Siemens SITRANS P DS III Manual de usuario

201 SOUTH HOUSTON AVE.

TULSA, OK 74127

PHONE (918) 584-4700

WWW.ERNIEGRAVES.COM

PRODUCT INSTRUCTION MANUAL V1.0

MAY 2016

SITRANS TANK LEVEL TRANSMITTER

MODELS: P DS III TANK

English ······························································································· 3

Français ··························································································· 49

Deutsch···························································································· 96

Español···························································································142

Italiano ····························································································189

Nederlands······················································································235

A5E03434626-03, 06/2013 3

SITRANS

Pressure transmitter

SITRANS P DS III (7MF4.33.. 7MF4.34.. 7MF4.35..)

Compact Operating Instructions

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The

notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage

have no safety alert symbol. These notices shown below are graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of

injury to persons with a safety alert symbol may also include a warning relating to property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific task in accordance with

the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their

training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products

and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage,

installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any

problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.

Introduction

1.1

Purpose of this documentation

These instructions are a brief summary of important features, functions and safety information, and contain all information

required for safe use of the device. It is your responsibility to read the instructions carefully prior to installation and

commissioning. In order to use the device correctly, first review its principle of operation.

The instructions are aimed at persons who mechanically assemble the device, connect it electrically, and start it up.

To achieve optimum usage of the device, read the detailed version of the manual.

See also

Instructions and manuals (http://www.siemens.com/processinstrumentation/documentation)

SITRANS P DS III (7MF4.33.. 7MF4.34.. 7MF4.35..)

4A5E03434626-03, 06/2013

1.2

History

This history establishes the correlation between the current documentation and the valid firmware of the device.

The documentation of this edition applies to the following firmware:

Edition

Firmware identifier nameplate

System integration

Installation path for PDM

06/2013 HART:

FW: 11.03.03, FW: 11.03.04,

FW: 11.03.05, FW: 11.03.06

PA: FW: 301.01.10

FF: FW: 11.01.01

SIMATIC PDM 8.x SITRANS P DSIII.2

1.3

Purpose

Overview

Depending on the version, a transmitter measures corrosive, non-corrosive and hazardous gases, vapors and liquids.

You can use the transmitter for the following types of measurement:

●Gauge pressure

●Absolute pressure

●Differential pressure

With appropriate parameter settings and the necessary add-on parts (e.g. flow orifices and remote seals), the pressure

transmitter can also be used for the following measurements:

●Level

●Volume

●Mass

●Volume of flow

●Mass flow rate

The output signal is always a load-independent direct current between 4 and 20 mA.

You can install the "intrinsically-safe" or "explosion-proof" version of the transmitter in hazardous areas. The devices have an

EC type examination certificate and comply with the appropriate harmonized European CENELEC directives.

Transmitters with remote seals of different shapes can be delivered for special applications. For example, measuring high-

viscosity substances is a special application.

Operate the device in accordance with the specifications in Section Technical specifications (Page 35).

For additional information, please refer to the operating instructions for the device.

SITRANS P DS III (7MF4.33.. 7MF4.34.. 7MF4.35..)

A5E03434626-03, 06/2013 5

1.4

Checking the consignment

1. Check the packaging and the device for visible damage caused by inappropriate handling during shipping.

2. Report any claims for damages immediately to the shipping company.

3. Retain damaged parts for clarification.

4. Check the scope of delivery by comparing your order to the shipping documents for correctness and completeness.

WARNING

Using a damaged or incomplete device

Danger of explosion in hazardous areas.

●

Do not use damaged or incomplete devices.

1.5

Nameplate layout

Nameplate with general information

The nameplate bearing the Order No. and other important information, such as design details and technical data, is on the

side of the enclosure.

①

Order number (machine-readable product code)

②

Serial number

Figure 1-1 Example of a nameplate

SITRANS P DS III (7MF4.33.. 7MF4.34.. 7MF4.35..)

6A5E03434626-03, 06/2013

Nameplate with approval information

On the opposite side is the nameplate with approval information. This nameplate shows e.g. the hardware and firmware

versions. You must also observe the information in the relevant certificate for a transmitter version for use in hazardous

areas.

①

Characteristics for hazardous area

⑤

Maximum surface temperature (temperature class)

②

Category for operating area

⑥

Device protection level

③

Type of protection

⑦

Firmware identifier

④

Group (gas, dust)

⑧

Hardware identifier

Figure 1-2 Example of a nameplate

1.6

Transportation and storage

To guarantee sufficient protection during transport and storage, observe the following:

●Keep the original packaging for subsequent transportation.

●Devices/replacement parts should be returned in their original packaging.

●If the original packaging is no longer available, ensure that all shipments are properly packaged to provide sufficient

protection during transport. Siemens cannot assume liability for any costs associated with transportation damages.

CAUTION

Insufficient protection during storage

The packaging only provides limited protection against moisture and infiltration.

●

Provide additional packaging as necessary.

Special conditions for storage and transportation of the device are listed in "Technical data" (Page 35).

1.7

Notes on warranty

The contents of this manual shall not become part of or modify any prior or existing agreement, commitment or legal

relationship. The sales contract contains all obligations on the part of Siemens as well as the complete and solely applicable

warranty conditions. Any statements regarding device versions described in the manual do not create new warranties or

modify the existing warranty.

The content reflects the technical status at the time of publishing. Siemens reserves the right to make technical changes in

the course of further development.

SITRANS P DS III (7MF4.33.. 7MF4.34.. 7MF4.35..)

A5E03434626-03, 06/2013 7

Safety instructions

2.1

Precondition for use

This device left the factory in good working condition. In order to maintain this status and to ensure safe operation of the

device, observe these instructions and all the specifications relevant to safety.

Observe the information and symbols on the device. Do not remove any information or symbols from the device. Always

keep the information and symbols in a completely legible state.

2.1.1

Warning symbols on the device

Symbol

Explanation

Consult operating instructions

2.1.2

Laws and directives

Observe the test certification, provisions and laws applicable in your country during connection, assembly and operation.

These include, for example:

●National Electrical Code (NEC - NFPA 70) (USA)

●Canadian Electrical Code (CEC) (Canada)

Further provisions for hazardous area applications are for example:

●IEC 60079-14 (international)

●EN 60079-14 (EC)

2.1.3

Conformity with European directives

The CE mark on the device is a sign of conformity with the following European directives:

Electromagnetic Compatibility EMC

2004/108/EC

Directive of the European Parliament and of the Council on the approximation of the

laws of the Member States relating to elec

tromagnetic compatibility and repealing

Directive 89/336/EEC.

Atmosphère explosible ATEX

94/9/EC

Directive of the European Parliament and the Council on the approximation of the

laws of the Member States concerning equipment and protective systems intend

for use in potentially explosive atmospheres.

Pressure Equipment Directive PED

97/23/EC

Directive of the European Parliament and of the Council on the approximation of the

laws of the Member States concerning pressure equipment.

The standards applied can be found in the EC declaration of conformity for the device.

2.2

Improper device modifications

WARNING

Improper device modifications

Danger to personnel, system and environment can result from modifications to the device, particularly in hazardous areas.

●Only carry out modifications that are described in the instructions for the device. Failure to observe this requirement

cancels the manufacturer's warranty and the product approvals.

2.3

Requirements for special applications

Due to the large number of possible applications, each detail of the described device versions for each possible scenario

during commissioning, operation, maintenance or operation in systems cannot be considered in the instructions. If you need

additional information not covered by these instructions, contact your local Siemens office or company representative.

SITRANS P DS III (7MF4.33.. 7MF4.34.. 7MF4.35..)

8A5E03434626-03, 06/2013

Note

Operation under special ambient conditions

We highly recommend that you contact your Siemens representative or our application department

before you operate the

device under special ambient conditions as can be encountered in nuclear power plants or when the device is used for

research and development purposes.

2.4

Use in hazardous areas

Qualified personnel for hazardous area applications

Persons who install, assemble, commission, operate and service the device in a hazardous area must have the following

specific qualifications:

●They are authorized, trained or instructed in operating and maintaining devices and systems according to the safety

regulations for electrical circuits, high pressures, aggressive and hazardous media.

●They are authorized, trained, or instructed in carrying out work on electrical circuits for hazardous systems.

●They are trained or instructed in maintenance and use of appropriate safety equipment according to the pertinent safety

regulations.

WARNING

Unsuitable device for the hazardous area

Danger of explosion.

●

Only use equipment that is approved for use in the intended hazardous area and labelled accordingly.

See also

Technical specifications (Page 35)

WARNING

Loss of safety of device with type of protection "Intrinsic safety Ex i"

If the device has already been operated in non-intrinsically safe circuits or the electrical specifications have not been

observed, the safety of the device is no longer ensured for use in hazardous areas. There is a danger of explosion.

●Connect the device with type of protection "Intrinsic safety" solely to an intrinsically safe circuit.

●

Observe the specifications for the electrical data on the certificate and in Chapter "Technical data (Page 35)".

WARNING

Use of incorrect device parts in potentially explosive environments

Devices and their associated device parts are either approved for different types of protection or they do not have

explosion protection. There is a danger of explosion if device parts (such as covers) are used for devices with explosion

protection that are not expressly suited for this type of protection. If you do not adhere to these guidelines, the test

certificates and the manufacturer warranty will become null and void.

●Use only device parts that have been approved for the respective type of protection in the potentially explosive

environment. Covers that are not suited for the "explosion-proof" type of protection are identified as such by a notice

label attached to the inside of the cover with "Not Ex d Not SIL".

●

Do not swap device parts unless the manufacturer specifically ensures compatibility of these parts.

WARNING

Risk of explosion due to electrostatic charge

To prevent the build-up of an electrostatic charge in a hazardous area, the key cover must be closed during operation and

the screws tightened.

The key cover may be opened temporarily at any time for the purposes of operating the transmitter, even during plant

operation; the screws should then be tightened again.

SITRANS P DS III (7MF4.33.. 7MF4.34.. 7MF4.35..)

A5E03434626-03, 06/2013 9

Installing/mounting

3.1

Basic safety instructions

WARNING

Wetted parts unsuitable for the process media

Danger of injury or damage to device.

Hot, toxic and corrosive media could be released if the process medium is unsuitable for the wetted parts.

●Ensure that the material of the device parts wetted by the process medium is suitable for the medium. Refer to the

information in "Technical data" (Page 35).

WARNING

Incorrect material for the diaphragm in Zone 0

Danger of explosion in the hazardous area. In the case of operation with intrinsically safe supply units of category "ib" or

devices of the flameproof enclosure version "Ex d" and simultaneous use in Zone 0, transmitter explosion protection

depends on the tightness of the diaphragm.

●Ensure that the material used for the diaphragm is suitable for the process medium. Refer to the information in the

section "Technical specifications (Page 35)".

WARNING

Unsuitable connecting parts

Danger of injury or poisoning.

In case of improper mounting hot, toxic and corrosive process media could be released at the connections.

●

Ensure that connecting parts (such as flange gaskets and bolts) are suitable for connection and process media.

Note

Material compatibility

Siemens can provide you with support concerning selection of sensor components wetted by process media. However, you

are responsible for the selection of components. Siemens accepts no liability for faults or failures resulting from incompatible

materials.

WARNING

Exceeded maximum permissible operating pressure

Danger of injury or poisoning.

The maximum permissible operating pressure depends on the device version. The device can be damaged if the operating

pressure is exceeded. Hot, toxic and corrosive process media could be released.

●Make sure that the device is suitable for the maximum permissible operating pressure of your system. Refer to the

information on the nameplate and/or in "Technical specifications (Page 35)".

WARNING

Exceeded maximum ambient or process media temperature

Danger of explosion in hazardous areas.

Device damage.

●Make sure that the maximum permissible ambient and process media temperatures of the device are not exceeded.

Refer to the information in Chapter "Technical specifications (Page 35)".

SITRANS P DS III (7MF4.33.. 7MF4.34.. 7MF4.35..)

10 A5E03434626-03, 06/2013

WARNING

Open cable inlet or incorrect cable gland

Danger of explosion in hazardous areas.

●Close the cable inlets for the electrical connections. Only use cable glands or plugs which are approved for the relevant

type of protection.

WARNING

Incorrect conduit system

Danger of explosion in hazardous areas as result of open cable inlet or incorrect conduit system.

●In the case of a conduit system, mount a spark barrier at a defined distance from the device input. Observe national

regulations and the requirements stated in the relevant approvals.

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario