Silicon Laboratories CP2104 Manual de usuario

CP2104-EK

CP2104 EVALUATION KIT USER’SGUIDE

1. Kit Contents

The CP2104 Evaluation Kit contains the following items:

CP2104 Evaluation Board

RS232 Serial Cable

USB Cable

DVD

Quick Start Guide

2. Relevant Documentation

Application notes can be found on the Interface Application Notes page for all fixed-function devices:

www.silabs.com/interface-appnotes.

AN721: CP210x/CP211x Device Customization Guide — Customize the VID, PID, serial number, and

other parameters stored in the CP2104 one-time programmable ROM.

AN197: Serial Communications Guide for CP210x — Programming guide for using the Virtual COM Port

(VCP) drivers.

AN169: USBXpress Programmer’s Guide — Programming guide for using the USBXpress drivers.

AN220: C8051F32x and CP210x USB Driver Customization — VCP or USBXpress driver customization

tool.

AN223: Port Configuration and GPIO for CP210x — Programming guide and DLL for runtime control of

the CP2104 GPIO pins.

AN571: CP210x Virtual COM Port Interface — USB interface details for CP210x devices.

3. Software Setup

The Software Development Kit (SDK) for the CP2104 kit is included on the kit DVD. The latest version of this

installer can also be downloaded from the www.silabs.com/interface-software website. This package includes:

Device Customization Utility (AN721)

Documentation —data sheet, application notes, user’s guide, quick start guide, etc.

CP210x Virtual COM Port (VCP) Drivers

Software — Driver Customization Utility (AN220) and programming examples

The Windows installer should launch automatically after inserting the DVD. For Mac and Linux, browse to the

appropriate directory on the DVD to install the software package. Follow the instructions to install the SDK and

drivers to the system.

3.1. USBXpress Driver Development Kit

The Silicon Laboratories USBXpress

Development Kit provides a complete host software solution for interfacing to

CP210x devices. No USB protocol or host device driver expertise is required. Instead, a simple, high-level Application

Program Interface (API) for the host software is used to provide complete USB connectivity. The USBXpress

Development Kit includes Windows device drivers, Windows device driver installer, host interface function library

(host API) provided in the form of a Windows Dynamic Link Library (DLL). See Application Note AN169, “USBXpress

Programmer’s Guide” for detailed information on using the USBXpress drivers.

The USBXpress drivers are available here: www.silabs.com/usbxpress.

Click the USBXpress Development Kit link in the Download for Windows 2000/XP/Server 2003/Vista/Win7 section

to download the USBXpress drivers. Run the installer and follow the steps to install the software to the desired

CP2104-EK

2 Rev. 0.7

location. The default installation directory is C:\SiLabs\MCU\USBXpress_SDK.

Further installation instructions for the WinCE drivers can be found in the ReadMe.txt file contained inside the

driver package.

4. CP2104 Hardware Interface

The evaluation board is connected to a PC as shown in Figure 1.

1. Connect one end of the USB cable to a USB Port on the PC.

2. Connect the other end of the USB cable to the USB connector on the

CP2104 evaluation board.

3. Connect one end of the RS232 serial cable to the DB-9 connector on the

CP2104 evaluation board

4. Connect the other end of the RS232 serial cable to the target serial device.

Figure 1. Hardware Setup

CP2104 EK

Serial Device

RS232

CP2104 USB-to-

UART Bridge

USB

CP2104-EK

Rev. 0.7 3

5. CP2104 Software Interface

If the Virtual COM Port drivers are used, the CP2104 will appear as a COM port in the Device Manager, as shown

in Figure 2. The CP2104 will always use the lowest available COM port for operation. For instance, if COM ports 1

and 2 are in use by other peripherals and applications, the CP2104 will use COM 3.

The CP2104 functions identically to a COM port from the reference point of both the host application and the serial

device, and it can support serial device control requests defined in the Microsoft Win32®Communications API.

Examples for how to communicate with the device as a serial COM port are included in AN197 on the

www.silabs.com/interface-appnotes page or in the SDK.

If the USBXpress drivers are used, the CP2104 will appear as a USB USBXpress device as shown in Figure 2.

Examples for how to communicate with the device using the USBXpress interface are included in AN169 on the

www.silabs.com/interface-appnotes page.

Figure 2. CP2104 in Device Manager

CP2104-EK

4 Rev. 0.7

6. Evaluation Board

The

CP2104

Evaluation Kit includes an evaluation board with a

CP2104

device pre-installed for evaluation and pre-

liminary software development. Numerous input/output (I/O) connections are provided to facilitate prototyping using

the evaluation board. Refer to

Figure 3

for the locations of the various I/O connectors.

P1 USB connector for USB interface

P2 DB9 connector for RS232 interface

J1 UART signal access connector

J2, J3 GPIO access connector

J4 Power connector

DS0–DS3 Green GPIO LEDs

DS4 Red SUSPEND indicator LED

Figure 3. CP2104 Evaluation Board with Default Shorting Blocks Installed

6.1. LED Headers (J2, J3)

Connectors J2 and J3 are provided to allow access to the GPIO pins on the CP2104. Place shorting blocks on J2

and J3 to connect the GPIO pins to the four green LEDs DS0–DS3. These LEDs can be used to indicate active

communications through the CP2104. Table 1 shows the LED corresponding to each header position.

6.2. Universal Serial Bus (USB) Interface (P1)

A Universal Serial Bus (USB) connector (P1) is provided to facilitate connections to the USB interface on the

CP2104. See Table 2 for the USB pin definitions.

Table 1. J2 and J3 LED Locations

LED Pins

DS0 J3[3:4]

DS1 J3[1:2]

DS2 J2[3:4]

DS3 J2[1:2]

Table 2. USB Connector Pin Descriptions

Pin # Description

1 VBUS

2D-

3D+

4 GND (Ground)

P2 CP2104

SUSPEND LED

Pin 2

Pin 1 J3

J2 DS3

DS2

DS1

DS0

_________

DS4

RS232

Transceiver

CP2104-EK

Rev. 0.7 5

6.3. UART Signals (P2, J1)

An RS232 transceiver circuit and DB9 connector (P2) are provided on the evaluation board to connect the CP2104

virtual serial port to external serial devices. See Table 3 for the RS232 P2 pin descriptions. The J1 connector is

provided to facilitate direct access to the CP2104’s UART signals. Shorting blocks on J1 are required to connect

the UART signals to P2. See Table 4 for J1 pin descriptions.

6.4. Power Connector (J4)

This header (J4) is included on the evaluation board to provide several power options. The following describes the

function of each pin:

Pins 1–2: Connects CP2104 VIO input (Pin 5) to CP2104 VDD (Pin 6). Remove the shorting block to power

VIO from an external source.

Pins 3–4: Connects the main +3 V net to the CP2104 VDD (Pin 6). The main +3 V net powers the other

components (four green LEDs and RS232 Sipex Part) on the evaluation board.

Table 3. RS232 Pin Descriptions

Pin Signal CP2104

Direction Description

1 DCD Input Data Carrier Detect

2 RXD Input Receive Data

3 TXD Output Transmit Data

4 DTR Output Data Terminal Ready

5 GND Ground

6 DSR Input Data Set Ready

7 RTS Output Request to Send

8 CTS Input Clear to Send

9 RI Input Ring Indicator

Table 4. J1 Pin Descriptions

Pins Signal CP2104

Direction Description

1–2 TXD Output Transmit Data

3–4 RXD Input Receive Data

5–6 DTR Output Data Terminal Ready

7–8 RI Input Ring Indicator

9–10 DCD Input Data Carrier Detect

11–12 DSR Input Data Set Ready

13–14 CTS Input Clear to Send

15–16 RTS Output Request to Send

CP2104-EK

6 Rev. 0.7

7. Schematic

Figure 4. CP2104 Evaluation Board Schematic

CP2104-EK

Rev. 0.7 7

DOCUMENT CHANGE LIST

Revision 0.1 to Revision 0.2

Updated "6.4. Power Connector (J4)" on page 5 to

reflect the updated schematic.

Updated J4 in Figure 4, “CP2104 Evaluation Board

Schematic,” on page 6.

Revision 0.2 to Revision 0.3

Updated "7. Schematic" on page 6.

Revision 0.3 to Revision 0.4

Updated "2.1.1. Virtual COM Port Driver Installation

for Windows" on page 1.

Updated "2.2.1. USBXpress Installation for

Windows" on page 2.

Removed “2.2.2. USBXpress Installation for

Windows 98SE” on page 2.

Revision 0.4 to Revision 0.5

Updated Figure 3 with shorting blocks installed.

Revision 0.5 to Revision 0.6

Updated "3. Software Setup" on page 1.

Revision 0.6 to Revision 0.7

Updated “1. Kit Contents” to change CD-ROM to

DVD.

Added “2. Relevant Documentation”.

Updated “3. Software Setup” to point to the drivers

on the website.

Updated Figure 1 and Figure 2.

http://www.silabs.com

Silicon Laboratories Inc.

400 West Cesar Chavez

Austin, TX 78701

USA

Simplicity Studio

One-click access to MCU and

wireless tools, documentation,

software, source code libraries &

more. Available for Windows,

Mac and Linux!

IoT Portfolio

www.silabs.com/IoT SW/HW

www.silabs.com/simplicity Quality

www.silabs.com/quality Support and Community

community.silabs.com

Disclaimer

Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or

intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical"

parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes

without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included

information. Silicon Labs shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted

hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of

Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal

injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no circumstances be used in weapons of mass

destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.

Trademark Information

Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®,

EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®,

Gecko®, ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® and others are trademarks or registered trademarks of Silicon

Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand

names mentioned herein are trademarks of their respective holders.

Tabla de contenidos

Otros manuales de Placa madre de Silicon Laboratories

Silicon Laboratories

Silicon Laboratories Si886xxISO-EVB Series Manual de usuario

Silicon Laboratories

Silicon Laboratories Si51211 Manual de usuario

Silicon Laboratories

Silicon Laboratories EFR32MG13 Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F411 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si1120 Manual de usuario

Silicon Laboratories

Silicon Laboratories EFM8UB2-SLSTK2001A Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5365-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si4700-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Sensor-EXP-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories SENSOR PUCK Manual de usuario

Silicon Laboratories

Silicon Laboratories Thunderboard EFM32GG12 Manual de usuario

Silicon Laboratories

Silicon Laboratories SLWRB4179B Manual de usuario

Silicon Laboratories

Silicon Laboratories Si53112 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si3474-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories C8051F064-EK Manual de usuario

Silicon Laboratories

Silicon Laboratories CP2104 Manual de usuario

Silicon Laboratories

Silicon Laboratories EZR32HG Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5328-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories TS3300 Manual de usuario

Silicon Laboratories

Silicon Laboratories Si1102EK Manual de usuario

Silicon Laboratories

Silicon Laboratories Si2493/57/34/15/04-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5342-EVB Manual de usuario

Silicon Laboratories

Silicon Laboratories Si5-EVB Series Manual de usuario

Silicon Laboratories

Silicon Laboratories Si4312 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario