Signet 8750-1 Manual de usuario

page 1 of 12‡ SIGNET 8750-1 pH/ORP Transmitter

pH/ORP

10.20 pH

25.0°C

ENTER

‡ SIGNET 8750-1 pH/ORP Transmitter ENGLISH

2. Speci ications

General

Compatible electrodes

+GF+ SIGNET 3-27XX/2720 pH/ORP Preamplifier/Electrode

Accuracy ± 0.03 pH, ± 2 mV ORP

Enclosure

• Rating NEMA 4X/IP65 front

• Case PBT

• Panel case gasket Neoprene

• Window Polyurethane coated polycarbonate

• Keypad Sealed 4-key silicone rubber

• Weight Approx. 325g (12 oz.)

Display

• Alphanumeric 2 x 16 LCD

• Contrast User selected, 5 levels

• Update rate 1 second

Electrical

• Power 12 to 24 VDC ±5%, regulated, 21 mA max.

Sensor input range

• pH 0.00 to 14.00 pH

• temp. 3K Balco, -25 to 120°C (-13 to 248°F)

• ORP -1000 to +2000 mV, isolated

(10KΩ I.D. resistance T+, T-)

Current output

• 4 to 20 mA, isolated, fully adjustable and reversible

3-8750.090-1

CAUTION!

• Remove power to unit before wiring input and

output connections.

• Follow instructions carefully to avoid personal injury.

1. Installation

ProcessPro transmitters are available in two styles panel mount and field mount. The panel mount is supplied with the necessary

hardware to install the transmitter. This manual includes complete panel mounting instructions.

Field mounting requires a separate mounting kit. The 3-8050 Universal kit enables the transmitter to be installed virtually

anywhere. Detailed instructions for field installation options are included with the 3-8050 Universal kit.

1.1 Panel Installation

1. The panel mount transmitter is designed for installation using a 1/4 DIN Punch. For manual panel cutout, an adhesive

template is provided as an installation guide. Recommended clearance on all sides between instruments is 1 inch.

2. Place gasket on instrument, and install in panel.

3. Slide mounting bracket over back of instrument until quick-clips snap into latches on side of instrument.

4. To remove, secure instrument temporarily with tape from front or grip from rear of instrument. DO NOT RELEASE.

Press quick-clips outward and remove.

Contents

1. Installation

2. Specifications

3. Electrical Connections

4. Menu Functions

SIDE VIEW

92 mm

(3.6 in.)

97 mm

(3.8 in.)

56 mm

(2.2 in.)

41 mm

(1.6 in.)

Optional

Rear

Cover

Field Mount Panel Mount

FRONT VIEW

96 mm

(3.8 in.)

96 mm

(3.8 in.)

quick-clips

gasket panel

terminals mounting

bracket

latch

Output -

Output +

System Pwr

Loop -

System Pwr

Loop +

Sensr Gnd

(SHIELD)

Sensr IN

(RED)

Sensr V+

(BLACK)

SIDE VIEW

Field Mount &

Panel Mount Panel Mount

Installation Detail

106 mm

(4.18 in.)

82 mm

(3.23 in.)

• Max loop impedance 50 Ω max. @ 12 V

325 Ω max. @ 18 V

600 Ω max. @ 24 V

• Update rate 0.5 seconds

• Accuracy ±0.03 mA @ 25°C, 24 V

Open-collector output

• Isolated, 50 mA sink or source, 30 VDC max. pull-up voltage

• Programmable for

• Hi or Lo w/adjustable hysteresis

• Proportional pulse (400 pulses per minute maximum)

Environmental

• Operating temperature -10 to 70°C (14 to 158°F)

• Storage temperature -15 to 80°C (5 to 176°F)

• Relative humidity 0 to 95%, non-condensing

• Maximum altitude 2000 m (6562 ft)

• Insulation category II

• Pollution degree 2

Standards and Approvals

• CSA, CE, UL listed

• Immunity EN50082-2

• Emissions EN55011

• Safety EN61010

• Manufactured under ISO 9001 and ISO 14001

C-3/01 English

page 2 of 12 ‡ SIGNET 8750-1 pH/ORP Transmitter

Output -

Output +

System Pwr

Loop -

System Pwr

Loop +

Earth

GND

Sensr Gnd

(SHIELD)

V-

(BLACK)

V+

(RED)

Temp -

(WHITE)

Temp +

(GREEN)

Iso. GND

(BLUE)

mV Input

(BROWN)

3. Electrical Connections

Caution: Failure to fully open terminal jaws before removing wire may permanently damage instrument.

Wiring Procedure

1. Remove 0.5 - 0.625 in. (13-16 mm) of insulation from wire end.

2. Press the orange terminal lever downward with a small screwdriver to open terminal jaws.

3. Insert exposed (non-insulated) wire end in terminal hole until it bottoms out.

4. Release orange terminal lever to secure wire in place. Gently pull on each wire to ensure a good connection.

Wiring Removal Procedure

1. Press the orange terminal lever downward with a small screwdriver to open terminal jaws.

2. When fully open, remove wire from terminal.

Terminals 1 and 2: Loop Power

12-24 VDC ±10% system power and current

loop output.

Max. loop impedance

50 Ω max. @ 12 V

325 Ω max. @ 18 V

600 Ω max. @ 24 V

Internal open-collector

output circuit

Output --

Output +

Isolation

15Ω

Terminals 3 and 4: Open-collector Output

A transistor output, programmable in CALIBRATE menu as

• High or Low setpoint with adjustable hysteresis

• Proportional pulse up to 400 pulses per minute

• May be disabled (Off) if not used.

Terminals 9-12: Sensor connections

9-10 are mV (pH or ORP) input from the electrode.

11-12 are Temperature input from the electrode

Terminals 5-8: Preampli ier power and grounds

5-6 are DC voltages from the 8750 to power the

preamplifier.

7-8 are ground terminals for the sensor and for earth

ground.

page 3 of 12‡ SIGNET 8750-1 pH/ORP Transmitter

3.1 System Power/Loop Connections

White (Temp)

Green (Temp)

Blue (ISO GND)

Brown (mV input)

Silver (Shield)

Black (V-)

Red (V+)

Preamp

+GF+ SIGNET 2720

pH Electrodes

+GF+ SIGNET 2714, 2714-HF

+GF+ SIGNET 2716

ORP Electrodes

+GF+ SIGNET 2715

+GF+ SIGNET 2717

* (connection of terminal 8 to Earth GND

may reduce electrical interference)

Terminals

Stand-alone application, no current loop used

Transmitter

Sys. Pwr.

Loop -

Sys. Pwr.

Loop +

Power Supply

DC 12 - 24 V

Power

Supply

Power

Supply

Connection to a PLC with built-in power supply

PLC

Power Supply

Ground

Power

Supply

Loop Input

4-20 mA

Loop Input

4-20 mA

Internal PLC

Connection

Connection to a PLC/Recorder, separate supply

Loop Input

4-20 mA in

Loop Input

4-20 mA in

DC 12 - 24 V

Power

Supply

Power

Supply

Example Two transmitter connected to PLC/Recorder

with separate power supply

Transmitter 2

DC 12 - 24 V

Power

Supply

Power

Supply

Transmitter 1

Transmitter

Sys. Pwr.

Loop -

Sys. Pwr.

Loop +

Transmitter

Sys. Pwr.

Loop -

Sys. Pwr.

Loop +

Sys. Pwr.

Loop -

Sys. Pwr.

Loop +

Sys. Pwr.

Loop -

Sys. Pwr.

Loop +

PLC or Recorder

Channel 1

4-20 mA in

Channel 1

4-20 mA in

Channel 2

4-20 mA in

Channel 2

4-20 mA in

Terminals Terminals

Terminals

PLC or Recorder

3.2 Sensor Input Connections

Wiring Tips:

• Do not route sensor cable in conduit containing AC power wiring. Electrical noise may interfere with sensor signal.

• Routing sensor cable in grounded metal conduit will help prevent electrical noise and mechanical damage.

• Seal cable entry points to prevent moisture damage.

• Only one wire should be inserted into a terminal. Splice double wires outside the terminal.

Transmitter

≤ 400 ft. (122 m)

page 4 of 12 ‡ SIGNET 8750-1 pH/ORP Transmitter

pH/ORP

10.20 pH

25.0°C

ENTER

VIEW menu

• During normal operation, ProcessPro displays the VIEW menu.

• When using the CALIBRATE or OPTIONS menus, ProcessPro will return to the VIEW menu if no activity

occurs for 10 minutes.

• To select the item you want displayed, press the UP or DOWN arrow keys. The items will scroll in a

continuous loop. Changing the display selection does not interrupt system operations.

• No key code is necessary to change display selection.

• Output settings cannot be edited from the VIEW menu.

•Proportional Pulsing

The Open Collector output will generate a 100 mS pulse at the

rate defined by settings in the CALIBRATE menu (see page 6)

In the example below

• The output will be 0 pulses/min. at pH values less than 5.0.

• The output will be 50 pulses/min. at 7.5 pH.

• The output will be 100 pulses/min. at pH values above 10 pH.

3.3 Open Collector Output

The Open Collector output can be used as a switch that responds

when the process value moves above or below a setpoint, or it

can be used to generate a pulsing signal with a rate proportional

to the process value.

•Low:

Output triggers when process variable is less than the setpoint.

The output will relax when the process moves above the setpoint

plus the hysteresis value.

•High:

Output triggers when process variable is greater than the

setpoint. The output will relax when the process variable moves

below the setpoint plus the hysteresis value.

Hysteresis

Time

Low Setpoint

Process

Hysteresis

Output active

Output inactive

Time

High Setpoint

Process

Open Collector Output ate:

0 to 100 Pulses/min.

endpoint

Pulse rate

0 pulses

100 pulses

Starting point

7.00 pH

12.6 ºCMonitor the Temperature input from the sensor.

This is the permanent view display.

All o the displays below are temporary. The permanent display will return a ter ten minutes.

Input:

307 mV

Loop Output:

14.16 mA

Last CAL:

06-30-01 >

EASY

CAL: >

Monitor the millivolt input from the electrode. Use this display to determine the

relative condition of your electrode during periodic calibration. (7 pH buffer = 0

mV, ±50 mV)

Monitor the 4-20 mA Loop output.

Monitor date for scheduled maintenance or date of last calibration.

Easy Cal is the fastest and simplest periodic calibration method. Requires 4 pH,

7 pH and 10 pH. (Any two)

View Menu or pH

Display Description

page 5 of 12‡ SIGNET 8750-1 pH/ORP Transmitter

Notes on Steps 5 and 6:

• All output functions remain active during editing.

• Only the flashing element can be edited.

• RIGHT ARROW key advances the flashing element in a continuous loop.

• Edited value is effective immediately after pressing ENTER key.

• If no key is pressed for 10 minutes unit will restore the last saved value and return to step 3.

• Step 6 (pressing ENTER key) always returns you to Step 3.

• Repeat steps 3-6 until all editing is completed.

Notes on Step 2:

If no key is pressed for 5 minutes while display is showing "Enter

Key Code", the display will return to the VIEW menu.

Notes on Steps 3 and 4:

• Refer to pages 6 and 7 for complete listing of menu items and their use.

• From the Step 3 display, pressing the UP and DOWN keys simultaneously will

return the display to the VIEW menu.

• If no key is pressed for 10 minutes, display will also return to the VIEW menu.

ProcessPro Editing Procedure:

Step 1. Press and hold ENTER key:

• 2 seconds to select the CALIBRATE menu

• 5 seconds to select the OPTIONS menu.

Step 2. The Key Code is UP-UP-UP-DOWN keys in sequence.

• After entering the Key Code, the display will show the first item in the selected menu.

Step 3. Scroll menu with UP or DOWN arrow keys.

Step 4. Press RIGHT ARROW key to select menu item to be edited.

• The first display element will begin flashing.

Step 5. Press UP or DOWN keys to edit the lashing element.

• RIGHT ARROW key advances the flashing element.

Step 6. Press ENTER key to save the new setting and return to Step 3.

OPTIONS

CALIBRATE

VIEW

2s 5s

Press &

hold for

access

ENTER

Step 5

Step 6

Notes on Step 1:

• The View Menu is normally displayed.

• The CALIBRATE and OPTIONS menus require a KEY CODE.

Step 4

First item in

CALIBRATE menu

Step 3

Step 3: Finished Editing?

Press the UP and DOWN keys simultaneously after

saving the last setting to return to normal operation.

Press the UP and DOWN keys simultaneously

while any element is flashing. This will recall the

last saved value of the item being edited and

return you to Step 3.

Step 5: Made an Error?

CALIBRATE: ----

Enter Key Code

CALIBRATE: *---

Enter Key Code

CALIBRATE: **--

Enter Key Code

CALIBRATE: ***-

Enter Key Code

Temperature >

Set:

10.0 pH >

Output Setpnt:

Temperature >

Set:

Output Setpnt:

0.00 pH

Output Setpnt:

0.00 pH

ENTER

Output Setpnt:

00.00 pH

Output Setpnt:

.00 pH

Output Setpnt:

Saving

Output Setpnt:

9.00 pH >

page 6 of 12 ‡ SIGNET 8750-1 pH/ORP Transmitter

Provides a maximum 25ºC offset to match temperature measurement to external reference.

Applies a linear offset to the pH measurement. The ideal value is the average pH of your

application. (A sample of your application at process temperature is recommended.)

Applies a slope to the pH measurement. The slope value and the standard value must be at

least 2 pH units apart.

The ideal values are the minimum and maximum values of your process.

Select the minimum and maximum values for the 4-20 mA Current loop output.

Select pH or Temperature as the source for the Open Collector Output.

Select the mode of operation for the Open Collector output High, Low or proportional Pulse.

The signal may be disabled if not in use.

In Low or High Mode, the Open Collector output will be activated when the pH reaches this

value.

In Low or High mode, the Open Collector output will be deactivated at Setpoint ± Hysteresis,

depending on High or Low Setpoint selection. (See details on page 4.)

If the output is in PULSE mode, set the start and end point of the range and also set the

maximum pulse rate. (The maximum PULSE rate setting is 400 pulses per minute.)

The combined Output Range and Pulse rate settings shown here indicate

"Start pulsing when the pH value is 4 and increase the pulse rate up to the maximum of 120

pulses per minute when the pH value reaches 8"

Use this “note pad” to record important dates, such as annual recertification or scheduled

maintenance.

Set:

Temperature >

Set:

Standard >

Set:

Slope >

Loop Range: pH

0.00 →14.00 >

Output Source:

pH >

Output Mode:

Low >

Output Setpnt:

4.00 pH >

Output Hys:

0.50 pH >

Output Range: pH

4.00 →8.00 >

Output PlsRate:

120 Pulses/min >

Last CAL:

06-30-01 >

Calibrate Menu or pH

Display

(Factory settings shown) Description

page 7 of 12‡ SIGNET 8750-1 pH/ORP Transmitter

Contrast:

Averaging:

Off >

Output Active:

Low >

Temp Display:

ºC>

Loop Adjust:

4.00 mA >

Loop Adjust:

20.00 mA >

Test Loop:

Test Output:

Adjust the LCD contrast for best viewing. A setting of 1 is lower contrast, 5 is higher.

Select lower contrast if the display is in warmer ambient surroundings.

OFF provides the most instantaneous output response to changes in input value.

LOW averaging = 4 seconds, HIGH averaging = 8 seconds of input signal.

Active HIGH This setting is used to turn a device (pump, valve) ON at the setpoint.

Active LOW This setting is used to turn a device OFF at the setpoint.

Select temperature units ºC or ºF.

Adjust the minimum and maximum current output. The display value represents the

precise current output.

Adjustment limits

• 3.80 mA < 4.00 mA > 5.00 mA

• 19.00 mA < 20.00 mA > 21.00 ma

Use this setting to match the 8750 loop output to any external device.

Press UP or DOWN keys to manually order any output current value from 3.6 mA to 21.00

mA to test current loop output.

Press UP or DOWN keys to manually toggle the state of the open collector output.

Options Menu or pH

Display

(Factory settings shown) Description

page 8 of 12 ‡ SIGNET 8750-1 pH/ORP Transmitter

Set:

Standard >

Set:

Slope >

Loop Range: mV

-1000 →+1000 >

Output Mode:

Off >

Output Setpnt:

-500 mV >

Output Hys:

10 mV >

Output Range: mV

-500 →+500 >

Output PlsRate:

120 pulses/min >

Last Cal:

06-30-01 >

Calibrate Menu or ORP

Display

(Factory settings shown) Description

Applies a linear offset to the ORP measurement. The ideal value is the average pH of your

application. (A sample of your application at process temperature is recommended.)

Applies a slope to the ORP measurement. The slope value and the standard value must be

at least 2 pH units apart. The ideal values are the minimum and maximum values of your

application.

Select the minimum and maximum ORP values for the 4-20 mA Current loop output.

Maximum settings are -1000 mV to +2000 mV.

Select the desired mode of operation for the Open Collector output High, Low or

proportional Pulse. The signal may also be disabled if not in use.

In Low or High Mode, the Open Collector output will be deactivated when the ORP reaches

this value.

In Low or High mode, the Open Collector output will be deactivated at Setpoint ± Hysteresis,

depending on High or Low Setpoint selection. (See details on page 4.)

If the output is in PULSE mode, set the start and end point of the range and also set the

maximum pulse rate. (The maximum PULSE rate setting is 400 pulses per minute.)

The combined Output Range and Pulse rate settings shown here indicate

"Start pulsing when the ORP value is -500 and increase the pulse rate up to the maximum

of 120 pulses per minute when the ORP value reaches +500"

Use this “note pad” to record important dates, such as annual recertification or scheduled

maintenance.

page 9 of 12‡ SIGNET 8750-1 pH/ORP Transmitter

Contrast:

Averaging:

Off >

Output Active:

Low >

Loop 1 Adjust:

4.00 mA >

Loop 1 Adjust:

20.00 mA >

Test Loop1:

Test Output1:

Adjust the LCD contrast for best viewing. A setting of 1 is lower contrast, 5 is higher.

Select lower contrast if the display is in warmer ambient surroundings.

OFF provides the most instantaneous output response to changes in input value.

LOW averaging = 4 seconds, HIGH averaging = 8 seconds of input signal.

Longer averaging produces more stable display and output response.

Active HIGH This setting is used to turn a device (pump, valve) ON at the setpoint.

Active LOW This setting is used to turn a device OFF at the setpoint.

Adjust the minimum and maximum current output. The display value represents the

precise current output.

Adjustment limits

• 3.80 mA < 4.00 mA > 5.00 mA

• 19.00 mA < 20.00 mA > 21.00 ma

Use this setting to match the 8750 loop output to any external device.

Press UP or DOWN keys to manually order any output current value from 3.6 mA to

21.00 mA to test current loop output.

Press UP or DOWN keys to manually toggle the state of the open collector output.

Options Menu or ORP

Display

(Factory settings shown) Description

page 10 of 12 ‡ SIGNET 8750-1 pH/ORP Transmitter

EASY CAL Procedure - pH

• This procedure simplifies system calibration using standard 4.0, 7.0, 10.0 pH buffers only. If these pH buffers are not available,

calibrate the system via the CALIBRATE menu, using the STANDARD and SLOPE settings.

• Access the CALIBRATE menu and set sensor temperature before performing EASY CAL for new electrode installations.

• Access EASY CAL menu from the view menu.

Theoretical mV values

pH @ 25°CmV

2 +296

3 +237

4 +177

5 +118

6 +59

7+0

8 -59

9 -118

10 -177

11 -237

12 -296

To Calibrate: Response:

To Accept:

Place electrode tip in

first pH buffer

pH 7.0 = 0 mV

pH 4.0 = 177

pH 10 = -177

Limit ± 50 mV

Allow for stabilization to accept

Place electrode tip

in second pH buffer.

Allow for stabilization

Press to accept

second buffer calibration.

ENTER

* 7.00 pH

-005 mV

* 6.90 pH

-005 mV

* 3.93 pH

+179 mV

30 seconds*

Press UP, UP, UP, DOWN buttons in sequence to enter menu,

XXXX will appear during code entry.

EASY CAL: ----

Enter Key Code

Place Sensor in

pH Buffer #1

Place Sensor in

pH Buffer #2

* 6.90 pH

-005 mV

* 3.93 pH

+179 mV

* 4.00 pH

+179 mV

_ _ _ _

To exit menus and return to

VIEW press UP and DOWN

button at the same time

Display returns to VIEW

Menu in 10 minutes or

when ENTER is pressed

Good Easy Cal

Press <ENTER>

EASY CAL Procedure - ORP

• This procedure simplifies system calibration using standard 4.0 pH and 7.0 pH buffers saturated with Quinhydrone. To calibrate

using any other ORP buffer solutions, use the Standard and Slope functions in the CALIBRATE menu.

• Access EASY CAL menu from the view menu.

*For best results, gently stir the submerged electrode for approximately 5 seconds during the stabilization period.

Large temperature differences from process fluids to buffers may require longer stabilization time.

Technical notes:

The difference between the actual mV and value shown is a good indication of the condition of the electrode.

Differences in excess of 50 mV may indicate a need to service the electrode.

To Calibrate: Response:

To Accept:

Place electrode tip

in first pH buffer;

pH7.0Å87mV

pH 4.0 Å 264 mV

Allow for stabilization to accept

Place electrode tip

in second (different)

pH buffer.

pH 4.0 Å 264 mV

pH7.0Å87mV

Allow for stabilization

Press to accept

second buffer calibration.

ENTER

* ORP: + 84 mV

Input: + 82 mV

30 seconds*

Press UP, UP, UP, DOWN buttons in sequence to enter menu,

will appear during code entry.

EASY CAL: ----

Enter Key Code

Place Sensor in

ORP Buffer #1

Place Sensor in

ORP Buffer #2

* ORP: + 84 mV

Input: + 82 mV

* ORP: + 87 mV

Input: + 82 mV

* ORP: +262 mV

Input: +260 mV

* ORP: +262 mV

Input: +260 mV

* ORP: +264 mV

Input: +260 mV

To exit menus and return to

VIEW press UP and DOWN

button at the same time

Display returns to VIEW

Menu in 10 minutes or

when ENTER is pressed

Good Easy Cal

Press <ENTER>

Tabla de contenidos

Otros manuales de Transmisor de Signet

Signet

Signet 8450-1 Manual de usuario

Signet

Signet 8550-3 Manual de usuario

Signet

Signet 9900 Manual de usuario

Signet

Signet 8550-1 Manual de usuario

Signet

Signet 8450-2 Manual de usuario

Signet

Signet 8150 Manual de usuario

Signet

Signet 8450-3 Manual de usuario

Signet

Signet 8550-1 Manual de usuario

Signet

Signet 8350-1 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario