Sierra 780 Series Manual de usuario

Series 780-CT Instruction Manual Table of Contents

0-1

Sierra Series 780

Custody Transfer

Mass Flow Monitoring System

Instruction Manual

Part Number IM-78-CT

10.97 Revision B

5 Harris Court, Building L Monterey, CA 93940

(831) 373-0200 (800) 866-0200 Fax (831) 373-4402

http://www.sierrainstruments.com

Sierra Instruments b.v. Bolstoen 30A 1046 AV Amsterdam The Netherlands

31(0)20-6145810 Fax 31(0)20-6145815

Table of Contents Series 780-CT Instruction Manual

0-2

Customer Notice

Unless you have specifically ordered Sierra’s optional O2cleaning, this flow meter

may not be fit for oxygen service. Sierra Instruments, Inc., is not liable for any dam-

age or personal injury, whatsoever, resulting from the use of Sierra Instruments

standard mass flow meters for oxygen gas. You are responsible for cleaning the

mass flow meter to the degree required for your oxygen flow application.

No part of this publication may be copied or distributed, transmitted, transcribed, stored in

a retrieval system, or translated into any human or computer language, in any form or by

any means, electronic, mechanical, manual, or otherwise, or disclosed to third parties

without the express written permission of Sierra Instruments. The information contained in

this manual is subject to change without notice.

TRADEMARKS

Steel-TrakTM Collector-BoxTM and Flo-BoxTM are trademarks of Sierra Instruments Inc.

Other product and company names listed in this manual are trademarks or trade

names of their respective manufacturers.

Series 780-CT Instruction Manual Table of Contents

0-3

Table of Contents

Chapter 1 Introduction

Series 780-CT Mass Flow Monitoring System ....................1-1

Using this Manual.................................................1-1

Notes and Safety Information....................................1-1

Receipt of System Components .................................1-2

Technical Assistance..............................................1-2

How the Flow Monitoring System Works..........................1-3

Series 780-CT Mass Flow Meter Features.....................1-4

Series 900 Collector-Box Features..............................1-4

Chapter 2 Installation

Installation Overview..................................................2-1

Installing the Flow Monitoring Components.......................2-1

Flow Meter Installation Requirements..........................2-2

Flow Meter Orientation...........................................2-3

Flow Meter Installation...........................................2-3

Collector-Box Installation........................................2-4

Wiring Connections ...................................................2-5

Collector-Box Input Power Wiring .............................2-5

Sensor Wiring .....................................................2-6

Collector-Box Outputs ................................................2-7

Chapter 3 Operating Instructions

Facility Start Overview................................................3-1

Collector-Box Controls and Indicators..............................3-1

Display Selections.................................................3-2

Totalizer Reset.....................................................3-3

MODE Selections..................................................3-3

Function Selections ...............................................3-4

Numeric Keypad ..................................................3-4

Alarm Acknowledge ..............................................3-5

Status LEDs........................................................3-5

Operating the Flow Monitoring System.............................3-6

First Time Start Up................................................3-6

System Configuration.................................................3-7

Configuration Procedure .........................................3-7

Access Code Information........................................3-11

Table of Contents Series 780-CT Instruction Manual

0-4

Chapter 4 Validation and Maintenance Procedures

Field Validation Procedures ..........................................4-1

Sensor Test Procedures...........................................4-1

Electronic Test Procedures.......................................4-2

Entering Bias Factors..................................................4-4

Bias Factor Procedure ............................................4-5

Maintenance Procedures ..............................................4-6

Obtaining an RMA.....................................................4-7

Chapter 5 Troubleshooting

System Diagnostics....................................................5-1

Troubleshooting Procedures..........................................5-2

Appendix A Product Specifications

Specifications and Drawings .........................................A-1

List of Figures

1-1. Flow Monitoring System Block Diagram..................1-3

2-1. Correct Flow Meter Orientation.............................2-3

2-2. Collector-Box Mounting Dimensions ......................2-4

2-3. Flow Meter Wiring ...........................................2-6

2-4. Motherboard Terminal Block Layout/Output Wiring.....2-7

2-5. Relay Board Terminal Block Designations ................2-8

3-1. Collector-Box Front Panel Controls........................3-1

A-1. Collector-Box Critical Component Locations .............A-3

A-2. Collector-Box Standard Wiring.............................A-4

A-3. Collector-Box Optional Rack Mount Wiring ..............A-4

A-4. Digi-Bridge Board Critical Component Locations........A-5

List of Tables

2-1. Required Minimum Pipe Lengths for Installation.........2-2

Series 780-CT Instruction Manual Table of Contents

0-5

Warnings and Cautions

Agency approval for hazardous location installations varies between flow

meter models. Consult the factory for specific flow meter approvals be-

fore any hazardous location installation. For explosion proof installations,

you must use solid metal conduit and follow NFPA (or your local code)

approved wiring methods.

All installation procedures must be performed with the power Off.

All maintenance operations must be performed with the power Off. Be-

fore attempting any maintenance, verify no pressure is present in the

line. Gas leaks are possible during probe maintenance. Make sure the

lines are completely purged before removing the probe.

Calibration must be performed by qualified personnel. Sierra Instru-

ments, Inc. strongly recommends that you return your flow meter to the

factory for calibration.

The flow meter requires four wiring connections; two for power and two

for signal. The flow meter is not a 24 VDC, 4-20 mA loop powered trans-

mitter.

For all flow meter installations, standard industrial wiring practices apply.

Local codes may require the use of conduit. In general, we recommend

the use of conduit as a good wiring practice.

Although the meter will indicate flow in the opposite direction, it is calibrated

with flow in the direction indicated on the label. Confirm the meter is in-

stalled with flow in the same direction as the label. Measuring flow opposite

the calibration direction will result in inaccurate readings.

Before applying power for the first time, make sure all wiring is in compli-

ance with the instructions listed in Chapter 2.

The electronics, sensors and interconnecting wires supplied by Sierra In-

struments are calibrated as a single precision mass flow meter. Each

component is an integral part of the flow measurement circuit. Changing

the length of wires or interchanging sensors or sensor wiring will affect

the accuracy of the flow meter.

Table of Contents Series 780-CT Instruction Manual

0-6

Series 780-CT Instruction Manual Chapter 1 Introduction

1-1

Chapter 1 Introduction

Series 780-CT Mass Flow Monitoring System

The Sierra Series 780-Custody Transfer (CT) Mass Flow Monitor-

ing System precisely monitors the total accumulated mass flow of air

and process gases. The 780-CT Monitoring System features dual

level totalizing for tracking standard and premium flow rates. The

field-programmable totalizer automatically switches between normal

and premium billing rates based on the measured flow rate.

780-CT system components include a Sierra Series 780-CT Mass

Flow Meter with built in flow conditioning plates and a Sierra Series

900 Collector-Box™for computing totalized flow.

Using This Manual

This manual provides the information you need to install and operate

the 780-CT Mass Flow Monitoring System. The five chapters of

this manual cover these areas:

• Chapter 1 includes the introduction and product description

• Chapter 2 provides information needed for installation

• Chapter 3 describes system operation

• Chapter 4 covers system diagnostics and validation

• Chapter 5 outlines troubleshooting procedures

The product specifications and dimensional drawings are found in

Appendix A.

Note and Safety Information

We use note, caution and warning statements throughout this book

to draw your attention to important information.

Warning! Caution! Note

This statement appears with

information that is important to

protect people and equipment

from damage. Pay very close

attention to all warnings that

apply to your application.

This statement appears with

information that is important

for protecting your equipment

and performance. Read and

follow all cautions that apply

to your application.

This statement appears with

a short message to alert you

to an important detail.

Chapter 1 Introduction Series 780-CT Instruction Manual

1-2

Receipt of System Components

When receiving the components of the Sierra Flow Monitoring

System, carefully check the outside packing carton for damage in-

curred in shipment. If any carton is damaged, notify the local carrier

and submit a report to the factory.

Remove the packing slip and check that all ordered components are

present. Make sure any spare parts or accessories are not discarded

with the packing material. Do not return any equipment to the fac-

tory without a Return Material Authorization (RMA, see Chapter 4).

Technical Assistance

If you encounter a problem with your flow monitoring system, re-

view the configuration information for each step of the installation

and operation procedures. Verify that your settings and adjustments

are consistent with factory recommendations. Refer to Chapter 5,

Troubleshooting, for specific information and recommendations.

If the problem persists after following the troubleshooting proce-

dures outlined in Chapter 5, contact Sierra Instruments, Technical

Support at (800) 866-0200 or (831) 373-0200 between 8:00 a.m.

and 5:00 p.m. PST. When calling technical support, have the fol-

lowing information on hand:

•the flow meter serial number

•the Collector-Box serial number

•the flow range of the meter

•the software version number

•your Instruction Manual

•the problem you are encountering

Series 780-CT Instruction Manual Chapter 1 Introduction

1-3

How the Flow Monitoring System Works

Collector-Box

Series 780-CT

Mass Flow Meter

Series 900 Collector-Box

Flow Sensors

(Aligned 90-degrees to flow)

Heat

Gas Flow

Sensor Detail

Ts Ta

Figure 1-1. Flow Monitoring System Block Diagram

The 780-CT Mass Flow Meter measures gas flow using two sensing

elements–a velocity sensor and a temperature sensor that automati-

cally correct for changes in gas temperature. The digital sensor

bridge, Digi-bridge circuit heats the velocity sensor (Ts) at a con-

stant temperature differential above the gas temperature (Ta) and

measures the cooling effect of the gas flow. When heat is carried

away by the molecules in the gas, the heated sensor directly meas-

ures mass velocity (Ts-Ta), referenced to standard conditions of

70°F (21.1°C) and one atmosphere.

A supplied 5-wire cable connects between the flow meter sensor and

the Digi-bridge board inside the Collector-Box enclosure. This ca-

ble makes all the necessary power and signal connections.

Using data from the mass flow meter, the 900 Series Collector-Box

calculates the mass flow rate based on the power required to maintain

the constant temperature differential. The Collector-Box displays the

flow rate and totalized mass flow on a 2 x 16 digit LCD readout

screen. The Collector-Box provides both a 4-20 mA and 0-5 VDC

output signal proportional to mass flow.

Chapter 1 Introduction Series 780-CT Instruction Manual

1-4

Series 780-CT Mass Flow Meter Features

Series 780-CT mass flow meter bodies are constructed of 316L

stainless steel tubing. The 780 flow body incorporates special flow

conditioning plates welded into the body between the sensor and the

inlet connection. This unique dual-plate design eliminates velocity

profile distortions, swirl and temperature stratification in the gas

stream and greatly reduces upstream piping requirements.

Series 780-CT mass flow meters are available in a variety of process

connections depending on the flow meter ordered. Compression

fittings allow easy removal of the flow meter sensor probe for serv-

ice or maintenance procedures. The flow meter can be installed at a

remote location up to 350 feet from the Collector-Box.

Series 760HP/UHP and Series 780HP/UHP Mass Flow Meters are

also available with the Flow Monitoring System. The flow bodies

are constructed of 316L electropolished stainless steel tubing. The

“UHP” has a 7-10 Ra internal finish; the “HP” has 20-25 Ra. The

tubing’s smooth, level surface eliminates turbulence and erosive ac-

tion, which generates particulates. The Model 780HP/UHP flow

body incorporates flow conditioning plates that reduce upstream

piping requirements and improve measurement accuracy in con-

strained installations.

Series 900 Collector-Box Features

The Collector-Box’s flexible features allow you to customize your

flow monitoring and totalizing requirements. Local programming is

available via the 20-button, menu driven keypad along with the 2 x

16 character LCD display. The Collector-Box displays velocity,

standard volumetric flow, mass flow, total mass and time in user-

selectable engineering units. Comprehensive self-diagnostics, pro-

grammable testing and field calibration capabilities ensure accurate

flow rate monitoring.

The dual-totalizing feature allows you to set standard and premium

levels of flow monitoring. Pressing TOTAL on the front panel in-

terface displays the total units of flow. Press TOTAL a second time

to show the time elapsed. When pressing the TOTAL button a third

and fourth time, the same data is displayed for the premium level

totalizer showing the total premium flow and elapsed premium bill-

ing time.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Sierra

Sierra

Sierra InnovaSonic 210 Manual de usuario

Sierra

Sierra QuadraTherm 640i Series Manual de usuario

Sierra

Sierra Foundation Fieldbus 600 Series Manual de usuario

Sierra

Sierra InnovaMass 240i Series Manual de usuario

Sierra

Sierra Top-Trak 820 Series Instrucciones de funcionamiento originales

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra InnovaSonic 205i Manual de usuario

Sierra

Sierra InnovaSonic 210 Manual de usuario

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra Fast-Flo 620S Series Manual de usuario

Sierra

Sierra InnovaMass 240 series Manual de usuario

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra TM500 Manual de usuario

Sierra

Sierra QuadraTherm 640i Series Manual de usuario

Sierra

Sierra InnovaMass 241 series Manual de usuario

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra Side-Trak 830 Series Manual de usuario

Sierra

Sierra Profibus DP 600 Series Manual de usuario

Sierra

Sierra InnovaMass 240-V Manual de usuario

Sierra

Sierra QuadraTherm 640i Series Manual de usuario

Sierra

Sierra InnovaMass i Series Manual de usuario

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra Multi-Trak 670S Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario