Simu TSA 4 Manual de instalación

Hz Key Chain Transmitters 2 and 4 channels

Read all instructions carefully before use.

Hz Key Chain Trans

1) Program the motor using a

standard transmitter as per the

quick reference guide

2) Press the programming button

on the standard transmitter until

the motor jogs up/down

3) Touch the programming

contact on the back of the Key

Chain Transmitter with a metal

conductor (paper clip). The LED

on the front will start to flash

Programming

Contact

Paper

Clip Flashing LED

4) Press the desired front button

while the LED is still flashing. The

motor will jog. This button will now

control the motor.

Repeat steps 1 through 4 for other buttons to other motors if desired.

Note: Only program one motor per button. The 2 channel key chain can be used

to control 2 motors maximum and the 4 channel can control 4 motors maximum

Programming Instructions

PGR

PROGRAMMING

Hz Key Chain Transmitters 2 and 4 channels

Read all instructions carefully before use.

Hz Key Chain Trans

Programming Instructions

REPLACING THE BATTERY

LOCKING/UNLOCKING TSA 4

A - Enabling the locking function - Once a locking code has been entered the TSA 4 will automatically lock the buttons after 2

minutes without a command to prevent unintended operation. The buttons can be unlocked as per section B.

1) Press the lock button

for 5 seconds

2) Enter a 4 key code 3) Validate the code by

pressing the lock button

4) Enter the same 4

key code again

5) Validate the code by

pressing the lock button

ATTENTION - The battery must be installed correctly with regards to the polarity. The battery must be installed with the + side facing away from the

transmitter board. Do not expose battery to high temperatures or water. Do not throw batteries in fire or water. Dispose of batteries correctly

B - Unlocking the remote - After unlocking the remote, the buttons will remain active for 2 minutes before locking again.

1) Enter your 4 key

code

2) Validate the code by

pressing the lock button

3) The transmitter buttons are unlocked for normal use for 2 minutes.

After 2 minutes the transmitter will automatically lock the buttons again

C - Disable the automatic lock function

1) Press the lock button

for 5 seconds

2) After 5 seconds the locking

LED will go out. The locking

Function is now disabled.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de Simu

Simu

Simu 2006020 Manual de usuario

Simu

Simu COLOR Hz Manual de usuario

Simu

Simu 5C Manual de usuario

Simu

Simu Hz TIMER Manual de usuario

Simu

Simu TIMER EASY Manual de usuario

Simu

Simu HZ WALL 1 CHANNEL Manual de usuario

Simu

Simu LiveIn2 Manual de usuario

Simu

Simu Hz COLOR MULTI Manual de usuario

Simu

Simu 2008806 Manual de usuario

Simu

Simu HZ MOBILE 1 CANAL Manual de usuario

Simu

Simu TIMER EASY Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario