SKYLUX Climax 36178 Manual de usuario
CANOPY
Climax®
Installation instructions
Self-supporting aluminium profile system
EN
Art.N° 36178
E_MH_Installation_instructions_Skylux_Climax 20/11/2020
2/88
Safety
Take the necessary and required safety precautions, such as safety nets and lifelines when installing from the
outside, safety goggles, gloves, hard hat, etc.
Do not step on the glass.
Falling from height
• When using ladders to go on the roof:
- Ladder in good condition?
- Set up correctly at an angle of 75°?
- Secured below and on top against moving?
- Don’t take heavy material with you on the ladder (3-point contact rule)! If possible,
use a crane to lift the material.
• If you are going on the roof, make sure there is a walking surface that is wide enough and that
supports on the beams of the lower structure.
•When using an aerial work platform: always wear and secure your harness (mandatory)! Leaving
the cage is forbidden.
• Never walk backwards on a roof, always walk forwards.
• Make sure there’s enough light in the working zone.
Low-hanging obstacles and falling loads
• Forbidden to walk under or within a radius of 1 m of a hanging or lifted load.
• Demarcate the danger zone below the zone where there is a risk of material falling down
during the installation of the veranda.
• It’s prohibited to enter these danger zones during construction.
Crushing hazard
• All working tools are in good condition, provided with a valid CE label and all necessary safety
regulations. These cannot be removed.
• People who use these working tools are educated for this purpose. Protections are always
present on all working tools. They are in good condition and need to be set correctly.
Tripping/falling
•Safety is key and it begins with order and tidiness. Clean everything immediately, leave nothing
lying around.
• Trash needs to be sorted.
• Be cautious with electric cables (danger of tripping/falling). Never walk backwards!
• Make sure there’s enough light in the working zone.
20/11/2020 3/88
E_MH_Installation_instructions_Skylux_Climax
Sharp objects
• Make sure your fingers/hands are not pinched and watch out for cuts while handling veranda
parts.
• Be careful where you put your hands during the installation.
• Wearing cut-resistant gloves is mandatory.
Ergonomics
• Always lift loads correctly: bend your knees, move your feet instead of forcing your spine, lift
as close to your body as possible.
• Parts of more than 25 kg must be lifted with at least 2 persons.
Personal protective equipment
• Work clothes, safety shoes and helmet are mandatory for everyone.
• Lifeline and harness are mandatory if the edge is not secured enough or if there are no safety nets below the
veranda roof. They are also necessary when using an aerial working platform.
• Use gloves when handling veranda parts.
• Safety glasses and hearing protection are mandatory when using saws / grinders.
Always perform a Last Minute Risc Analysis!
If in doubt: STOP! Do not take unnecessary risks. Ask your supervisor if needed.
E_MH_Installation_instructions_Skylux_Climax 20/11/2020
4/88
SAFETY p. 2 3
CONTENTS p. 4 5
OVERVIEW OF CLIMAX PROFILES AND PARTS p. 6 10
GENERAL INSTALLATION TIPS p. 11 20
MEASURING YOUR CLIMAX PITCHED ROOF p. 12 13
MEASURING YOUR CLIMAX SADDLE ROOF p. 14 15
PREPARATION p. 16
GENERAL TIPS AND MAINTENANCE
INSTRUCTIONS p. 17 - 18
PLAN OF CONSERVATORY ROOF WITHOUT
THERMAL BRIDGE p. 19
PLAN OF CONSERVATORY ROOF WITH
THERMAL BRIDGE p. 20
SPECIFIC INSTALLATION TIPS FOR THE CLIMAX
SYSTEM WITHOUT THERMAL BRIDGE p. 21 41
POSTS p. 22 23
GUTTER p. 24 27
HINGE PROFILE p. 28
WALL PROFILE p. 29
SUPPORTS AND SIDE SUPPORTS p. 30 33
GLAZING p. 34 35
FINISH p. 36 41
SPECIFIC INSTALLATION TIPS FOR THE CLIMAX
SYSTEM WITH THERMAL BRIDGE p. 42 67
POSTS p. 43 44
GUTTER p. 45 48
HINGE PROFILE p. 49
WALL PROFILE p. 50
SUPPORTS AND SIDE SUPPORTS p. 51 55
GLAZING p. 56 57
FINISH p. 58 67
Table of contents
20/11/2020 5/88
E_MH_Installation_instructions_Skylux_Climax
SPECIFIC INSTALLATION TIPS FOR THE CLIMAX
SADDLE ROOF SYSTEM p. 68 74
PREPARATION OF THE RIDGE PROFILES OF
A SADDLE ROOF p. 69 70
INSTALLATION OF THE RIDGE PROFILES OF
A SADDLE ROOF p. 71
PREPARATION OF THE TIE BAR FOR THE
SADDLE ROOF p. 72
INSTALLATION OF THE TIE BAR FOR THE
SADDLE ROOF p. 73
SIDE FINISH OF THE SADDLE ROOF p. 74
ANNEX p. 75 84
LOAD GRAPHS p. 76 80
LOAD GRAPHS FOR ROOFS WITH
PLASTIC SHEETS p. 77 78
LOAD GRAPHS FOR ROOFS WITH
GLASS p. 79 80
SPECIFIC INSTALLATION TIPS FOR POSTS
WITH GD2 p. 81
SPECIFIC INSTALLATION TIPS FOR
CONNECTING GLAZING p. 82 83
GLAZING THICKNESS TABLE p. 84
Table of contents
E_MH_Installation_instructions_Skylux_Climax 20/11/2020
6/88
Overview of Climax profiles and parts
MT WALL TOP
MB WALL BOTTOM
S1 HINGE
S2 HINGE
G GUTTER
GI
GI 0
GI 90
GI 120
GI 150
GI -90
INSIDE GUTTER FOR G
CONNECTION FOR G
OUTSIDE CORNER PIECE 90°
OUTSIDE CORNER PIECE 120°
OUTSIDE CORNER PIECE 150°
INSIDE CORNER PIECE 90°
GD 1 GUTTER SUPPORT
GD 2 GUTTER SUPPORT
GD2C COVER FOR GUTTER SUPPORT GD2
GDP THERMAL BREAK GD2
SB HINGE BOTTOM
WALL
GUTTER
G120A GUTTER 120 A
GR RAISED PROFILE FOR GUTTER
D1 SUPPORT
D2 SUPPORT
D3 SUPPORT
TP THERMAL SUPPORT
TPG THERMAL SUPPORT FOR GLASS
ZD SIDE SUPPORT
ZD2B SIDE SUPPORT D2 CLIPS
ZDC SIDE SUPPORT COVER 16, 25, 32 MM
L432 L-FINISH SIDE SUPPORT
L END PROFILE FOR GLASS
SUPPORTS
20/11/2020 7/88
E_MH_Installation_instructions_Skylux_Climax
Overview of Climax profiles and parts
L632 L END PROFILE FOR GLASS
V642 STEEL TUBE 60X40X2 GALVA
L16P ALUMINIUM SIDE PROFILE 16, 25,
32 MM
CL16 ALUMINIUM CLIP 16 MM
CL32 ALUMINIUM CLIP 25/32 MM
CLL SIDE CLIP 16, 25, 32 MM
CLSB BASE SCREW-IN CLIP
CLST TOP SCREW-IN CLIP FOR 8 TO 34 MM
CLSL TOP SCREW-IN SIDE CLIP
P POST PART 110/50
PC POST CLIP FOR P
POSTS
PCB POST CLIP BASE FOR P
98 POST 50/100
97A POST CLIP BASE FOR POST CLIP
WITHOUT COAT
97B POST CLIP
100 POST 100/100
C1CX
COEX SEAL FOR WALL TOP WHITE/
BLACK
COEX SEAL FOR WALL TOP GREY/
BLACK
C12 SUPPORT CORD FOR C1CX
C2CX COEX SEAL WHITE/BLACK FOR TP-TPG
COEX SEAL GREY/BLACK FOR TP-TPG
C5 SEAL (GREY) FOR SHEET SPACER OR
SIDE SUPPORT
C8 SEAL (GREY) FOR CL16, CL32 AND
CLSB
CY10 SEAL (GREY) FOR CL16, CL32 AND
CLSB FOR GLASS
SEALS
E_MH_Installation_instructions_Skylux_Climax 20/11/2020
8/88
Overview of Climax profiles and parts
C11CX COEX SEAL FOR GUTTER/RIDGE
WHITE/BLACK
C31 SUPPORT SEAL FOR GLASS
A1 SPACER A1
A2 SPACER A2
GVT TOP PROFILE FOR GLASS
CONNECTOR
GVB BOTTOM PROFILE FOR GLASS
CONNECTOR
Y10 ADAPTOR PROFILE 8 MM FOR 10 MM
SHEET
Y25 ADAPTOR PROFILE 9 MM FOR 25 MM
SHEET
Y32 ADAPTOR PROFILE 15 MM FOR 32 MM
SHEET
Y16A RAISED PROFILE ALUMINIUM 16 MM
Y16P THERMAL BREAK ABS 16 MM
ACCESSORIES
U16P REINFORCED PVC END PROFILE 16
MM WHITE
U25P REINFORCED PVC END PROFILE 25
MM WHITE
U32P REINFORCED PVC END PROFILE 32
MM WHITE
U16A ALUMINIUM END PROFILE 16 MM
U32A ALUMINIUM END PROFILE 32 MM
U16 PRE-DRILLED ALUMINIUM END
PROFILE 16 MM
U32 PRE-DRILLED ALUMINIUM END
PROFILE 32 MM
BT16 CLOSED PLASTIC TAPE 10 AND 16 MM
WITH GUARANTEE
BT25 CLOSED PLASTIC TAPE 25 MM WITH
GUARANTEE
BT32 CLOSED PLASTIC TAPE 32 MM WITH
GUARANTEE
BB16 PERFORATED PLASTIC TAPE 16 MM
WITH GUARANTEE
20/11/2020 9/88
E_MH_Installation_instructions_Skylux_Climax
Overview of Climax profiles and parts
BB25 PERFORATED PLASTIC TAPE 25 MM
WITH GUARANTEE
BB32 PERFORATED PLASTIC TAPE 32 MM
WITH GUARANTEE
K STRAIGHT CONNECTOR
S163 STOP 16/3
S323 STOP 32/3
S383 STOP 38/3 FOR GLASS
ZDCS END PIECE FOR SIDE SUPPORT
COVER
GAS1 GUTTER SLIDE END FOR G+GD
GAS2 GUTTER SLIDE END FOR GD
GAS3 GUTTER SLIDE END FOR GD2 + G
G120AS GUTTER SLIDE END FOR G12OA
GAP1 THERMAL END PANEL FOR GD1
GAP2 THERMAL END PANEL FOR GD2
GRS1 GUTTER SLIDE END FOR GR ON G120A
GRS2 GUTTER SLIDE END FOR G+GD+GR
GRS3 GUTTER SLIDE END FOR GD2 + G + GR
GDCA SLIDE END FOR GD2C
LOGO OVERFLOW COVER FOR GUTTER
SLIDE END
MAS WALL SLIDE END FOR MT+MB
NASZ RIDGE SLIDE END SADDLE ROOF
909 CONNECTING PIN
GDC SUPPORT BRACKET FOR GUTTER
SUPPORT
CLIMAX
E_MH_Installation_instructions_Skylux_Climax 20/11/2020
10/88
Overview of Climax profiles and parts
NCZ SUPPORT BRACKET FOR SADDLE
ROOF RIDGE
PV BASE PLATE FOR POST
PU U-TOP, BOTTOM FOR POST P AND
BASE PLATE PV
BMR STAINLESS STEEL BOLT, NUT AND
SPRING RING M8
UT10 U-TOP, BOTTOM FOR POST 100 AND
BASE PLATE PV
UT98 U-TOP, BOTTOM FOR POST 98 AND
BASE PLATE PV
GC OUTLET + SWIVEL Ø 80 mm
BUGS
WUGS
UNIVERSAL GUTTER SPOUT +
OUTLET GUTTER SPOUT
8423 CENTRAL DRAWING RING
8420 CENTRAL ROSETTE COVER
8425 RIDGE FIXATION
8424 END-PIECE FOR THREADED BAR
8426 EYE BOLT M10 x 50
8421 TUBE PULLER SET
ZSB
ZSG
ZSC
SELF-DRILLING STAINLESS STEEL SCREW
(NON-COATED)
SELF-DRILLING STAINLESS STEEL SCREW
(COATED)
SELF-DRILLING STAINLESS STEEL SCREW
WITH SEALING
6,3 x 25 SELF-DRILLING SCREW 6,3 x 25 mm
PS48 PARKER STAINLESS STEEL SCREW 4.8
x 25 mm
PST PARKER SCREW 4.8 x 13 mm
TX25
10
PH2
TX25
Tabla de contenidos
Otros manuales de Carpa de SKYLUX
SKYLUX
SKYLUX Climalux 36179 Manual de usuario
SKYLUX
SKYLUX Climalux Manual de usuario
SKYLUX
SKYLUX Climalux Manual de usuario
SKYLUX
SKYLUX Cintralux alu 25 mm Manual de usuario
SKYLUX
SKYLUX Climaglide Manual de usuario
SKYLUX
SKYLUX Climacrown Manual de usuario
SKYLUX
SKYLUX Climax Panorama Manual de usuario
SKYLUX
SKYLUX ClimaCar Manual de usuario
