SilverStone Mammoth MM01 Manual de usuario

Mammoth Series MM01

Professional chassis with integrated HEPA filter

for harsh or critical environments

Installation and system optimization guide:

Specification P.2

Introduction P.1

Disassemble chart P.3

Installation guide P.5

Connector definition P.17

Front I/O connector guide P.19

Component size limitations P.20

CPU and graphic card supporter P.29

Optimal Thermal Performance Layout P.32

Upgrade And Maintenance P.39

Warranty Information

P.47Q & A

P.55

The following manual and guides were carefully prepared by the SilverStone engineering team

to help you maximize the potential of your SilverStone product. Please keep this manual for

future reference when upgrading or performing maintenance on your system. A copy of this

manual can also be downloaded from our website at:http://www.silverstonetek.com

The following manual and guides were carefully prepared by the SilverStone engineering team to

help you maximize the potential of your SilverStone product. Please keep this manual for future

reference when upgrading or performing maintenance on your system.Acopy of this manual can also

be downloaded from our website at:

http://www.silverstonetek.com

Installation and system optimization guide:

Product Overview

Specifications

Disassemble Chart

Installation Guide

Connector Definition

Front I/O connector Guide

Component Size Iimitations

CPU And Graphic Card Supporter

Optimal Thermal Performance Layout

Upgrade And Maintenance

Q&A

Warranty Information

P.1

P.2

P.3

P.5

P.17

P.19

P.20

P.29

P.33

P.39

P.47

P.55

Product Overview

Introduction

For computer designers, creating a chassis capable of surviving harsh environments is a tough task, especially if dust

isamajorproblem. Mostresorttofanlessconfigurationasthiseliminatesthepossibilityofdustbuildupintroducedbyactive

airflow into the chassis, which is the main cause of system overheating over time. But limited heat dissipation capacity

afforded by fanless designs confines systems to lower powered CPUs and Mini-ITX boards with less features.

To overcome this limitation, SilverStone’s R&D team once again challenged and overturned convention by coming up

with an answer in the Mammoth MM01 chassis. Instead of completely sealing off airflow to prevent dust, the MM01 has a

partially-sealed design with active filtering. To prevent dust from entering the chassis, a HEPAfilter is used to cover the air

intake area, making MM01 the first retail computer chassis to incorporate this internationally recognized filtering technology.

Used frequently by clean room in factories, operating room in hospitals, or facilities requiring dust-free environment, the

HEPA filter has the ability to remove airborne particles far exceeding what’s available in traditional computer equipments.

In order for this to work without suffocating airflow, two Air Penetrator fans were selected for use in the MM01. With a

combined rating of up to 340CFM, they provide air pulling power similar to typical household fans and make it possible to

maintain proper cooling for high-end components despite the presence of highly restrictive HEPA filters.

Complementing the tremendous ability to keep dust at bay, the MM01 also has unique, downward slanting front and

rear vents to keep liquid from flowing in from the top of the chassis. This simple, yet affective design helps MM01 take on

much harsher conditions required by professionals working in places not normally suitable for computers. For those

choosingtouseMM01innormalhomeoroffice,itssuperiorfilteringcouldpotentiallyhelpcleanuptheworkingenvironment

as well!

Mammoth Series MM01

Product Overview

Aluminum door, plastic anti-splash grille, steel panels and body

SSI-EEB, SSI-CEB, Extended ATX, ATX, Micro-ATX

Front

SST-MM01B (black)

USB 3.0 x 2 audio x 1 MIC x 1

1 x Optional standard PS2 (ATX) no length limitation

Compatible up to 13.3” long, width restriction-6.69”

183mm

271mm (W) x 542mm (H) x 597mm (D), 87.69 liters

Includes HEPA filter

*AP182’s original top speed is 2000rpm, but high resistance introduced by HEPA filter reduces top speed

by 200rpm.

3.5" x 7 ( hot-swap x1 ) , 2.5” x 4

2 x AP182 180mm intake fan 500~1800rpm*, 17~42 dBA

5.25" x 2

Internal

1 x 120mm fan slotRear

Exposed

Specifications

Material

Model

Motherboard

Drive Bay

Cooling System

Expansion Slot

Front I/O Port

Power Supply

Expansion Card

Limitation of CPU cooler

Dimension

Extra

Mammoth Series MM01

Disassemble Chart

Secure 2.5” HDD

Secure optical drives

Secure VGAholder and claw

Secure PSU, 12025 fan, motherboard and 3.5” HDD

Motherboard standoff

VGAsupporter holder

VGAsupporter claw

Standoff socket wrench

Cable management

SCREW - P - M3 4 - BK

SCREW - THUMB - M3 6 - BK

SCREW - THUMB - 6 - 32 6 - BK

SCREW - I - 6 - 32 5 - BK

STANDOFF - 6 - 32 6.5H - 6 - 32

VGA- SUPPORT - HOLDER

VGA- SUPPORT - CLAW

STANDOFF - SOCKET - WRENCH

BUNCH - WIRE - TIES

PICTURE ITEM PURPOSE

PSU (OPTION)

TOP COVER

REAR PANEL

RIGHT PANEL

FRONT PANEL

5.25” DRIVE BAY x 2

MOTHERBOARD TRAY

180 FAN x 2 OR

120 FAN x 3 (OPTION) 3.5” DRIVE BAY x 1

3.5” DRIVE BAY x 1

2.5” DRIVE BAY x 4

120 FAN x 1 (OPTION)

3.5” DRIVE BAY x 5

HEPAFilter

LEFT PANEL

USB3.0 x 2 + SPK + MIC

RESET BUTTON

POWER BUTTON

Mammoth Series MM01

Disassemble Chart

Mammoth Series MM01

Installation guide

Before you begin, please make sure that you

have all components collected

check that all components do not have compatibility problems with each other or with the case

if possible, assemble the components outside the case first to make sure they are working

keep the motherboard manual ready for reference during installation

Lösen Sie die beiden Schrauben

an den linken und rechten

Seitenwänden, nehmen Sie die

Seitenwände ab.

Desserrez les vis des deux

panneaux latéraux pour les

retirer.

Desatornille dos tornillos de los

paneles izquierdo y derecho para

quitarlos.

Per rimuovere i pannelli laterali

allentare, per entrambi, le due

viti di serraggio.

Loosen two screws from both

left and right side panels to

remove them.

Отвинтите по два винта,

крепящих левую иправую

боковых панели, иснимите

панели.

왼쪽과 오른쪽 사이드 패널에서

두 개씩 나사를 풀어 사이드

패널을 제거합니다.

取下左右側板各兩顆螺絲，

卸下側板。

取下左右侧板各两颗螺丝，

卸下侧板。

両方の左右パネルからネジ

2本を緩めて、取り外します。

Entfernen Sie die obere Blende,

indem Sie sie nach hinten

drücken.

Retirez le panneau supérieur en

le poussant vers l'arrière.

Retire el panel superior tirando

de él hacia la parte posterior.

Allentare le due viti sul lato

posteriore del telaio e poi

rimuovere il coperchio superiore.

Remove top panel by pushing

it toward the rear. Снимите верхнюю панель,

переместив ее назад.

뒤쪽으로 밀어 상단 패널을

분리하십시오.

將上蓋往後推，取下上蓋。

将上盖往后推，取下上盖。

上部パネルを後方に

押して取り外します。

Mammoth Series MM01

Lösen Sie die drei Schrauben,

welche die Motherboard-

Halterung fixieren, nehmen

Sie die Halterung ab.

Desserrez les trois vis tenant le

plateau de la carte mère pour le

démonter.

Desatornille tres tornillos que

sujetan la bandeja de la placa

base para quitarla.

Per rimuovere il supporto

scheda madre allentare le

tre viti di serraggio.

Loosen three screws holding

the motherboard tray to

remove it.

Отвинтите три винта,

крепящих кронштейн

материнской платы, и

снимите его.

3개의 나사를 풀어 메인보드

트레이를 제거합니다.

取下主機板托盤3顆螺絲，

將主機板托盤抽出。

取下主板托盘3颗螺丝，

将主板托盘抽出。

マザーボードトレイを固定

しているネジ3 本を緩めて、

取り外します。

將電源供應器由上放入機殼內，

如果有12公分或以上尺寸的

風扇建議朝下放置。

将电源供应器由上放入机壳内，

如果有12公分或以上尺寸的

风扇建议朝下放置。

Insert the power supply from

the top, if the power supply has

a build-in 120mm fan or larger,

we recommend installing the

power supply with its fan facing

down.

Установите блок питания в

верхней части корпуса. Если

блок питания оснащен

встроенным вентилятором

размером 120 мм или

больше, рекомендуется

устанавливать блок питания

вентилятором вниз.

電源は上面から入れます。電

源に120mm以上のファンが内

蔵されている場合、電源のフ

ァンが下向きになるよう設置

することを推奨します。

전원 공급장치에 120mm

이상의 내장 팬이 있는 경우,

상단에서 전원 공급장치를

삽입하십시오. 팬이 아래쪽을

향하도록 전원 공급장치를

설치하는 것이 좋습니다.

Setzen Sie das Netzteil von

oben ein; sofern das Netzteil

über einen120 mm-Lüfter (oder

größer) verfügt, empfehlen wir,

das Netzteil mit dem Lüfter

nach unten einzubauen.

Insérez la source

d'alimentation d'en haut, si la

source d'alimentation a un

ventilateur intégré de 120mm

ou plus, nous vous

recommandons d'installer la

source d'alimentation avec le

ventilateur face vers le bas.

Inserte la fuente de

alimentación desde arriba, si

la fuente de alimentación tiene

un ventilador de 120mm o

mayor incorporado, le

recomendamos instalar la

fuente de alimentación con el

ventilador hacia abajo.

Inserire l'alimentatore dall'alto,

se l'alimentatore ha una

ventola integrata da

120mm - o più grande; si

raccomanda di installare

l'alimentatore con la sua

ventola rivolta verso il basso

Installation guide

Mammoth Series MM01

Nehmen Sie die 3,5

Zoll-Laufwerkhalterung

heraus.

Retirez le casier des

lecteurs 3.5”.

Quite la carcasa para

dispositivos de 3,5”

Rimuovere il supporto hard

drive da 3,5”

Remove 3.5” drive cage. Извлеките кронштейн для

3,5-дюймовых жестких

дисков.

3.5” 드라이브 케이지를

제거합니다.

移除3.5吋主硬碟架。

移除3.5吋主硬盘架。

3.5インチドライブケージを取

り外します。

Lösen Sie die Schrauben,

welche den unteren

Festplattenkäfig fixieren,

nehmen Sie den Käfig ab.

Dévissez les vis pour l'enlever

en tenant la cage du lecteur

inférieur pour le retirer.

Afloje los tornillos sujetando

la carcasa para discos inferior

para retirarla.

Allentare le viti che fissano il

cage unità inferiore per

rimuoverlo.

Loosen the screws holding

the lower drive cages to

remove them.

Отверните винты крепления

нижнего отсека для жестких

дисков иизвлеките его.

하단 드라이브 케이지를

고정하는 나사를 풀어

케이지를 분리하십시오.

拆除底部硬碟架螺絲，

取下硬碟架。

拆除底部硬盘架螺丝，

取下硬盘架。

下部ドライブケージを保持

しているネジをゆるめて

取り外します。

Installation guide

Mammoth Series MM01

Tabla de contenidos

Otros manuales de Recinto de SilverStone

SilverStone

SilverStone DS322 Manual de usuario

SilverStone

SilverStone MMS01 Manual de usuario

SilverStone

SilverStone Precision Series Manual de usuario

SilverStone

SilverStone PI01 Manual de usuario

SilverStone

SilverStone FARA 512 Manual de usuario

SilverStone

SilverStone sugo series sg10 Manual de usuario

SilverStone

SilverStone MS09 Manual de usuario

SilverStone

SilverStone PT13-120 Manual de usuario

SilverStone

SilverStone Lucid Series Manual de usuario

SilverStone

SilverStone Lascala LC16M Manual de usuario

SilverStone

SilverStone DS321 Manual de usuario

SilverStone

SilverStone SST-PS06B Manual de usuario

SilverStone

SilverStone Fortress Series FT05 Manual de usuario

SilverStone

SilverStone SG04-F Manual de usuario

SilverStone

SilverStone FORTRESS SERIES FT03 Manual de usuario

SilverStone

SilverStone Lascala LC14 Manual de usuario

SilverStone

SilverStone CS280 Manual de usuario

SilverStone

SilverStone SG04-FH Manual de usuario

SilverStone

SilverStone Mammoth Series Manual de usuario

SilverStone

SilverStone RVZ01-E Manual de usuario

SilverStone

SilverStone DS222 Manual de usuario

SilverStone

SilverStone Precision PSO1-E Manual de usuario

SilverStone

SilverStone TS06 Manual de usuario

SilverStone

SilverStone ML09 Manual de usuario

Manuales populares de Recinto de otras marcas

SilentiumPC

SilentiumPC Armis AR5 Manual

Pulsar

Pulsar 17/TRP80/DSPR Manual de usuario

Thermaltake

Thermaltake V150 TG Manual de usuario

MSI

MSI MPG SEKIRA 500X Manual de usuario

Antec

Antec Dark fleet DF-10 Manual de usuario

Nexans

Nexans WTC05 Manual de usuario

Peavey

Peavey DS 1502 Manual de usuario

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manual de usuario

Rosewill

Rosewill RX82-U(JBOD) Manual de usuario

QNAP

QNAP SAS JBOD CLI 1.0 Manual de usuario

GAMDIAS

GAMDIAS Talos P1 Manual de usuario

Auvs

Auvs KR615 Manual de usuario

Digitus

Digitus DA-71114 Manual de usuario

CommScope

CommScope FDH 3000 Manual de usuario

FS FHD-FWME4 Manual de usuario

JBL

JBL CS1215T Manual de usuario

Pulsar

Pulsar ARAD-S4 Manual de usuario

Pulsar

Pulsar AWO454 Manual de usuario