Simex SRD-N16 Manual de usuario

Assisting the automation
industry since 1986   
User manual
DATA RECORDER
SRD- 16
•Firmware: v.3.40 b1 or higher
•Loggy Soft: v.1.10.0 or higher
•S-Toolkit: v.2.1.0 or higher
Read the user's manual carefully before starting to use the unit or software. 
Producer reserves the right to implement changes without prior notice.
 2019.0 .16 SRD-N16_INSSXEN_v.1.08.001 

User manual - DATA RECORDER SRD-N16 and cooperating software
CONTENTS

BASIC REQUIREMENTS AND USER SAFETY........................................................................................4
GENERAL CHARACTERISTICS................................................................................................................5
TECHNICAL DATA......................................................................................................................................7
DEVICE INSTALLATION..........................................................................................................................12
1. UNPACKING....................................................................................................................................12
2. ASSEMBLY......................................................................................................................................12
3. CONNECTION METHOD.................................................................................................................16
3.1.Connection  of current type input  ( I ver ion ).......................................................................18
3.2.Connection  of voltage type input  ( U ver ion ).....................................................................19
3.3.Connection  of temperature type input   ( RTD ver ion ).......................................................20
3.4.Connection  of thermocouple type input   ( TC ver ion ).......................................................21
4. MAINTENANCE................................................................................................................................21
FRONT PANEL DESCRIPTION................................................................................................................23
PRINCIPLE OF OPERATION...................................................................................................................24
1. MEASUREMENT MODE..................................................................................................................24
1.1.Mea urement range  definition of current input  ( U/I ver ion ).............................................24
1.2.Mea urement range  definition of RTD and TC input  ( TC/RTD ver ion )............................25
1.3.Recording momentary and averaged data...............................................................................26
2. MODES OF RESULT PRESENTATION..........................................................................................27
2.1. "Single channel" mode............................................................................................................28
2.2."Mea urement  li t" mode.......................................................................................................29
2.3.”Graph” mode...........................................................................................................................32
2.4.”Channel  Li t” mode...............................................................................................................35
3. PRINCIPLE OF OUTPUTS OPERATION........................................................................................37
3.1.Alarm ......................................................................................................................................37
3.2.Output  control.........................................................................................................................38
3.3.Example of output control........................................................................................................40
DEVICE PROGRAMMING.........................................................................................................................41
1. PARAMETERS EDITION.................................................................................................................43
1.1.Numeric and  witching parameter  ("LIST" - type)..................................................................43
1.2. Text parameter ......................................................................................................................44
1.3.“SLIDER” - type parameter .....................................................................................................45
2. DESCRIPTION OF RESULTS PRESENTATION MODES MENU.................................................46
2.1."Mea urement  li t option " menu...........................................................................................46
2.2.”Graph option ” menu..............................................................................................................47
2.3.”Channel  li t option ” menu....................................................................................................47
3. RESULTS PRESENTATION MODES MENU STRUCTURE..........................................................48
4. MAIN MENU DESCRIPTION...........................................................................................................49
4.1.”Device information” menu.......................................................................................................49
4.2.”Di play option ” menu............................................................................................................49
4.3.”Logging  etup” menu..............................................................................................................50
4.4.“Temperature unit” parameter (RTD ver ion)..........................................................................52
4.5.”Input  etting ” menu (common parameter )...........................................................................53
4.6.”Input  etting ” menu ( I ver ion )............................................................................................54
4.7.”Input  etting ” menu ( U ver ion )...........................................................................................55
4.8.”Input  etting ” menu ( RTD ver ion )......................................................................................57
4.9.”Input  etting ” menu ( TC ver ion )........................................................................................58
4.10.”Output   etting ” menu.........................................................................................................59
4.11.”Date & time  etting ” menu..................................................................................................61
4.12.”RS485 port  etting ” menu...................................................................................................61
4.13.”Acce   etup” menu.............................................................................................................62
4.14.”USB option ” menu...............................................................................................................63
 

User manual - DATA RECORDER SRD-N16 and cooperating software
4.15.”Language” menu...................................................................................................................64
4.16.”Default  etting ” menu..........................................................................................................64
5. MAIN MENU STRUCTURE..............................................................................................................65
DO NLOADING DATA FROM DATA LOGGER.....................................................................................67
1. MODBUS (RS485) DATA DOWNLOAD..........................................................................................67
2. USB FLASH DRIVE (PENDRIVE) DATA DOWNLOAD..................................................................67
THE MODBUS PROTOCOL HANDLING.................................................................................................70
1. LIST OF REGISTERS......................................................................................................................70
2. TRANSMISSION ERRORS HANDLING..........................................................................................76
3. EXAMPLES OF QUERY/ANSWER FRAMES.................................................................................77
USER'S SETTINGS LIST........................................................................................................................80

GENERAL CHARACTERISTICS..............................................................................................................87
INSTALLATION AND STARTUP..............................................................................................................87
USING THE PROGRAM............................................................................................................................90
1. „CURRENT MEASUREMENT” MENU.............................................................................................91
2. „REPORTS” MENU..........................................................................................................................91
2.1.„Table” tab................................................................................................................................92
2.2.„Graph” tab...............................................................................................................................94
3. „CONFIGURATION” MENU.............................................................................................................99
3.1.„Device ” tab..........................................................................................................................100
3.2.„Group ” tab - group operation .............................................................................................104
3.3.„Setting ” tab..........................................................................................................................106
4. LIST OF ERRORS AND FAULT DIAGNOSTICS .........................................................................108

GENERAL CHARACTERISTICS............................................................................................................109
INSTALLATION AND STARTUP............................................................................................................109
USING PROGRAM..................................................................................................................................110
1. “INPUTS SETTINGS” TAB.............................................................................................................111
2. “OUTPUTS SETTINGS” TAB.........................................................................................................112
3. “LOGGING SETUP” TAB...............................................................................................................112
4.  “INTERFACE OPTIONS” TAB......................................................................................................113
5. “DEVICE INFORMATION” TAB.....................................................................................................115
6. CONFIGURATION MODES...........................................................................................................116
6.1.Individual configuration of channel .......................................................................................116
6.2.Configuring  elected channel ...............................................................................................116
6.3.Configuring all channel .........................................................................................................116
7. UPDATING DEVICE FIRMWARE..................................................................................................117
3

User manual - DATA RECORDER SRD-N16 and cooperating software

Explanation of symbols used in the manual:

- Thi ymbol denote e pecially important guideline concerning the in tallation and

operation of the device. Not complying with the guideline denoted by thi ymbol

may cau e an accident, damage or equipment de truction.

IF THE DEVICE IS NOT USED ACCORDING TO THE MANUAL THE USER IS

RESPONSIBLE FOR POSSIBLE DAMAGES.

- Thi ymbol denote e pecially important characteri tic of the unit.

Read any information regarding thi ymbol carefully

I. USER MANUAL FOR DATA RECORDER

1. BASIC REQUIREMENTS AND USER SAFETY

-    !"# $%"&&  '(  !)%  &(*)!('+,  #)&  !-  .  /(  $ "(.  +-

'! **&)*&' %  '!(% ,, %')!0  !)%   '!% '!'!/  %  *&)*&  !1'&)!!% ,

$)!.'%')!( !."('!/%"!'%$)!%& &-%)'%( (('/!!%

- Installation should be conducted by qualified personnel . During installation all

available safety requirements should be considered. The fitter is responsible for

executing the installation according to this manual, local safety and EMC

regulations.

- The unit must be properly set-up, according to the application. Incorrect

configuration can cause defective operation, which can lead to unit damage or

an accident.

- If the device is equipped with PE conntector, it should be connected to PE wire.

- #'!%$ ()# "!'% ,#"!$%')!%&'( &'(2)# (&')"(%& %%)%

( #%-  )#  *)*,  )&  *&)*&%-  ..'%')! ,0  '!.*!.!%  (-(%(  !.

(),"%')!(%)*&1!%("$ %& %"(%+"(.

- "!'%"((. !/&)"(1),% /% %$ !$ "( ,% , $$'.!%"!'%

"(%+ (3'%$.)## !..'($)!!$%.#&)%*)3& ("**,-*&')&%)

(% &%'!/'!(% ,, %')!)#%&)"+,())%'!/4'!%$ ()# ,#"!$%')!5

- Neighbouring and connected equipment must meet the appropriate standards

and regulations concerning safety and be equipped with adequate overvoltage

and interference filters.

-)!)% %%*%%).'( ((+,0&* '&)&).'#-%"!'%-)"&(,#"!'%

 (!)"(&(&1'$ +,* &%( #$%'1"!'%("(%+.'($)!!$%. !.

("+'%%.#)&&* '&( % ! "%)&'6.(&1'$$!%&

User manual - DATA RECORDER SRD-N16 and cooperating software

- Do not use the device in areas which are vulnerable to excessive quakes,

vibrations, corrosive gases and oils.

- Do not use the device in potentially explosive environments.

- Do not use the device in water vapor condensation and icing exposed places.

- Do not use the device in places which are exposed to direct sunlight.

- It is necessary to insure that temperature around the device does not exceed

recommended values. If so, take under consideration forced cooling of

the device (e.g. using fan).

"!'%'(.('/!. #)&)*& %')! '! !'!."(%&' ,!1'&)!!% !."(%

!)%+"(.'! )"(),.!1'&)!!%)&('', &

2. GENERAL CHARACTERISTICS

• Multifunctional

Deviceis designed for recording, displaying current or averaged values and

presentation of technological parameter trends in graphic form.

• Large data storage capacity

The registered measurement results are recorded in the unit's memory. The

capacity of installed memory allows to store over 2 000 000 measurements.

• Configurable measurement and control input

The unit has up to 8 measurement channels (depending on version) of

measurement signals and one digital voltage input with programmable functions,

e.g. control of the recording process. Each signal can be freely configured and

described. Depending on device version all measured parameters must be available

as current type signals (0-20 mA or -20 mA standards for I version), voltage type

signals (0-5 V, 1-5 V, 0-10 V or 2-10 V standards for U version or standards K, S, J,

T, N, R, B, E for TC version) or resistance (Pt100, Pt500 or Pt1000 standards for

RTD version). The internal analogue-digital converter has a 12 or 16 bit resolution

(depending on input type), which provides high measurement resolution results.

Additionally, individual alphanumeric description (text) of each of the recorded

channels is possible.

• Fast serial interface

The data logger is fitted with a galvanic isolation RS- 85 interface, programmed

with ModBus RTU transmission protocol. This enables the connection of a number

of data recorders into the network, remote collecting of data from each unit and also

remote configuration. The application of the RS- 85 interface instead of RS-232 is

due to the possibility of achieving high transmission speeds using transmission lines

of larger length than is possible with the RS-232 interface.

User manual - DATA RECORDER SRD-N16 and cooperating software

• Built-in USB Host interface

The device is equipped with built-in USB Host interface, allowing for data transfer to

popular USB Flash Drives (PenDrives). This method allows for significant

simplification of unit application: it is no longer necessary to connect PC and data

logger via RS- 85 interface.

Significant acceleration of data transfer is an additional advantage: data download

can be 10 times faster than using RS- 85 interface.

78 Device should work properly with any standard Flash Drives, but

manufacturer can not guarantee proper cooperation with non-standard devices, or

with devices developed after data logger release.

• ide range of power supply voltage and external sensor power supply

The built-in pulse power supply allows to power the device with 85...9:...260 V

AC/DC, 16...9...35 V AC, 19...9...50 V DC, 11...9...16 V DC, 10...9...13 V AC

(depending on version). Data recorder (version with current inputs only) is equipped

with output for powering the sensor and converters with 2 V DC ±5% and

max.current 50 mA for 11...9...16 V DC, 10...9...13 V AC power supply voltage

and max. 200 mA for other power supply voltage.

• Legible graphic display

The 128 x 6 points display with a backlight mounted on front of the unit is a big

advantage of the data recorder. It allows the display of trend graphs for each

channel separately. Different operation modes provide the possibility of selecting

and adjusting the method of data presentation depending on the user's

requirements. Data recording intervals are selected by the user from the menu

level. Additionally, it is possible to set the display to show one current value

measured for a selected channel.

• Easy configuration

There are 6 keys on the front of the data recorder that enable the configuration of

the unit. The menu assisted with full text descriptions makes the unit configuration

process quite easy. However, due to a significant number of configured parameters

it is advised to use the attached configuration software for PCs.

User manual - DATA RECORDER SRD-N16 and cooperating software

3. TECHNICAL DATA

Power supply voltage

(depending on version)

External Fuse (required)

Power consumption

85...9:...260 V AC/DC; 50 ÷ 60 Hz (separated),

19...9...50 V DC, 16 V...9...35 V AC (separated)

or 11...9...16 V DC, 10...9...13 V AC (separated)

T - type, max. 2 A

for power supply voltage: 12 V DC max. 5 W,

for other power supply voltage:

typically 3 VA; max. 5 VA

Measurement inputs

(depending on version)

I version:

U version:

RTD version:

TC version:

up to 8 inputs 0-20 mA or -20 mA, common ground,

overload protection, input current is limited to 50mA

(typical)

up to 8 inputs 0-5V, 1-5V, 0-10V, 2-10V, common ground

up to 8 inputs Pt100, Pt500 or Pt1000 type with

automatic connection recognition (2 or 3-wires)

up to 8 thermocouple inputs type K, S, J, T, N, R, B, E

Digital input 1 input 2 V DC, galvanic isolation

power consumption: 7,5 mA / 2 V,

isolation: 1min @ 500V AC.

Outputs 2 electromagnetic relays, NO type,

5A/250V AC (resistance)

3A/250V AC (reactance)

Recording cycle 1 sec./ 2 sec. / 5 sec. / 10 sec. / 15 sec. / 20 sec. /

30 sec. /1 min. / 2 min. / 5 min. / 10 min. / 15 min. /

20 min. / 30 min. / 60 min.

Communication interface

Baud rate

RS- 85, 8N1 / Modbus RTU, galvanic isolated:

1min @ 500V DC.

1200 bit/s ÷ 115200 bit/s

USB Host interface Cooperation with standard Flash Disks

Display

Backlight color

(depending on version)

LCD graphic display, 128 x 6 points, with backlight

white or amber

Data memory 8 MB

Protection level IP 65

User manual - DATA RECORDER SRD-N16 and cooperating software

Housing type

Housing material

Housing dimensions (L x H x D)

without glands

with glands

(depending on version)

version with 1 to inputs

version with 8 inputs

panel

ABS + polycarbonate

166 x 161 x 103 mm

166 x 189 x 103 mm

166 x 192 x 103 mm

Glands

power supply and relays

RS- 85 and digital input

measurement inputs

(depending on version)

version with 1 to 2 inputs

version with inputs

version with 8 inputs

1 x M20 with insert for cables 2 x 5mm

1 x M16 without insert

1 x M20 with insert for cables 2 x 5mm

2 x M20 with insert for cables 2 x 5mm

2 x M25 with insert for cables x 5mm

(inserts provide tight seal by filling spaces between the

wires)

Operating temperature

Storage temperature

Humidity

Altitude

0°C to +50°C (standard)

-20°C to +50°C (optional)

-10°C to +70°C (standard)

-20°C to +70°C (optional)

5 to 90% no condensation

up to 2000 meters above sea level

Screws tightening max. torque 0,5 Nm

Max. connection leads diameter 3 mm2

Safety requirements according to: PN-EN 61010-1

installation category: II

pollution degree: 2

voltage in relation to ground: 300V AC

insulation resistance: >20MW

isolation strength between power supply and input/output

terminal: 1min. @ 2300V (see '/:)

EMC PN-EN 61326-1

Device described in this manual is available in two versions differed by

measurement inputs type. This manual contain following short descriptions:

I version - means device with current type inputs (0..20mA, ..20mA)

U version - means device with voltage type inputs (0..5V, 1..5V, 0..10V,

2..10V)

RTD version - means device with RTD-type inputs (Pt100, Pt500, Pt1000)

TC version - means device with TC-type inputs (K, S, J, T, N, R, B, E)

Parameters of current type inputs ( I version )

Input type 0-20 mA or -20 mA, common ground

Measurement range ± 9999 plus decimal point

User manual - DATA RECORDER SRD-N16 and cooperating software

Current measurement accuracy ± 0.1% @ 25°C; ± one digit (for 0-20 mA range)

Temperature stability 50 ppm / °C

Sampling rate 8 sps

Accepted prolonged input overload 20%

Measurement input resistance 120 W

Sensor power supply output 2 V DC ± 5% and max. current:

50 mA for power supply voltage 11...9...16 V DC,

10...9...13 V AC,

200 mA for other power supply voltage,

Uninsulated from measurement inputs

Parameters of voltage type inputs ( U version )

Input type 0-5V, 1-5V, 0-10V, 2-10V, common ground

Measurement range ± 9999 plus decimal point

Current measurement accuracy ± 0.1% @ 25°C; ± one digit (for 0-10 V range)

Temperature stability 50 ppm / °C

Sampling rate 8 sps

Accepted prolonged input overload 20%

Measurement input resistance 6 kW

Parameters of RTD type inputs ( RTD version )

Input type Pt100, Pt500 or Pt1000 type with automatic

connection recognition (2 or 3-wires)

Measurement range -100,0°C ÷ +600,0°C

-1 8,0°F ÷ +999,9°F

Measurement accuracy ± 0.15% @ 25°C; ± one digit

Temperature stability 100 ppm / °C

Sampling rate 1 sample per 2.5 sec

Measurement wires resistance max. 20 W (every wire)

Parameters of TC type inputs ( TC version )

Input type Thermocouple type K, S, J, T, N, R, B, E

Measurement range K:

Voltage:

-200°C

-50°C

-210°C

-200°C

-50°C

250°C

-200°C

-30mV

-50mV

1370°C

1768°C

1200°C

00°C

1300°C

1768°C

1820°C

1000°C

80mV

120mV

Measurement accuracy ± 0.1% @ 25°C; ± one digit

Accuracy of cold ends temperature

compensation ± 1°C

User manual - DATA RECORDER SRD-N16 and cooperating software

Temperature stability 50 ppm / °C

Sampling rate 2 sps

Accepted prolonged input overload 20,00%

Input impedance typ. 1MW

Measurement inputs should be connected with isolated signals (it is

recommended to use shielded cables)

Cables connected to RTD inputs can not be longer than 30 meters and must be

laid completely in building.

Software (Window environment)

•S-Toolkit, PC software for data logger easy configuring,

•Loggy Soft, PC software for moving, reporting, archiving and displaying recorded data.

'(;"'*!%'(!)%'!%!..#)&"('!&('.!%' ,!1'&)!!%( !. -

!)%*&)1'. .;" %*&)%$%')!%)& .')&$*%')!'!("$!1'&)!!%(

Carefully check that the isolation used with the unit ('/  :) meets the

expectations and if necessary use appropriate measures of overvoltage protection.

Additionally, insure the appropriate air and surface insulation gaps when installing

( + :).

Range of operating voltage Air gap [mm] Surface gap [mm]

Up to 50V RMS or DC 0,2 1,2

Up to 100V RMS or DC 0,2 1,

Up to 150V RMS or DC 0,5 1,6

Up to 300V RMS or DC 1,5 3,0

Tab. 3.1. Minimal in ulation gap according to EN 61010-1

Tabla de contenidos

Otros manuales de Registrador de datos de Simex

Simex

Simex PMS-90R Manual de usuario

Simex

Simex SRD-99 Manual de usuario

Simex

Simex SRD-99X Manual de usuario

Simex

Simex SRD-99 Manual de usuario

Manuales populares de Registrador de datos de otras marcas

TESTO

TESTO 176 Manual de usuario

HT Italia

HT Italia XL421 Manual de usuario

HBM

HBM SOMAT XR CX22B-R Manual de usuario

Agtrix

Agtrix 380i Manual de usuario

Hobo

Hobo H8 Pro Manual de usuario

Beijing ART Tech

Beijing ART Tech PCI2320 Manual de usuario

Athena

Athena GET SL1 Manual de usuario

Motec Systems

Motec Systems C185 Manual de usuario

Beijing ART Tech

Beijing ART Tech USB2832 Manual de usuario

Rotronic

Rotronic HygroLog HL20 Manual de usuario

MRC

MRC DW-6092 Manual de usuario

Racelogic

Racelogic VBOX LapTimer Manual de usuario

Edu-Logger

Edu-Logger 900-240 Manual de usuario

Elma

Elma DT173 Manual de usuario

MadgeTech

MadgeTech PRTemp140 Hoja de especificaciones

Comet

Comet U0121M Manual de usuario

pico Technology

pico Technology PT-104 Manual de usuario

Soil Instruments

Soil Instruments GTecLink Manual de usuario