Siemens BACnet PTEC Dual Duct 2 AVS Manual de usuario

Installation Instructions

Document No. 550-139

October 26, 2016

BACnet PTEC Dual Duct 2 AVS

Controller

Generic Controller I/O Layout. See Wiring Diagram for application specific details.

Item No. 550-139. Rev. CA Page 1 of 6

Control Applications

6665 through 6669

Product Description

These instructions explain how to field install or

replace a Siemens BACnet PTEC Dual Duct 2 AVS

Controller.

Warning/Caution Notation

WARNING

Personal injury/loss of life may

occur if you do not follow the

procedures as specified.

CAUTION

Equipment damage or loss of

data may occur if you do not

follow the procedures as

specified.

Product Numbers

Siemens BACnet PTEC Dual Duct

2 AVS Controller

550-497PA

Shipping carton includes a controller assembly, a

mounting rail, and two self-tapping/drilling screws.

Document No. 550-139

Installation Instructions

October 26, 2016

Page 2 of 6Siemens Industry, Inc.

CAUTION

Keep the unit in its static-proof

bag until installation.

Otherwise, you run the risk of

damage to the printed circuit

board from electrostatic

discharge.

Accessories

Low cost temporary

temperature sensor, 10K

thermistor with RJ11 (1”

long), that enables space

control if the permanent room

or duct sensor is not installed

(pack of 25).

540-658P25

Duct Temperature Sensor,

NTC 10K Ω Type 2, 3" Probe

for Commissioning only

QAM1030.008P50

Expected Installation Time

New controller installation

10 Minutes

Replacement (old controller has

removable terminal blocks)

6 Minutes

Replacement (old controller does

not have removable terminal

blocks)

16 Minutes

NOTE:

You may require additional time for

database work at the field panel.

Required Tools and Equipment

Small flat-blade screwdriver (1/8-inch blade

width)

Cabling and connectors

Cordless drill/driver set

ESD wrist strap

Prerequisites

Wiring conforms to NEC and local codes and

regulations. For further information see the

Wiring Guidelines Manual

(125-3002).

Room temperature sensor installed (optional).

24 Vac Class II power available.

Supply power to the unit is OFF.

Any application specific hardware or devices

installed.

Air velocity sensors installed in ducts.

NOTE:

If the controller is being installed on a

box with 1 or more stages of electric

heat, the 550-809 MOV with pre-

terminated spade connectors must be

installed across the manufacturer-

supplied airflow switch. MOVs can be

installed at the time the controller is

factory mounted; coordinate with the

box manufacturer prior to order

placement. For field installation, see

Metal Oxide Varistor Kit Installation

Instructions

(540-986).

NOTE:

A low-cost temporary RTS (540-

658P25) is available that plugs into the

RTS port on the controller, providing

temperature input and actual space

control until a permanent RTS is

installed.

Installation Instructions

NOTE:

All wiring must conform to national and

local codes and regulations (NEC, CE,

etc.).

1. Secure the mounting rail in the controller’s

desired location.

2. Place the ESD wrist strap on your wrist and

attach it to a good earth ground.

3. Remove the controller from the static proof bag

and snap it into place on the mounting rail.

Document No. 550-139

Installation Instructions

October 26, 2016

Siemens Industry, Inc. Page 3 of 6

4. Connect the FLN.

5. Connect the point wiring (see

Wiring Diagram

s).

6. Plug the room temperature sensor cable into the

RTS port.

7. Connect the power trunk. DO NOT apply power

to the controller without first consulting the

specialist. This TEC is designed to work with 2-

wire AC power (Neutral and Phase (hot) at 24

Vac +/-20%. Use of the earth terminal is optional

and if used it should be connected to the nearest

earth ground (building steel, conduit or duct work

(if earthed)).)

CAUTION

It is very important that the

neutral that supplies the TEC

be earth grounded at the source

of the 24 Vac power.

Possible erratic equipment

operation or damage if neutral

is left floating.

The installation is complete.

Wiring Diagrams

CAUTION

The controller’s DOs control 24

Vac loads only. The maximum

rating is 12 VA for each DO. An

external interposing relay is

required for any of the following:

• VA requirements higher than

the maximum

• 110 or 220 Vac requirements

• DC power requirements

• Separate transformers used to

power the load

(for example part number 540-

147, Terminal Equipment

Controller Relay Module)

Document No. 550-139

Installation Instructions

October 26, 2016

Page 4 of 6Siemens Industry, Inc.

Wiring for AI with a 4 to 20 mA Sensor.

NOTE:

If the voltage/current switch is set to

current and a 4 to 20 mA sensor is

connected to an AI, then special

wiring requirements must be followed.

NOTE:

When wiring any actuator that uses a 0 to

10V control signal and ties AC neutral to DC

common, an additional wire must connect

the actuator AC neutral to the DC common

of the PTEC/TEC AO being used to control

the actuator.

24 Vac Modulating Control.

Actuator

Symbol

TEC

Connection

Function

Terminal

Connection

Standard

Color

Supply (SP)

Red

Neutral (SN)

Black

AO3 –15

(+)

0 to 10V

input signal

Gray

C to AO3

16 (-)

Common

jumper

Document No. 550-139

Installation Instructions

October 26, 2016

Siemens Industry, Inc. Page 5 of 6

Applications 6665, 6666, 6667, and 6668 with Hot

Water Reheat.

Applications 6665, 6666, 6667, and 6668 with Electric

Auxiliary Reheat.

Document No. 550-139

Installation Instructions

October 26, 2016

Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as

design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners. ©

2016 Siemens Industry, Inc.

Siemens Industry, Inc.

Building Technologies Division

1000 Deerfield Parkway

Buffalo Grove, IL 60089-4513

USA

Tel. 1 + 847-215-1000

Your feedback is important to us. If you have

comments about this document, please send them

to SBT_technical.editor.us.sbt@siemens.com.

Document No.550-139

Printed in the USA

Page 6 of 6

Application 6669 –Variable Air Volume with

Changeover with Hot Water Reheat.

Cyber security disclaimer

Products, solutions and services from Siemens

include security functions to ensure the secure

operation of building automation and control, fire

safety, security management, and physical security

systems. The security functions on these products,

solutions and services are important components of

a comprehensive security concept.

Drafting, implementing and managing a

comprehensive and up-to-date security concept,

customized to individual needs, is nevertheless

necessary, and may result in additional plant- or

site-specific preventive measures to ensure secure

operation of your site regarding building automation

and control, fire safety, security management, and

physical security. These measures may include, for

example, separating networks, physically protecting

system components, user training, multi-level

defensive measures, etc. For additional information

on security as part of building technology and our

product, solution and service offerings, please

contact your Siemens sales representative or project

department. We strongly recommend to always

comply with our security advisories on the latest

security threats, patches and other related

measures. http://www.siemens.com/cert/en/cert-

security-advisories.htm

Tabla de contenidos

Otros manuales de Controladores de Siemens

Siemens

Siemens 540-716 Manual de servicio

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SFA21/18 Manual de usuario

Siemens

Siemens Powermite 599 MT Series Manual del propietario

Siemens

Siemens SIMATIC Mobile Client900WXN Manual de usuario

Siemens

Siemens CU240E-2 Manual de usuario

Siemens

Siemens CP 1612 A2 Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens GPC 1A Series Manual de usuario

Siemens

Siemens SQL36E65 Manual de usuario

Siemens

Siemens 3RA2220 Manual de usuario

Siemens

Siemens SIRIUS M200D Manual de usuario

Siemens

Siemens S7-1200 TELECONTROL Guía del usuario

Siemens

Siemens ATC5300 Instrucciones de montaje

Siemens

Siemens OpenAir GBB161.1U Manual del propietario

Siemens

Siemens SITOP UPS1600 Manual de usuario

Siemens

Siemens SIMATIC S5-90U Guía del usuario

Siemens

Siemens SIMATIC S7-200 Manual de usuario

Siemens

Siemens SCALANCE M800 Manual de usuario

Siemens

Siemens 7SR224 Manual de usuario

Siemens

Siemens Ecofast 3RK1 323-2AS54-1AA0 Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens Sirius 3RA6 Guía del usuario

Siemens

Siemens S7-1200 TELECONTROL Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

3M MicroTouch EX113 Manual de usuario