Siemens QAX32.1 Manual de usuario

CA2N1641

en_03

2015

-12-23

Building Technologies

1641

Desigo

™ RX

Room unit with PPS2

interface

QAX32.1

for use with:

– devices of the ranges Desigo RXC, RXB, RXL, and RXA (PPS2)

–Desigo PX Automation stations 1)

– devices with a PPS2 interface

•Room temperature measurement

•Room temperature setpoint adjuster

•Control mode selector switch ( / Auto)

•PPS2 interface to controller

•Socket for commissioning and service tool or service terminal

Use

The room unit is used in rooms controlled by an individual room control system, to

measure the room temperature and for operation of a room controller.

It can also be used in conjunction with a Desigo PXC… automation station 1).

The room unit incorporates a socket for a commissioning and service tool or service

terminal. This tool socket provides access via the PPS2 interface or via a bus system

(e.g. LONWORKS® bus) to the connected individual room controller.

1) If room units QAX32.1, QAX33.1, QAX34.1 or QAX84.1 are used in conjunction with a PXC

automation station, the room unit will show the request of the user and not the effective state.

2/6

Siemens QAX32.1 – Room unit with PPS2 interface CA2N1641en_03

Building Technologies 2015-12-23

Ordering

When ordering, please specify the quantity, product name and type code.

Example:

30 Room units QAX32.1

Equipment combinations

The room unit is suitable for use in conjunction with all controllers which incorporate a

PPS2 room unit interface (e.g. Desigo RX, Desigo PX).

Mechanical design

The room unit is designed for surface mounting (with knock-outs for cable entry from

the top or bottom) or for mounting on a recessed conduit box with the cables connected

from the rear.

The unit comprises a housing and base unit, connected by releasable snap-fittings.

The base unit accommodates the screw terminals which have an integrated terminal

strip.

The housing accommodates a printed circuit board, room temperature sensor element,

setpoint adjuster, rocker switch for mode selection, plug-in connectors and a socket for

the commissioning and service tool or service terminal.

Both the housing and base are made of plastic.

Base unit

Housing

80082

80084

Socket for the commissioning

and service tool or service

terminal

80167A

Dial for stepless adjustment of the setpoint

LEDs to indicate control mode

Rocker switch for mode selection

The controller control mode can be selected on the basis of occupancy, using the

rocker switch on the room unit (press left or right arrow). The current control mode is

indicated by a LED.

Position

Control mode 1)

The controller operates at the setback setpoints (at night, or when room is

unoccupied or occupied intermittently)

Auto

Comfort mode (room occupied)

1) For details of these functions, refer to the application description for the relevant controller range.

Operator controls

and indication

Rocker switch for mode

selection

3/6

Siemens QAX32.1 – Room unit with PPS2 interface CA2N1641en_03

Building Technologies 2015-12-23

01884

Address plugs inside the housing

They allow setting the address in cases where several

room units are connected to one controller.

The room units are delivered with address 1.

Disposal

The device is classified as waste electronic equipment in terms of the European

irective 2012/19/EU (WEEE) and should not be disposed of as unsorted municipal

waste

The relevant national legal rules are to be adhered to.

Regarding disposal, use the systems setup for collecting electronic waste.

Observe all local and applicable laws.

Engineering notes

The device receives its power from the connected controller via the PPS2 interface

(extra low voltage). Only one room unit may be connected to a RX… room controller.

A maximum of 5 room units may be connected to a PXC… automation station (they are

identified by different settings of their address plugs)

A twisted-pair cable is required for the connection to the controller.

Desigo RX uses four-core cables, Desigo PX uses two-core cables (see the respective

installation guides). Screening is not required.

Mounting

•The room unit is suitable for wall-mounting and for mounting on a recessed conduit

box.

•Do not mount in recesses, shelves, behind curtains or doors, or above or near heat

sources.

•Avoid exposure to direct sunlight or draughts.

•The electrical wiring conduit must be sealed where it joins the room unit, to prevent

the occurrence of draughts in the conduit which could affect the sensor.

•The specified ambient conditions must be complied with.

•Mounting instructions are printed on the room unit packaging.

•A mounting kit is included with the unit.

Installation notes

Local installation regulations must be observed.

The room unit is not protected against connection to AC 230 V.

Address plugs

STOP

Note!

4/6

Siemens QAX32.1 – Room unit with PPS2 interface CA2N1641en_03

Building Technologies 2015-12-23

Commissioning notes

After an interrupt of the PPS2 interface the communication will only be re-established

when the connected controller polls the PPS2 addresses. The duration of the

corresponding cycle is:

RXA: 10 sec; RXB, RXL and RXC: 3 min; PX: 30 sec.

The following routine occurs in the room unit when the power supply is connected (via

the PPS2 interface) or after a reset via the controller:

Step

Function

Description

LED test

The LEDs are operated in sequence for 1 s each

2 Device

ready

After a delay of 1 s the device will be ready for PPS2

communication. The actual control mode is displayed after a

further delay of 5 s.

Technical data

Supply voltage

Operating voltage range

DC 12...15 V

(SELV)

DC 12…15 V class 2 (US)

The room unit receives its power from the connected controller, via the PPS2 interface

Power consumption (from controller)

Max. 0.10 VA

Function data

Temperature sensor

Measuring element

NTC resistor

Measuring range

0 ... 40 °C

Response time

≤8 min

Accuracy (5 ... 30 °C)

±0.5 K

Accuracy (25 °C)

±0.25 K

Setpoint correction

Correction range (determined by controller)

max. ±12 K (default ±3 K)

Accuracy over full correction range

10 %

Indication (control mode)

2 LEDs, yellow

Interfaces

Type of interface between controller and

room unit

PPS2

(point-to-point interface, Version 2)

Baud rate

4.8 kbit/s

Cable connections

Connection terminals (screw terminals)

Stranded or solid conductors

0.8 ... 2.5 mm

Single cable length controller

– Room unit

See Installation guidelines:

Desigo

RXC: CA110334,

Desigo

RXB & RXL: CM110381

Desi

go RXA: CA2Z3884

Desigo PX: CA110396

Cable type

-core or 4-core, twisted pairs,

unscreened

Connecting cable for service tool

Off-the-shelf, max. 3 m

Protection data

Housing protection

IP 30 to EN 60529

Protection class

III to EN 60730-1

Ambient conditions

IEC 721

Operation

Transport

Ambient air conditions

Class 3K5

Class 2K3

Temperature

0 ... 50 °C

– 25 ... 70 °C

Humidity

< 85 %rH

< 95 %rH

Mechanical conditions

Class 3M2

Class 2M2

Response on start-up

5/6

Siemens QAX32.1 – Room unit with PPS2 interface CA2N1641en_03

Building Technologies 2015-12-23

Standards, directives

and

approvals

Product standard

EN 60730-1

Automatic electrical controls for

household and similar use

Electromagnetic compatibility (Applications)

For use in residential, commerce, light

industrial and industrial environments

EU conformity (CE)

CA2T1741xx *)

UL certification (US)

UL916, http://ul.com/database

RCM-conformity (EMC)

A5W00005055 *)

EAC conformity

Eurasia conformity

Environmental

compatibility

Product environmental declaration (co

ntains

data on RoHS compliance, material

s compo-

sition, packaging, environmental benefit,

disposal)

A6V10736277_en

--_a *)

Dimensions

See “Dimensions”

Color

Housing front, dial

NCS S 0502-G, ≈RAL 9003 signal white

Housing, base unit, rocker switch

RAL 7035 light grey

Weight

Excluding packaging

0.12 kg

*) The documents can be downloaded from http://siemens.com/bt/download.

Connection

terminals

The tool socket on the room unit provides access to the connected individual room

controller via the commissioning and service tool or the service terminal.

The bus cable (Terminals 3 and 4) is therefore looped to the tool socket (Pins 1 and 2).

The bus cable is not affected by the room unit.

For connection of a service terminal, the PPS2 interface (Terminals 1 and 2) is also

connected to the tool socket.

87654321

C–

C+

CP–

CP+

80085

PPS2 interface, supply voltage

CP+ 1 Device supply, Data PPS2 (pos.)

CP– 2 Device supply, Data PPS2 (neg.)

Bus connection (looped to tool socket)

C+ 3 With LONWORKS® bus (Desigo RXC): CLA

C– 4 With LONWORKS® bus (Desigo RXC): CLB

5 ... 8 Not used

Standard type RJ45 tool socket.

3206Z01

2 3 4 5 6 7 8

With L

ORKS

® bus (Desigo RXC): CLA

With LONWORKS® bus (Desigo RXC): CLB

Not used

CP+ Data PPS2

CP– Data PPS2

Terminal layout

Tool socket

6/6

Siemens QAX32.1 – Room unit with PPS2 interface CA2N1641en_03

Building Technologies 2015-12-23

Connection diagram (Example: RXC)

The following example shows the room unit connected to a Desigo RXC room

controller:

1741A03

PPS2

Tool

7 8 1 2

4321

C–

C+

CP–

CP+

CP–

CLA

CLB

PPS2

LonWorks® Bus

= Twisted pair

R1 Room unit QAX32.1

N1 Room controller RXC...

A Connection for RXT10 commissioning and service tool

B Connection for service terminal with PPS2 interface

Dimensions

9,5

4,2

80087

100

Published by:

Siemens Switzerland Ltd.

Building Technologies Division

International Headquarters

Gubelstrasse 22

6301 Zug

Switzerland

Tel. +41 41

-724 24 24

www.siemens.com/buildingtechnologies

Delivery and technical specifications subject to change

All dimensions in mm

Tabla de contenidos

Otros manuales de Controladores de temperatura de Siemens

Siemens

Siemens RCC10U Manual del propietario

Siemens

Siemens TALON Manual de usuario

Siemens

Siemens RAV12 series Manual de usuario

Siemens

Siemens REA23.03RF Manual de usuario

Siemens

Siemens QAA2290.EWSC Manual de usuario

Siemens

Siemens SIMATIC Manual de usuario

Siemens

Siemens RDX42.22U Manual del propietario

Siemens

Siemens 1000 series Manual de usuario

Siemens

Siemens 2200 Series Manual de usuario

Siemens

Siemens RDE series Manual de usuario

Siemens

Siemens REV23.03RF Manual de usuario

Siemens

Siemens REV23.03RF Manual de usuario

Siemens

Siemens RCU50U Manual del propietario

Siemens

Siemens 24RFDC/SET Manual de usuario

Siemens

Siemens SITRANS TSinse rt Guía del administrador

Siemens

Siemens QAX30.1 Manual de usuario

Siemens

Siemens RDF20U Manual de usuario

Siemens

Siemens QAA910 Manual de usuario

Siemens

Siemens RLM162 Manual de usuario

Siemens

Siemens REV24 Manual de usuario

Siemens

Siemens HEATWELL RDE Series Manual del operador

Siemens

Siemens QAA24 Manual de usuario

Siemens

Siemens SITRANS TSinse rt Guía del administrador

Siemens

Siemens REA23.03RF Manual de usuario

Manuales populares de Controladores de temperatura de otras marcas

Swegon

Swegon LUNAd MB Manual de usuario

Lucky Reptile

Lucky Reptile Thermo Control II Manual de usuario

SENSORMETRIX

SENSORMETRIX Argon 100 Manual de usuario

Fuji Electric

Fuji Electric PXE4 Manual de usuario

Yuyao gongyi

Yuyao gongyi XMT-808 series Manual de usuario

Selec

Selec TC544C Manual de usuario

P.W. KEY

P.W. KEY rt-208gt Manual de usuario

Future Design

Future Design FDC-9200 Manual de usuario

BH Thermal

BH Thermal BriskONE Manual de usuario

Omron

Omron E5EX-H Manual de usuario

West Control Solutions

West Control Solutions KS 45 Guía de inicio rápido

MCS

MCS RITC-15B Manual de usuario

SMC Networks

SMC Networks Thermo-con INR-244-639 Manual de usuario

eltherm

eltherm Ex-TC It Series Manual de usuario

Omron

Omron C200H-TV Series Manual de usuario

industrie technik

industrie technik CA1 Manual de usuario

KRAL

KRAL EET 32 Manual de usuario

dixell

dixell XR420C Diagrama de cableado