Siemens DB-HR Manual de usuario

P/N 315-033220-5

DETECTOR AND BASE PLACEMENT

Detector and base locations shall follow the drawings provided or approved

by Siemens Industry, Inc. or its authorized distributors.This is extremely

important! The detector placements shown on these drawings were chosen

after a careful evaluation of all facets of the protected area. When drawings

are not available, refer to Detector Placement section of detector Installation/

Wiring Instructions and to NFPA 72, National Fire Alarm Code and CAN/ULC-

S524.

BASE WIRING

The Model DB-HR from Siemens Industry, Inc. is a polarity insensitive detector

base and works with HFP-11, HFPT-11, HFPO-11, SFP-11*, SFPT-11* and SFPO-

11* detectors only. Detectors should be interconnected as shown in Figure 1

and wired to the DLC (refer to DLC Installation Instructions, P/N 315-033090), FS-

DLC (refer to FS-250 Installation, Operation and Maintenance Manual, P/N 315-

049353) or FDLC (refer to FS-250C Installation, Operation and Maintenance

Manual, P/N 315-049589C), as applicable. Line 1 and Line 2 can be either line of

the loop. Note any limitations on the number of detectors and restrictions

on the use of remote devices permitted for each circuit.

Figure 1

DB-HR Wiring Diagram Using HFP-11 Series and SFP-11 Series Detectors

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

*THE RELAY CONTACTS ARE

SHOWN IN THE NON-ALARM/

SYSTEM RESET CONDITION.

LINE 1 AND LINE 2 CAN BE EITHER LINE OF THE LOOP.

DO NOT USE AN END

OF LINE DEVICE

TO NEXT DEVICE

DO NOT USE AN END

OF LINE DEVICE

TO NEXT DEVICE

TO INITIATING CIRCUIT

OF SIEMENS INDUSTRY,

INC. CONTROL PANEL

REMOTE RELAY BASE

MODEL DB-HR

LINE 1

LINE 2

LINE 1

LINE 2

RELAY*

CONTACTS

3A, 120 VAC

3A, 30 VDC

DB-HR RELAY BASE

Detector Base

Installation Instructions

Model DB-HR

*SFP-11, SFPT-11 and SFPO-11 detectors are approved for use in Canada only.

DETECTOR MOUNTING USING THE DB-HR BASE

The detector is provided with a separate base which attaches to a standard 4

inch square or a 4 inch octagonal electrical box, with the box size and depth

required by the NEC for the number and size of conductors used. Wire size:

max – 14 AWG, min – 18 AWG.

Refer to Figure 2.

1. Route all wires outward from outlet box.

2. When the ALARM LED viewing is critical, position the LED mark in the

base in the intended direction.

3. Route wires through the hole in the center of the base and mount base

to outlet box. Make connections directly to the base terminals. Refer to

Figures 1 and 2 for details.

4. After all bases are installed, check wiring integrity.

5. To insure proper installation of the detector head into the base:

a. Route wires away from connector terminals.

b. Take up all slack in the outlet box.

c. Properly dress and position all wires flat against the base.

d. Check that screw terminals are tight.

P/N 315-033220-5

Figure 2

Mounting the Base

BASE

MOUNTING

HOLES

MOUNTING

HOLE COVERS

ALARM LED

LOCATION WITH

DETECTOR

INSTALLED

IN BASE

Tabla de contenidos

Otros manuales de Sensor de seguridad de Siemens

Siemens

Siemens DB721 Manual de usuario

Siemens

Siemens L-852A-D Dualite Manual de usuario

Siemens

Siemens SINUMERIK 840D sl TCU 30.3 Manual de usuario

Siemens

Siemens Cerberus PRO OH720 Manual de usuario

Siemens

Siemens DBS721 Manual de usuario

Siemens

Siemens FDOOT221 Manual de usuario

Siemens

Siemens Intrunet IS392 Manual de usuario

Siemens

Siemens QRB Series Manual de usuario

Siemens

Siemens RAR Series Manual de usuario

Siemens

Siemens Cerberus CS1140 Guía

Siemens

Siemens AD-3I Manual de usuario

Siemens

Siemens FDO421 Manual de usuario

Siemens

Siemens HI320C Instrucciones de funcionamiento e instalación

Siemens

Siemens IR100B Manual de usuario

Siemens

Siemens QNA2 D Series Guía

Siemens

Siemens 5SM6011-1 Manual de usuario

Siemens

Siemens FDB22 Series Manual de usuario

Siemens

Siemens DELTA i-system 1,1 Komfort 5TC1 505 Manual de usuario

Siemens

Siemens UP 255D21 5WG1 255-2DB21 Manual de servicio

Siemens

Siemens SBGA-34 Manual de usuario

Siemens

Siemens SICAM V01.00 Manual de usuario

Siemens

Siemens FDM243H Manual de usuario

Siemens

Siemens ANT 3 Guía del administrador

Siemens

Siemens FDOOT441 Manual de usuario

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario

Solinst

Solinst 301 Manual de usuario