Siemens FDOOT271 Guía

FDOOT271, FDB271

Radio fire detector, detector base

Mounting

A6V10227637_j_en_-- Smart Infrastructure

2020-03-31

Imprint

Technical specifications and availability subject to change without notice.

Transmittal, reproduction, dissemination and/or editing of this document as well as

utilization of its contents and communication thereof to others without express

authorization are prohibited. Offenders will be held liable for payment of damages.

All rights created by patent grant or registration of a utility model or design patent

are reserved.

Issued by:

Siemens Switzerland Ltd.

Smart Infrastructure

Global Headquarters

Theilerstrasse 1a

CH-6300 Zug

Tel. +41 58 724-2424

www.siemens.com/buildingtechnologies

Edition: 2020-03-31

Document ID: A6V10227637_j_en_--

Imprint

2 | 22 A6V10227637_j_en_--

A6V10227637_j_en_-- 3 | 22

Table of contents

1 About this document................................................................................. 5

1.1 Applicable documents .............................................................................. 5

2 Mounting/Installation............................................................................... 6

2.1 Required space ........................................................................................ 6

2.2 Detector base FDB271 ............................................................................. 7

2.3 Installing the radio fire detector FDOOT271............................................. 8

2.4 Detector locking device FDBZ293 ............................................................ 10

2.5 Designation plate FDBZ291 ..................................................................... 11

2.6 Detector dust cap FDZ291 ....................................................................... 12

2.7 Detector base seal RS720........................................................................ 13

2.8 Establishing factory settings ..................................................................... 14

3 Details for ordering ................................................................................... 15

3.1 Radio fire detector FDOOT271................................................................. 15

3.2 Detector base FDB271 ............................................................................. 15

3.3 Battery pack BAT3.6-10 ........................................................................... 15

3.4 Detector locking device FDBZ293 ............................................................ 16

3.5 Designation plate FDBZ291 ..................................................................... 16

3.6 Detector dust cap FDZ291 ....................................................................... 16

3.7 Detector base seal RS720........................................................................ 17

4 Specifications ........................................................................................... 18

4.1 Technical data .......................................................................................... 18

4.2 Dimensions............................................................................................... 20

4.3 Environmental compatibility and disposal................................................. 20

4 | 22 A6V10227637_j_en_--

1 About this document

Goal and purpose

This document contains all the information required to install detector base

FDB271 and radio fire detector FDOOT271.

Prerequisites:

● The installation location of the radio fire detector has been established.

● Mounting should be performed by a specialist in compliance with safety

regulations.

You will find more information on the radio fire detector in document

A6V10227635'Technical Manual Radio fire detector FDOOT271'.

You will find information on how to integrate the radio fire detector into a radio cell

in document A6V10227639'Technical manual Radio gateway FDCW241'.

Intended use

The radio fire detectorFDOOT271 may only be used in a detector baseFDB271

and together with a radio gatewayFDCW241 in a fire detection system FS20/

FS720.

1.1 Applicable documents

Document ID Title

001508 Guidelines Connection factors, line resistances and

capacitances for fire detection systems collective,

AnalogPLUS, interactive, FDnet

008331 List of compatibility (for 'Sinteso™' product line)

009409 Data sheet Colored detectors, bases and base

attachment FDO.., FDOOT…, FDT…, FDB…, FDCW241

010030 Application guideline Sinteso Fire detectors

A6V10208552 Installation Detector locking device FDBZ293

A6V10227631 Planning Radio fire detection system SWING

A6V10227637 Installation Radio fire detector FDOOT271, Detector base

FDB271

A6V10227639 Technical manual Radio gateway FDCW241

A6V10227643 User Guide SWING-Tool FXS2061

A6V10229261 List of compatibility (for 'Cerberus™ PRO' product line)

A6V10254740 Operating instructions Solo461 heat detector tester kit

RE7T

A6V10271323 Data sheet SWING Neural radio fire detector FDCW241,

FDOOT271, FDM273, FDM275, FDM275(F)

A6V10367669 Open-Source Software (OSS) Licenses SWING

About this document

Applicable documents 1

A6V10227637_j_en_-- 5 | 22

2 Mounting/Installation

2.1 Required space

● Upon insertion of the detector, the detector base is stressed by compression,

tension and torsion. The fixing must thus be designed accordingly.

● Detector bases must be placed flat on the ceiling.

● Avoid mounting on steps, concrete ribs, etc.

● When selecting the installation position, take into account any structures that

may impair radio reception.

● There must be at least 50cm of free space below and at least 2cm to the

sides of the detector, so that the detector can be removed with the detector

exchanger.

● Contorted detector bases complicate or even impede the insertion of the

detectors with the detector exchanger.

* = min. 2 cm

min. 50 cm

Figure 1: Minimum spacing when installing detector bases

Mounting/Installation

Required space

6 | 22 A6V10227637_j_en_--

2.2 Detector base FDB271

The detector base must be securely connected to the substructure.

Screw the detector base securely onto the substructure using two screws.

2 2

46 mm

90 mm

Figure 2: Mounting the detector base

1 Detector base

2 Screws with max.Ø of 4mm

3 Holder for detector locking device

4 Switching cam

Mounting/Installation

Detector base FDB271 2

A6V10227637_j_en_-- 7 | 22

2.3 Installing the radio fire detector FDOOT271

The action of inserting the radio fire detector into the detector base activates it;

the detector then logs on to other radio devices immediately. Therefore, start from

the radio gateway and work outwards to install the individual radio fire detectors.

Figure 3: Mounting the radio fire detector

1 Battery pack BAT3.6-10 1 4 Battery cable

2 Inserting the battery pack 5 Battery connector

3 Holder

1Not included in the scope of delivery

The flashing behavior of the internal alarm indicator is described in the 'Internal

alarm indicator' chapter.

wThe radio gateway has been activated and switched to maintenance mode.

wThe radio fire detector is set to the factory settings. [➙14]

wYou have the battery pack and the required accessories to hand.

wThe detector base FDB271 is mounted. [➙7]

1. Install the accessories you require.

2. Label the new battery pack(1) with the current date.

3. Connect the battery connector(5) of the new battery pack.

4. Insert the new battery pack(1), paying attention to the position of the battery

cable (arrows at4).

Mounting/Installation

Installing the radio fire detector FDOOT271

8 | 22 A6V10227637_j_en_--

5. Make sure that the holder(3) latches into place correctly.

aWhen the battery connector is connected, the internal alarm indicator lights

up red for 5seconds.

aAfter a further 10seconds, the radio fire detector signals that it is not

installed on the detector base and the internal alarm indicator flashes. If it

flashes red, this indicates the factory settings. If it flashes green, this

indicates that the radio fire detector has already been logged on to a radio

gateway.

aIf this does not happen, this means the battery pack is defective and must

not be used.

6. Insert the radio fire detector into the detector base.

aThe internal alarm indicator flashes green and the radio fire detector is

logged on to the radio gateway.

aIf the process of logging on to the radio gateway is successful, the internal

alarm indicator stops flashing.

aThe radio fire detector is now installed and is ready for commissioning.

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario

Solinst

Solinst 301 Manual de usuario