SilverStone RAVEN Z Manual de usuario
Signature RAVEN styled
front panel adorned
with addressable RGB light strip
RE
RED
EFI
EFINE
S
S
FF
FF
COM
COMPU
TI
TIN
G WITH
G WITH FL
AI
AIR
RE
RED
EFI
EFINE
S
S
FF
FF
COM
COMPU
TI
TIN
G WITH
G WITH FL
AI
AIR
RVZ03-ARGB
SilverStone RVZ03 is a further evolution of the highly rated
RAVEN Z RVZ01-E, a slim form factor case with tremendous
capability. It has the same optimized interior that has room for a
standard ATX (PS2) power supply and support for some the
biggest consumer graphics cards on the market with superb air
cooling performance. Designed for use in either vertical or
horizontal orientation, it can be placed comfortably in any
space-constrained environment that requires a powerful PC. For
those looking to build a slim form factor PC with extra flair, the
RVZ03’s inclusion of addressable RGB lighting and controller
bring about another exciting chapter to the famed RAVEN series
of computer cases.
Signature RAVEN styled front panel adorned with addressable
RGB light strip
Mini-ITX motherboard & ATX PSU compatible for wide array of
building possibilities
Support cards up to 13 inches (330mm) to fit most high-end
GPUs for compute power far exceeding consoles
Maximum performance in slim form factor with support for AIO
liquid cooling
Positive air pressure design for excellent cooling/quietness
and dust-prevention
Fits in nearly any environment with horizontal or vertical
orientation
SPECIAL FEATURES
INTRODUCTION
SPECIFICATIONS
SST-RVZ03B-ARGB (black), SST-RVZ03W-ARGB (white)
Reinforced plastic outer shell, steel body
Mini-DTX, Mini-ITX
Internal
Top
Bottom
2
USB3.0 x 2, Audio x 1, MIC x 1
Optional PS2 (ATX)
Compatible up to 13" (330mm) long, width restriction-5.88" (149mm)
83mm
150mm*
4.05kg
382mm (W) X 105mm (H) X 364mm (D) , 14.6 liters
2.5" x 3
1 x 120mm fan, 1500rpm, 18dBA
1 x 120mm fan, 1500rpm, 18dBA
1 x 120mm fan slot
Model
Material
Motherboard
Drive Bay
Cooling System
Expansion Slot
Front I/O Port
Power Supply
Expansion Card
Limitation of CPU cooler
Limitation of PSU
Net Weight
Dimension
Support Kensington lock, PCI Express riser card set x 1
ARGB control PCB x 1
Extra
* Maximum length for power supply is 150mm but we recommend
140mm deep power supply due to varying connector locations
and the unique structure of RVZ03.
Due to the use of internal power cord extension, we recommend
not to exceed 800W when powering off a 110V outlet
(no limit for 220V).
DISASSEMBLE CHART
2.5" HDD X1 2.5" HDD X2
12015 FAN X1
12015 FAN X1
MINI-ITX (OPTION)
USB 3.0 + SPK + MIC
POWER BUTTON
POWER LED
HDD LED
RESET BUTTON
FAN FILTER X1
ITEM PURPOSE
RUBBER-A-FEET PAD
RUBBER-E-FEET PAD
TOP-CARD-BKT
BOTTOM-CARD-BKT
LOGO-HORIZONTAL-PAD
VGA-COMP-BELOW-RUBBER
SCREW C 632 X8
SCREW D M2 X2
SCREW E 632 X5
SCREW F M3 X4
BAG
PCI-EXTEND-CARD
SCREW A O4 X15-M3 X4 SECURE RADIATOR COOLING FAN
SECURE 2.5" SSD/HDD
SECURE MOTHERBOARD, PSU
SECURE OPTICAL DRIVE
SECURE VGA SUPPORT BRACKET
FOR VERTICAL USE
FOR HORIZONTAL USE
SECURE RADIATOR COOLING FAN
SCREW B O4 X15-632 X4
CONTROLLER CABLE
ARGB SIGNAL CONTROLLER
CONTROL PANEL CABLE
ADOPTER CABLE
TOP COVER
POWER CAGE
ATX PSU (OPTION)
ARGB CAGE
FAN FILTER X2
INSTALLATION GUIDE
Unscrew the screws from the rear of the chassis then
remove the top cover
Have all components collected.
Check that all components do not have compatibility problems
with each other or with the case.
If possible, assemble the components outside the case first to
make sure they are working.
Keep the motherboard manual ready for reference during
installation.
Prepare a Philips screwdriver.
Be careful not to strike on glass side panel when removing it
from the case.
Before you begin, please make sure that you
1
3
2
Unscrew the screws from PSU bracket then remove it
Unscrew the screws from the graphics card support
bracket then remove it
5
4
If you want to use SilverStone NT06-PRO or other similar
CPU cooler, please relocate the top panel 120mm fan to
the bottom vent near the graphics card area
Insert the I/O shield included with your motherboard then
install the motherboard into the chassis
1 2
7
6
We recommend at this point connecting all the necessary
cables including the SATA cables to the motherboard
Secure the PSU into the PSU bracket
9
8
Place the PSU bracket on top of the chassis then connect
the power cord to the PSU
Insert the PSU bracket into its original position and secure
with screws
10
Remove expansion slot cover and install graphics card into
the graphics card support bracket
11
Depending on the design of your graphics cards, install
and adjust the graphics card holder to a proper position to
support your card. Adhere included rubber padding
according to the height of graphics card’s backside, one
(for 3mm thick backplate) or two (for no backside components)
Included Foam Pad
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Recinto de SilverStone
SilverStone
SilverStone PT13 Manual de usuario
SilverStone
SilverStone Raven RVZ02 Manual de usuario
SilverStone
SilverStone PS04B Manual de usuario
SilverStone
SilverStone sugo series sg09 Manual de usuario
SilverStone
SilverStone Temjin SST-TJ11B-W Manual de usuario
SilverStone
SilverStone Lascala LC14 Manual de usuario
SilverStone
SilverStone sg12 Manual de usuario
SilverStone
SilverStone PS07 Manual de usuario
SilverStone
SilverStone DS222 Manual de usuario
SilverStone
SilverStone TS231U-C Manual de usuario
SilverStone
SilverStone PT13-120 Manual de usuario
SilverStone
SilverStone SG04-F Manual de usuario
SilverStone
SilverStone CS380 Manual de usuario
SilverStone
SilverStone Lascala LC16M Manual de usuario
SilverStone
SilverStone PM01 Manual de usuario
SilverStone
SilverStone raven RVX01 Manual de usuario
SilverStone
SilverStone Lascala LC03 Manual de usuario
SilverStone
SilverStone Precision PSO1-E Manual de usuario
SilverStone
SilverStone MS09 Manual de usuario
SilverStone
SilverStone SG11 Manual de usuario
