Sierra Innova-Sonic 205 Manual de programación

Innova-Sonic® Model 205 Quick Start Instructions

Operation of Keyboard (Figure1-1)

9are the menu codes to input information

required for the flow measurement exercise.

You can use

to delete or move back to the

previous data.

/ +



/ -

are to toggle up and down the

menu.

After all data is selected, press

ENT

to confirm.

is used to select a menu using two-digit

numbers for each menu. For example, to enter pipe

outside diameter, select

1to enter into the window (ĀMENU11āis the address

code of the outer pipe diameter).

Transducer Connection˄Figure2-1˅Ǆ

(11)GND--PE ˄18 Ground ˅-˄DN˅screen wire ˄21 Ground ˅-˄UP˅screen wire

(12)L-- AC ˄19 Conductor˅- (DN) red wire-core ˄22 Conductor˅- (UP) red wire-core

(13)N --AC˄20 Shield Layer˅- (DN) black wire-core ˄23 Shield Layer˅- (UP) black wire-core

Note˖The upstream transducer cable is coded red and the downstream is blue.

Figure˄2-1˅Connection of the flow meter’s transducers

Measurement Site Selection ˄Figure2-2˅

Figure2-2 Installation at the 3 o’clock and 9 o’clock positions

Figure1-1 Keyboard

Select the measurement site on a straight section of pipe with 10D (10 pipe diameters)

upstream and 5D downstream. The transducers usually are installed at the site

3 o’clock and 9 o’clock positions, and avoid installation at 6 o’clock and 12 o’clock.

Installation and Debugging

Using this quick start installation procedure, the basic parameters needed for a quick startup can

be easily done (inputs, such as the pipe outside diameters, pipe wall thickness, pipe material, fluid

type, method of transducer installation, etc.). Also the distance (spacing) between the upstream

and downstream transducers is automatically calculated by the flow meter in order to obtain the

ultrasonic signal and to measure the flow. The main installation and debugging process as follows:

Power up the flow meter electronics

2: Select

1 and enter the outside pipe diameter

Select

2 and enter input the pipe wall thickness

Select

4 and choose the pipe material

5: Select

0 and choose the fluid type

6: Select

4 and choose the transducer mounting method

7: Select

5 and see the calculated transducer spacing

8: Use the calculated data for transducer spacing for installation

8.1 Pipe orientation and preparation (cleaning)

2 Applying coupling grease and mounting transducers

9: Select

0 and see the signal strength of the installed transducers.

(When the UP and DN signal strength is at least 60, the signal quality is at least 50, the flow meter

is functioning well.)

10:Select

1 to check TOM/TOS*100, (it should be 100f3% )

11: Select

0 to read the instantaneous and totalizing flow.

12: Select

5 and setup the data collection interval of SD card.

Note:

The information presented above is for quick start-up of the Sierra Innova-Sonic®

Model 205. Other setup parameters are referenced in the 205 manual.

For insertion transducer go to Innova-Sonic® Model 205 Manual

Appendix 4.

Edited 10/11/2009

Otros manuales para Innova-Sonic 205

Tabla de contenidos

Otros manuales de Instrumento de medición de Sierra

Sierra

Sierra InnovaMass 240 series Manual de usuario

Sierra

Sierra M100L Manual de usuario

Sierra

Sierra MaxTrak 180 Series Manual de usuario

Sierra

Sierra InnovaSonic 205i Manual de usuario

Sierra

Sierra Innova-Sonic 205 Manual de usuario

Sierra

Sierra Smart-Trak IM-100 Series Manual de usuario

Sierra

Sierra Top-Trak 820 Series Manual de usuario

Sierra

Sierra RedyIndustrial Series Manual de usuario

Sierra

Sierra InnovaSonic 205i Manual de usuario

Sierra

Sierra InnovaSonic 210 Manual de usuario

Sierra

Sierra QuadraTherm 640i Series Manual de usuario

Sierra

Sierra Accu-Mass 730 Manual de usuario

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra InnovaSonic 210 Manual de usuario

Sierra

Sierra 780 Series Manual de usuario

Sierra

Sierra InnovaMass 240 series Manual de usuario

Sierra

Sierra Innova-Flo 220 Series Manual de usuario

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra 760S Series Manual de usuario

Sierra

Sierra MaxTrak 180 Series Manual de usuario

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra Top-Trak 820 Series Instrucciones de funcionamiento originales

Sierra

Sierra BioTrak 645i Manual de usuario

Sierra

Sierra Multi-Trak 670S Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario