may, at its own discretion, repair or replace any product not

operating as warranted with a similar or functionally equivalent product, during

the applicable warranty term. SMC will endeavor to repair or replace any product

returned under warranty within 30 days of receipt of the product. The standard

limited warranty can be upgraded to a Limited Lifetime* warranty by registering

new products within 30 days of purchase from SMC or its Authorized Reseller.

Registration can be accomplished via the enclosed product registration card

or online via the SMC Web site. Failure to register will not affect the standard

limited warranty. The Limited Lifetime warranty covers a product during the

Life of that Product, which is defined as the period of time during which the

product is an “Active” SMC product. A product is considered to be “Active”

while it is listed on the current SMC price list. As new technologies emerge,

older technologies become obsolete and SMC will, at its discretion, replace an

older product in its product line with one that incorporates these newer

technologies. At that point, the obsolete product is discontinued and is no

longer an “Active” SMC product. A list of discontinued products with their

respective dates of discontinuance can be found at:

http://www.smc.com/index.cfm?action=customer_service_warranty.

All products that are replaced become the property of SMC. Replacement

products may be either new or reconditioned. Any replaced or repaired product

carries either a 30-day limited warranty or the remainder of the initial warranty,

whichever is longer. SMC is not responsible for any custom software or

firmware, configuration information, or memory data of Customer contained

in, stored on, or integrated with any products returned to SMC pursuant to any

warranty. Products returned to SMC should have any customer-installed

accessory or add-on components, such as expansion modules, removed prior

to returning the product for replacement. SMC is not responsible for these

items if they are returned with the product. Customers must contact SMC for

a Return Material Authorization number prior to returning any product to

SMC. Proof of purchase may be required. Any product returned to SMC without a

valid Return Material Authorization (RMA) number clearly marked on the outside

of the package will be returned to customer at customer's expense. For warranty

claims within North America, please call our toll-free customer support number

at (800) 762-4968.

Customers are responsible for all shipping charges from their facility to SMC.

SMC is responsible for return shipping charges from SMC to customer.

WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS

WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY SHALL BE REPAIR OR

REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC'S OPTION. THE

FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN

LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,

EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE,

INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR

AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY

IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF

ITS PRODUCTS. SMC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS

TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE

PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY

THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING,

UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND

THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR

OTHER HAZARD. LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED

IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE

FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAM-

AGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR

OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE

SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR

INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED

RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES

OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR

CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS

MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL

RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS

WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.

* SMC will provide warranty service for one year following discontinuance

from the active SMC price list. Under the limited lifetime warranty, internal

and external power supplies, fans, and cables are covered by a standard

one-year warranty from date of purchase.

SMC Networks, Inc.

38 Tesla

Irvine, CA 92618

Warranty in EMEA and Asia Pacific:

For details regarding warranty in EMEA and Asia Pacific, please contact your

country sales representative. All contact information can be found at

www.smc.com

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiated radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example - use only shielded

interface cables when connecting to computer or peripheral devices). Any

changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 20 cm between the radiator & your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Industry Canada - Class B

This digital apparatus does not exceed the Class B limits for radio noise

emissions from digital apparatus as set out in the interference-causing

equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.

Cet appareil numerique respecte les limites de bruits radioelectriques

applicables aux appareils umeriques de Classe B prescrites dans la norme

sur le material brouilleur: “Appareils Numeriques,” NMB-003 edictee par

l'Industrie.

EC Conformance Declaration

SMC contact for these products in Europe is:

SMC Networks Spain S.L.,

Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2o, 4a,

08970 - Sant Joan Despí,

Barcelona, Spain.

Signed and dated Copy of the Declaration of Conformity can be found in the

product section of www.smc-europe.com

This RF product complies with R&TTE Directive 99/5/EC. For the evaluation

of the compliance with this Directive, the following standards were applied:

• Electromagnetic compatibility and radio spectrum matters (ERM)

EN300 328-1 (2001-12)

EN300 328-2 (2001-12)

• Electromagnetic Compatibility (EMC) Standard for radio equipment and services

EN301 489-1 V1.4.1 : 2002

EN301 489-17 V1.2.1 : 2002

•SafetyTest

EN60950-1 : 2001

The conformity assesment procedure referred to in Article 10 and detailed in

Annex IV of the Directive 1999/5/EC has been followed related to Articles

3.2 with the involvement of the following Notified Body:

BTS-ETZ Certification GmBH, Storkkower Strasser 38c, D-15562,

Reichenwalde B, Berlin, Germany

Identification Mark

Countries of Operation & Conditions of Use in the European Community

This device is intended to be operated in all countries of the European

Community. Requirements for indoor vs. outdoor operation, license requirements

and allowed channels of operation apply in some countries as described below:

Note: The user must use the configuration utility provided with this product

to ensure the channels of operation are in conformance with the spectrum

usage rules for European Community countries as described below.

• This device requires that the user or installer properly enter the current

country of operation in the command line interface as described in the

user guide, before operating this device.

• This device will automatically limit the allowable channels determined by

the current country of operation. Incorrectly entering the country of

operation may result in illegal operation and may cause harmful interference

to other system. The user is obligated to ensure the device is operating

according to the channel limitations, indoor/outdoor restrictions and

license requirements for each European Community country as described

in this document.

• This device may be operated indoors or outdoors in all countries of the

European Community using the 2.4 GHz band: Channels 1 - 13, except

where noted below.

• In Italy the end-user must apply for a license from the national spectrum

authority to operate this device outdoors.

• In Belgium outdoor operation is only permitted using the 2.46 - 2.4835 GHz

band: Channel 13.

• In France outdoor operation is only permitted using the 2.4 - 2.454 GHz

band: Channels 1 - 7

Notified Countries for intended use:

Austria, Belgium, Denmark, Finland, France, Germany, Italy, Luxembourg,

Netherlands, Norway, Spain, Sweden Switzerland, United Kingdom, Portugal,

Greece, Ireland, Iceland

Safety Compliance

Power Cord Safety

Please read the following safety information carefully before installing the switch:

WARNING: Installation and removal of the unit must be carried out by

qualified personnel only.

• The unit must be connected to an earthed (grounded) outlet to comply

with international safety standards.

• Do not connect the unit to an A.C. outlet (power supply) without an earth

(ground) connection.

• The appliance coupler (the connector to the unit and not the wall plug) must

have a configuration for mating with an EN 60320/IEC 320 appliance inlet.

• The socket outlet must be near to the unit and easily accessible. You can

only remove power from the unit by disconnecting the power cord from

the outlet.

• This unit operates under SELV (Safety Extra Low Voltage) conditions

according to IEC 60950. The conditions are only maintained if the

equipment to which it is connected also operates under SELV conditions.

France and Peru only

This unit cannot be powered from IT supplies. If your supplies are of IT type,

this unit must be powered by 230 V (2P+T) via an isolation transformer ratio

1:1, with the secondary connection point labelled Neutral, connected directly

to earth (ground).

† Impédance à la terre

Important! Before making connections, make sure you have the correct cord

set. Check it (read the label on the cable) against the following:

Power Cord Set

U.S.A. and Canada The cord set must be UL-approved and CSA certified.

The minimum specifications for the flexible cord

are: - No. 18 AWG - not longer than 2 meters, or 16

AWG. - Type SV or SJ - 3-conductor

The cord set must have a rated current capacity

of at least 10 A

The attachment plug must be an earth-grounding

type with NEMA 5-15P (15 A, 125 V) or NEMA 6-

15P (15 A, 250 V) configuration.

Denmark The supply plug must comply with Section 107-2-

D1, Standard DK2-1a or DK2-5a.

Switzerland The supply plug must comply with SEV/ASE 1011.

U.K. The supply plug must comply with BS1363 (3-pin

13 A) and be fitted with a 5 A fuse which complies

with BS1362.

The mains cord must be <HAR> or <BASEC>

marked and be of type HO3VVF3GO.75 (minimum).

Europe The supply plug must comply with CEE7/7

(“SCHUKO”).

The mains cord must be <HAR> or <BASEC>

marked and be of type HO3VVF3GO.75 (minimum).

IEC-320 receptacle.

Veuillez lire à fond l'information de la sécurité suivante avant

d'installer le Switch:

AVERTISSEMENT: L'installation et la dépose de ce groupe doivent être

confiés à un personnel qualifié.

• Ne branchez pas votre appareil sur une prise secteur (alimentation électrique)

lorsqu'il n'y a pas de connexion de mise à la terre (mise à la masse).

• Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la

masse) afin de respecter les normes internationales de sécurité.

• Le coupleur d'appareil (le connecteur du groupe et non pas la prise murale)

doit respecter une configuration qui permet un branchement sur une

entrée d'appareil EN 60320/IEC 320.

• La prise secteur doit se trouver à proximité de l'appareil et son accès doit

être facile. Vous ne pouvez mettre l'appareil hors circuit qu'en débranchant

son cordon électrique au niveau de cette prise.

• L'appareil fonctionne à une tension extrêmement basse de sécurité qui est

conforme à la norme IEC 60950. Ces conditions ne sont maintenues que si

l'équipement auquel il est raccordé fonctionne dans les mêmes conditions.

France et Pérou uniquement:

Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre.

Si vos alimentations sont du type impédance à la terre, ce groupe doit être

alimenté par une tension de 230 V (2 P+T) par le biais d'un transformateur

d'isolement à rapport 1:1, avec un point secondaire de connexion portant l'ap-

pellation Neutre et avec raccordement direct à la terre (masse).

Cordon électrique- Il doit être agréé dans le pays d'utilisation

Etats-Unis et Canada: Le cordon doit avoir reçu l'homologation des

UL et un certificat de la CSA.

Les spe'cifications minimales pour un cable flexible

sont AWG No. 18, ouAWG No. 16 pour un cable de

longueur infe'rieure a` 2 me'tres. - type SV ou

SJ - 3 conducteurs

Le cordon doit être en mesure d'acheminer un

courant nominal d'au moins 10 A.

La prise femelle de branchement doit être du

type à mise à la terre (mise à la masse) et

respecter la configuration NEMA 5-15P (15 A, 125 V)

ou NEMA 6-15P (15 A, 250 V).

Danemark: La prise mâle d'alimentation doit respecter la

section 107-2 D1 de la norme DK2 1a ou DK2 5a.

Cordon électrique- Il doit être agréé dans le pays d'utilisation

Suisse: La prise mâle d'alimentation doit respecter la

norme SEV/ASE 1011.

Europe La prise secteur doit être conforme aux normes

CEE 7/7 (“SCHUKO”)

LE cordon secteur doit porter la mention <HAR>

ou <BASEC> et doit être de type HO3VVF3GO.75

(minimum).

Otros manuales para EliteConnect SMCWHSG44-G

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Puerta de SMC Networks

SMC Networks

SMC Networks SMCD3G Manual de usuario

SMC Networks

SMC Networks ClimateWorx FieldServer ProtoNode FPC-N34 Manual de usuario

SMC Networks

SMC Networks SMCD3GN3 Manual de usuario

SMC Networks

SMC Networks LEC-GDN1 Series Manual de usuario

SMC Networks

SMC Networks EZ Connect SMC8014-TES Manual de usuario

SMC Networks

SMC Networks LEC-GPR1 Series Manual de usuario

SMC Networks

SMC Networks EX500-GPR1A Manual de usuario

SMC Networks

SMC Networks EZ Networking SMC8013WG Manual de usuario

SMC Networks

SMC Networks EX500-GEN2 Series Manual de usuario

SMC Networks

SMC Networks EZ Connect 2.4GHz 54Mbps Wireless Cable Modem Gateway... Manual de usuario

SMC Networks

SMC Networks ProtoAir FPA-W44 Guía del usuario

SMC Networks

SMC Networks SMC8004CM Manual de usuario

SMC Networks

SMC Networks EliteConnect SMCWHSG14-G Manual de usuario

SMC Networks

SMC Networks ProtoAir FPA-W34 Guía del usuario

SMC Networks

SMC Networks SMCD3GN Manual de usuario

SMC Networks

SMC Networks SMCD3GN2 Manual de usuario

SMC Networks

SMC Networks LEC-GEN1 Manual de usuario

SMC Networks

SMC Networks EX500-GPR1A-X20 Series Manual de usuario

SMC Networks

SMC Networks EtherNet/IP EX500-GEN1 Manual de usuario

SMC Networks

SMC Networks EliteConnect SMCWHSG14-G Manual de usuario

SMC Networks

SMC Networks EX500-GPR1A-X8 Series Manual de usuario

SMC Networks

SMC Networks SMC8511 Manual de usuario

SMC Networks

SMC Networks FieldServer FS-QS-2XX0 Guía del usuario

SMC Networks

SMC Networks DOCSIS 3.0 Commercial Cable Modem Gateway... Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario