Siemens SIM-16 Manual de usuario
Siemens Building Technologies
Fire Safety
P/N 315-034060-3
A24205-A334-B825
Supervised Input Module (500-034060 / S24235-B112-A2)
Installation Instructions
Model SIM-16
INTRODUCTION The SIEMENS Model SIM-16 Supervised Input Module
is a remotely located, general purpose input module. It
provides sixteen input circuits for remote system
monitoring. Each input can be individually programmed
as supervised (dry contacts only) or unsupervised
(general-purpose input). The SIM-16 has two Form C
relays. The relays and the inputs are programmable using
the Zeus Programming Tool.
OPERATION The SIM-16 is mounted in an enclosure that is remotely
located from the Main Panel. Communication between
the SIM-16 and the NIC-C (Network Interface Card) or
the next CAN module (in CE applications) is through the
Control Area Network (CAN) bus. Up to 99 SIM-16s can
be used with a single NIC-C or a DAC-NET (in CE
applications).
Each SIM-16 has two 10-position rot ary switches that
are used to set the board address on the CAN which is
a sub-address of the NIC-C or the DAC-NET (in CE
applications).
Every time a change of state of the input is detected, a
unique CAN message is sent to the NIC-C (DAC-NET).
A CAN message from the NIC-C (DAC-NET) directed
to the SIM-16 controls the Form C relays.
PRE-INSTALLATION Rotary Address Switches - Set the board address for
each SIM-16 using both of the ten-position rotary
switches located on the board (See Figure 1). Each of
these addresses must be a sub-address of the NIC-C
or the DAC-NET (in CE applications) and must be the same as the addresses
assigned in the Zeus Programming Tool.
Figure 1
SIM-16 Supervised Input
Module
12345678
12345678
910111213141516
910111213141516
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
TB2
TB1
P2
S1 S2
P3
TB3
1
1
6
6
TB4
SIM-16
Siemens Building Technologies
Fire Safety
P/N 315-034060-3
A24205-A334-B825
2
INSTALLATION A SIM-16 may be installed in a REMBOX or in an enclosure on mounting plate MP-
OM (in CE applications). When using REMBOX 2 or 4, mount the SIM-16 in one
module space on a REMBOX2-MP, P/N 500-634211 or REMBOX4-MP, P/N 500-
634212 using the four screws provided. (Refer to REMBOX2-MP/REMBOX4-MP
Installation Instructions, P/N 315-034211.) Up to 4 SIM-16s will fit in a REMBOX2;
up to 8 SIM-16s will fit in a REMBOX4.
WIRING Refer to Figures 2-6.
Disconnect BATTERY and AC prior to working on equipment.
• Each SIM-16 module is a node in the CAN bus.
• The SIM-16 can be inst alled with or without an RNI. Connect the CAN bus
and 24V as shown in Figures 2 and 3.
• Up to 99 CAN modules, in any combination, can be connected to the CAN
bus of each NIC-C or the CAN bus of the DAC-NET (in CE applications).
• Each SIM-16 module is shipped with one CCS cable.
•Cable connections for SIM-16 modules are shown in the following t able:
SNOITCENNOCELBAC61-MIS
elbaCnoitpircseDrebmuNtraPnoitcennoC
LCCgnoL-ELBAC-NAC
-6,)mc001(.ni03
rotcudnoc
412436-995
6K-1A-53242C
oslA.61-MIStsrifotINRno4PstcennoC
/MCFot61-MISmorfstcennoc
.)roodno(seludomBSC/MCS/MCL
SCCtrohS-ELBAC-NAC
-6,)mc41(.ni½5
rotcudnoc
935331-555
4K-1A-53242C
ro61-MISotseludom61-MISstcennoC
worelgnisaniseludom61-MCO
The CAN bus requires a 120Stermination at each end of the loop. Refer to the NIC-C
Installation Instructions, P/N 315-033240 / A24205-A334-B824 or DAC-NET Installation
Instructions P/N 315-035100 / A24205-A334-B839 for details about CAN termination.
Siemens Building Technologies
Fire Safety
P/N 315-034060-3
A24205-A334-B825
3
Figure 3
SIM-16 Wiring Without An RNI
NOTES
1. All wiring supervised.
2. All wiring power limited to
NFPA 70 per NEC 760.
3. Wiring for TB1 and TB2 is
18 AWG (1.0mm2) min.,
12 AWG (4mm2) max.
4. Wiring for TB3 and TB4 is
26 AWG (∅ 0.25mm) min.,
16 AWG (1.5mm2) max.
5. CAN network max. line
resistance 16S.
6. Refer to the NIC-C
Installation Instructions, P/N
315-033240 / A24205-
A334-B824 for CAN
network termination
instructions.
Figure 2
SIM-16 CAN Bus Connections With An RNI
Siemens Building Technologies
Fire Safety
P/N 315-034060-3
A24205-A334-B825
4
Figure 4
SIM-16Relay Connections
NOTES
1. Contacts are unsupervised.
2. 1A max @ 24VDC resistive.
3. All wiring must remain
inside the enclosure or
within 20 feet (6.5m) in
rigid conduit.
4. Wiring for TB1 and TB2 is
18 AWG (1.0mm2 ) min.,
12 AWG (4mm2) max.
5. Wiring for TB3 and TB4 is
26 AWG (∅ 0.25mm) min.,
16 AWG (1.5mm2) max.
6
5
4
3
2
1
COM
N.C.
N.O.
COM
N.C.
N.O.
Relay 1
Relay 2
TB3
1
6
TB4
SIM-16
87654321
16 15 14 13 12 11 10 9
TB2
ELECTRICAL RATINGS
tnerruCenalPkcaBV420
tnerruCV42lanimreTwercS
Am02
tupnidesivrepus/Am2.1+
yalerevitca/Am02+
tnerruCenalPkcaBV2.60
tnerruCybdnatSV42
Am02
tupnidesivrepus/Am2.1+
yalerevitca/Am02+
Siemens Building Technologies
Fire Safety
P/N 315-034060-3
A24205-A334-B825
5
Figure 5
SIM-16 Supervised Input Wiring
NOTES
1. All inputs supervised.
2. All inputs power limited to
NFPA 70 per NEC 760.
3. Wiring for TB1 and TB2 is
18 AWG (1.0mm2 ) min.,
12 AWG (4mm2) max.
4. Maximum distance 500 feet
(165m) from SIM-16 to
supervised input.
5. In the Zeus Programming
Tool, select supervised for
each supervised input.
6. Supervised and unsuper-
vised inputs may be mixed
on a single SIM-16.
Figure 6
SIM-16 Unsupervised Input Wiring
NOTES
1. All inputs unsupervised.
2. All inputs power limited to
NFPA 70 per NEC 760.
3. Wiring for TB1 and TB2 is
18 AWG (1.0mm2 ) min.,
12 AWG (4mm2) max.
4. All inputs must remain
inside the enclosure or
within 20 feet (6.5m) in
rigid conduit.
5. In the Zeus Programming
Tool, select unsupervised for
each unsupervised input.
6. Supervised and unsuper-
vised inputs may be mixed
on a single SIM-16.
12345678
87654321
910111213141516
16 15 14 13 12 11 10 9
SIM-16
TB1
TB2
TYPICAL
CONNECTION
(16 PLACES)
*6.8K
*SUPPLIED WITH
THE SIM-16
INPUT #2
INPUT #6
INPUT #16
INPUT #5
INPUT #9
12345678
87654321
910111213141516
16 15 14 13 12 11 10 9
SIM-16
TB1
TB2
TYPICAL
CONNECTION
(16 PLACES)
INPUT #2
INPUT #1
INPUT #6
INPUT #16
INPUT #5
INPUT #9
Siemens Building Technologies
Fire Safety
P/N 315-034060-3
A24205-A334-B825
6
Siemens Building Technologies, Inc.
8 Fernwood Road
Florham Park, New Jersey 07932
Siemens Building Technologies, Ltd.
2 Kenview Boulevard
Brampton, Ontario L6T 5E4 CN
P/N 315-034060-3
A24205-A334-B825
Siemens AG
I BT DE FS SYS
D-81379 München
For CE applications in Cerberus E100 systems refer to
Installation Instruction A24205-A334-B844 (English) or A24205-A334-A844 (German).
Tabla de contenidos
Otros manuales de Sistema de E/S de Siemens
Siemens
Siemens 6ES7141-6BG00-0BB0 Documento técnico
Siemens
Siemens SIMATIC ET 200S Manual de usuario
Siemens
Siemens SIMATIC ET 200iSP Manual de usuario
Siemens
Siemens SIMATIC ET 200M Manual de usuario
Siemens
Siemens TALON Series Manual del producto
Siemens
Siemens 262E01 Manual de usuario
Siemens
Siemens 6ES7521-1BL00-0AA0 Manual de usuario
Siemens
Siemens Simatic S7-1500 Documento técnico
Siemens
Siemens SIMATIC ET 200SP Manual de usuario
Siemens
Siemens EA12 Manual de usuario
Siemens
Siemens SICAM AI Manual de usuario
Siemens
Siemens SIMATIC ET 200SP Manual de usuario
Siemens
Siemens Simatic S7-1500 Manual de lista de piezas
Siemens
Siemens FDCIO422 Manual de servicio
Siemens
Siemens SIMATIC ET 200S Manual de usuario
Siemens
Siemens SIMATIC ET 200S Manual de usuario
Siemens
Siemens SIMATIC ET 200eco PN Documento técnico
Siemens
Siemens SIMATIC ET 200S Manual de usuario
Siemens
Siemens SIMATIC IM151-1 STANDARD Manual de usuario
Siemens
Siemens SIMATIC ET 200AL Documento técnico
Manuales populares de Sistema de E/S de otras marcas
WAGO
WAGO 750-344 Manual de usuario
Teknim
Teknim TWM-1887 Manual de instrucciones
Intelligent Appliance
Intelligent Appliance IA-2662-E Manual de usuario
BERGHOF
BERGHOF ECC DIO 16/16 Manual de instrucciones
Advantech
Advantech PCM-27J3AU Manual de instalación y operación
Festo
Festo CP-E08-M12-CL Manual de usuario
