Siemens QAA73 Manual de usuario
Pag. 1/5
17.10.2008 Service instructions Lmu34 sw 2.09
Condensing gas boilers
NOVADENS …
USING THE SIEMENS TEMPERATURE
REGULATOR QAA73 TO PROGRAM
BOILERS PARAMETERS
GB
Pag. 2/5
17.10.2008 Service instructions Lmu34 sw 2.09
The editable parameters are those between 504 and 652 (parameters 650 and 652 are reading only
parameters).
Proceed as follows to access this parameters:
1) Simultaneously press keys 1-4on QAA73 temperature regulator for about 3 seconds. The
“Initialising BMU parameters” appears on the display (line 725).
2) Simultaneously press keys 1-2on QAA73 temperature regulator for about 3 seconds. The
“Initialising BMU SERVICE” (line 504 “TkSmax”).
3) Press keys 1-2to scroll through the list of parameters.
4) To change the value of the selected parameter, press key 3-4 to decrease or increase the value
respectively.
5) Press key 5 to enter the new values and exit programming of the boiler’s electronic main board.
1
2
3
4
5
DEFAULT PARAMETERS LIST
NOVADENS
1.240
240
280
QAA73
parameters
Description of parameters
24
kW
20/24 kW
24/28 kW
Pag. 3/5
17.10.2008 Service instructions Lmu34 sw 2.09
504
Maximum flow setpoint temperature (°C)
80
516
Summer / winter changeover temperature
30
532
Heating curve slope heating circuit HC1
15
534
Room temperature adjustment (°C)
0
536
Maximum speed (rpm) at maximum output in heating mode
(maximum speed limitation)
5900
4300
5050
541
Maximum degree of modulation in heating mode (%)
100
60
74
544
Overrun time (s) of pumps
180
545
Minimum burner pause time (s)
(heat demand-dependent switching hysteresis)
180
555.0
Chimney sweep function
ON =active
OFF=deactivate
OFF
555.1
Legionella function
ON =active
OFF=deactivate
ON
555.2
Setting
ON = hydraulic differential pressure switch
OFF = pressure switch
OFF
555.3…555.7
NOT used
-
608
Setting value of modulation air at ignition load (PWM%),
55
50
55
609
Setting value of modulation (PWM%) air at low-fire; lower limit
modulation range
15
11
16
610
Setting value of modulation (PWM%) air at high-fire; upper limit
modulation range
100
88
100
611
Setting value of required speed (rpm) at ignition load
4500
4300
4400
612
Setting value of required speed (rpm) at low-fire
1850
1600
2000
613
Setting value of required speed (rpm) at high-fire
5900
5100
5900
DEFAULT PARAMETERS LIST
NOVADENS
1.240
240
280
QAA73
parameters
Description of parameters
24
kW
20/24 kW
24/28 kW
Pag. 4/5
17.10.2008 Service instructions Lmu34 sw 2.09
614
Open Therm input setting (QAA73)
0= only with QAA73
1= with Low Voltage room thermostat RT or QAA73
2= factory default –only for LUNA IN models
0
641
Setting value post purge time (s)
10
677
Preset output BMU (controller stop function)
max = 100 %
min = 0 %
0
678
MANUFACTURE information
205
202
205
651
Hydraulic system adjustment
1
2
652
MANUFACTURE information
1240
2242
2280
ONLY READING PARAMETERS
700 **
1st previous fault code counter
-----
702
1st internal previous fault code
-----
703 **
2nd previous fault code counter
-----
705
2nd internal previous fault code
-----
706 **
3rd previous fault code counter
-----
708
3rd internal previous fault code
-----
709 **
4th previous fault code counter
-----
711
4th internal previous fault code
-----
DEFAULT PARAMETERS LIST
NOVADENS
1.240
240
280
QAA73
parameters
Description of parameters
24
kW
20/24 kW
24/28 kW
Pag. 5/5
17.10.2008 Service instructions Lmu34 sw 2.09
712 **
5th previous fault code counter
-----
714
5th internal previous fault code
-----
715
Actual fault code counter
-----
** The counter shows the number of times of same error happened
728
HMI code of 1st previous error counter
-----
729
HMI code of 2nd previous error counter
-----
730
HMI code of 3rd previous error counter
-----
731
HMI code of 4th previous error counter
-----
732
HMI code of 5th previous error counter
-----
733
HMI code of actual error counter
-----
Tabla de contenidos
Otros manuales de Controladores de temperatura de Siemens
Siemens
Siemens RLA162 Manual de usuario
Siemens
Siemens RDF20U Manual de usuario
Siemens
Siemens QAA24 Manual de usuario
Siemens
Siemens QAX910 Manual de usuario
Siemens
Siemens SIMATIC Manual de usuario
Siemens
Siemens RCU50U Manual del propietario
Siemens
Siemens REA22 Manual del operador
Siemens
Siemens HEATWELL RDE Series Manual del operador
Siemens
Siemens SITRANS TS100 Guía del administrador
Siemens
Siemens BPS242RF Manual de usuario
Siemens
Siemens RDF110 Manual de usuario
Siemens
Siemens RDJ10RF/SET Manual de usuario
Siemens
Siemens 24RFDC/SET Manual de usuario
Siemens
Siemens RDH10RF/SET Manual de usuario
Siemens
Siemens 1000 Series Manual de usuario
Siemens
Siemens RDX Series Manual de usuario
Siemens
Siemens RDF210 Manual de usuario
Siemens
Siemens RDE10 Series Manual de usuario
Siemens
Siemens REA23 Manual de usuario
Siemens
Siemens RDJ10RF/SET Manual de usuario
