Siemens ZIC-4AC Manual de usuario

A24205-A334-B827 s

P/N 315-035850-2

Installation Instructions

Model ZIC-4AC

Zone Interface Card (500-035850 / S24235-B110-A2)

INTRODUCTION The Model ZIC-4AC from Siemens Building

Technologies, Inc., is a zone interface card that

provides notification appliance circuits (NAC) for

the system. It has 4 outputs that can be

configured for Class A or Class B and control of

audible and visual notification appliances such as

speakers, strobes, horns, bells, etc.

Each zone can be configured independently for

different usages as programmed in the Zeus tool

and can be controlled automatically by program

logic or manually using the PMI. During the initial

power-up condition, each zone on the ZIC-4AC is

configured as a steady NAC, Class A configuration

with 2A current limit. The ZIC-4AC then sends a

message to the PMI indicating that it is

unconfigured.

The ZIC-4AC supports one or two channel bulk

amplification as well as synchronized and non-

synchronized strobes. This selection is available in

the Zeus tool under the detail properties for each

ZIC-4AC circuit. Synchronization across multiple

ZIC-4AC cards is automatic as a part of the

system operating characteristics.

Features ZIC-4AC features are as follows:

• Zones can be configured independently for

audio or strobe use

• Zones can be configured independently for

Class A or Class B

• Can have independent input sources for each

output

• Zone input voltage supervision

• Zone output supervision

• Intelligent self-restoring power limiting

• Coded signal synchronization capability

• Card level Ground Fault detection

• Communicate CAN protocol

• Uploadable firmware update

• Ability to pass through up to 4A per circuit

Figure 1

ZIC-4AC Zone

Interface Card

A24205-A334-B827

P/N 315-035850-2

OPERATION The ZIC-4AC contains four Class A circuits. Each circuit is rated at 4A at

24VDC and has an input connected to the power source and an output where

the NAC devices are connected. The zone inputs are isolated from one

another and are supervised for the presence of power. This allows the use of

different power sources with different ground references. The zone output is

supervised for open and short circuit conditions while the zone is inactive and

allows different combinations of output configurations (Standard NAC or

Speaker) per card. Each ZIC-4AC card occupies any one card slot in the CC-

5/CC-2 cardcage. The ZIC-4AC also has the capability to detect ground fault

on its zone output as indicated by a diagnostic LED.

Strobe unsynchronized:

Input 1is connected directly to output 1, output is ON steady. Same for In-

/Outputs 2, 3 and 4

Strobe synchronized:

Input 1 is connected directly to output 1, Output is ON for about 1 second,

then a ZIC-4AC onboard relay switch output polarity (+24V is now GND and

GND is now +24V). This will cause the strobes to flash. All ZIC-4AC outputs

configured as strobe sync will switch output polarity at the same time, also

outputs from other ZIC-4AC. Same for In-/Outputs 2, 3 and 4

Bulk amplification 1 channel:

Input 1is connected directly to output 1, output is ON steady. Same for In-

/Outputs 2, 3 and 4

Bulk amplification 2 channel:

This mode provides the possibility to choose between two different signal

for one speaker line. Signal one (A) has to be connected to input 1. Signal two

(B) has to be connected to input 2. A ZIC-4AC onboard input relay switches

automatically the correct signal to the outputs 1 and 2. The functionality is

identical for IN-/Output pairs 3 and 4.

Controls and Indicators The Front Panel of the ZIC-4AC contains one reset switch, thirteen LEDs,

and three CAN address switches as shown in Figure 1.

AReset Switch is located on the top of the front panel. Pushing the reset

switch re-initializes the ZIC-4AC operation.

The LEDs follow the reset switch and their functions are defined as follows:

POWER (Green) Normally ON. When illuminated,

indicates that power for the ZIC-4AC is

applied to the card.

CARD FAIL (Yellow) Normally OFF. When illuminated,

indicates that the card microprocessor

has failed.

CAN FAIL (Yellow) Normally OFF. When illuminated,

indicates that the CAN communication

with the ZIC-4AC has terminated and

the card goes into degrade mode

HNET FAIL (Yellow) NOT USED

A24205-A334-B827

P/N 315-035850-2

GND FAULT (Yellow) Normally OFF. When illuminated,

indicates that the ZIC-4AC has

detected either a negative or positive

ground fault on its field wiring.

ZONE 1 (2, 3, 4) ACTIVE (Red) Normally OFF. When illuminated,

indicates that Zone 1 (2, 3, 4) is active.

TROUBLE (Yellow) Normally OFF. When illuminated,

indicates that the ZIC-4AC has

detected a trouble on Zone 1 (open

circuit or short circuit).

Three rotary dial switches at the bottom of the front panel are used to set

the CAN network address of the ZIC-4AC.

PRE-INSTALLATION The following components must be set prior to inserting the card to the CC-5

(refer to Figure 2):

S1: Not used

Switch position has to be off

(upper position)

S2: Not used

All four switch positions have to

be off (left position)

S3: Reset Switch

Momentarily Closed switch that

when pressed will initiate a hard

reset to the ZIC-4AC (similar to a

cold boot).

S5: Input Power Select

This switch selects the source of

voltage input to power the ZIC-

4AC. BP Power indicates that

the input is derived from the

backplane of the CC -2/CC-5 and

EXT Power indicates that the

input is derived from E5/E11

terminal of the CC-2/CC-5,

normally connected to non-

power limited output of the PSC-

12/PSX-12. It is important to take

into account the source of the

voltage during power

calculations.

S4, S6, S7: Network Address Switch

Set the two-digit CAN network address for the ZIC-4AC using the three rotary

dial address switches located near the bottom of the front panel. (Refer to

Figure 1 for the location of the switches.) The address for the ZIC -4AC must

be the same as the address selected for it in the Zeus Programming Tool. To

set the address, turn the pointers on each of the three dials to the numbers

for the selected address. For example, if the address is 23, set the pointer for

the HUNDREDS dial to “0”, set the pointer for the TENS dial to “2”, and set

the pointer for the ONES dial to “3”. The range of allowable addresses is

from 001 to 099 (leading zeros must be used).

Figure 2

ZIC-4AC Switch and Jumper Location

for Strobe usage

A24205-A334-B827

P/N 315-035850-2

P1, P2, P3, P4: Input Supervision active / in-active

These headers select NAC input zone supervision being active or inactive. If

the usage application is set for speaker function, remove the shunt jumpers.

If the usage application is set for strobe place the two shunt jumpers of each

header between pins 1-3 and 4-6.

P1 selects NAC input supervision for Zone 1

P2 selects NAC input supervision for Zone 2

P3 selects NAC input supervision for Zone 3

P4 selects NAC input supervision for Zone 4

P5: Not used

No shunt jumpers set

J3: Not used

No shunt jumpers set

Output Zones The ZIC-4AC can be configured for the following usages:

Speaker zone one or two channel

Strobe, Bell, Horn steady (Unsynchronized) and pulsing (Synchronized)

ZIC-4AC Switch and Jumper Settings

Zone Usage S1 S2 Header Position

Speaker Zone OFF (up) OFF (left) none

NAC OFF (up) OFF (left) 1-3 and 4-6

Programming Options Each ZIC-4AC card is subdivided into four output circuits that can be

programmed independently of each other. In the Zeus Programming Tool,

highlight the selected ZIC-4AC Output Ckt in the Physical View and open the

Detail View -Properties to modify and/or define the following ZIC-4AC

output circuit properties:

CAN Address This address must match the

address set in the ZIC-4AC

hardware. (001 to 099)

Slot Location This defines the location where

the ZIC-4AC is inserted in the

CC-5/CC2.

Base Language Custom Message The message associated with the

ZIC-4AC output circuit.

Alternate Language Custom Message The message associated with the

ZIC-4AC output circuit in an

alternate language.

Disarm at Startup Determines if the ZIC-4AC

Output Ckt is disarmed after

initial power -up.

Degrade Alarm Activation Determines if Degrade Alarm will

activate the ZIC-4AC circuit when

asserted.

A24205-A334-B827

P/N 315-035850-2

Wiring Type Defines if the circuit is Class A or

Class B wiring type.

Silenceable Option Determines if the circuit is

Silenceable or Non-Silenceable.

Some restrictions apply to certain usage selections that are enforced by the

Zeus tool during Edit mode or Compile time.

Refer to the Zeus Quick Start Manual, A24205-A334-A828 (German) or

A24205-A334-B828 (English), or the Zeus self-help index for more information.

Wiring

Disconnect BATTERY and AC prior to working on equipment

All field wiring to the ZIC-4AC is

connected to the terminal blocks of the

CC-5/CC-2 card cage slot in which it is

installed (Refer to Figure 3).

To Connect External Wiring

1. Loosen the screw of the

terminal by turning it

counterclockwise.

2. Insert the wire into the side of

the terminal block.

3. Tighten the screw of the

terminal block by turning it

clockwise.

The top terminals (1 through 8 and 9

through 16) are connected to the

notification appliance devices such as

bells, horns, strobes, speakers, etc. Each

zone has four terminal connections: (+),

Class A (+), (-), Class A (-). These

terminals are power limited.

The bottom terminals (17 through 24) are

connected to the input power source of the NAC devices. Each zone has a (+)

terminal and (-) terminal. These terminals are not power limited.

Care must be taken when installing the zone input and zone output field

wiring to prevent possible cross wiring. This can cause severe damage to

the system when powered up or when zone is activated.

The screw terminals can accommodate one 12 -24 AWG (Ø0.5mm –

2.5mm2) or two 16-24 AWG (Ø0.5mm – 1.5mm2).

If the total output of all 4 zones exceeds 12 amps, a single PSC-12C cannot

be used to supply the ZIC-4AC. Refer to the PSC-12C Installation Instructions

A24205-A334-B798 for information when the total system load exceeds 12 amps.

Figure 3

ZIC-4AC Wiring The 24VDC Power

Lines To The ZIC-AC Slot In The CC-5

A24205-A334-B827

P/N 315-035850-2

INSTALLATION The ZIC-4AC plugs perpendicularly into one slot in the CC-5 card-cage via two

96-pin DIN connectors and can occupy any slot in the card cage. (Refer to

Figure 4.)

Insert the ZIC-4AC card into the card guides right side up (lettering on the

front panel is legible)

Slide the card in until the card edge connectors contact the receptacles on

the motherboard.

Verify that the DIN connectors of the card and the card-cage aligned properly.

The card can only plug in one direction to the card cage, if it does not align,

DO NOT FORCE the card.

Place thumbs on the front panel adjacent to the captive screws and gently

apply even pressure on the card until the connectors seat in the receptacles

on the motherboard.

Secure with the captive screws.

Figure 4

Installing The ZIC-4AC

A24205-A334-B827

P/N 315-035850-2

ELECTRICAL RATINGS

24V Back Plane Current see NOTE below

Screw Terminal 24V Current Total Device Current

6.2V Back Plane Current 0

24V Standby Current Same as 24V Back Plane Current

The 24V backplane current is dependent on the usage and wiring type of

each ZICCkt of the ZIC-4AC. Listed below are the required current draws for

each zone and wiring type.

ZIC-4AC Backplane Current Requirement

Zone Usage Output Current

Requirement

Class A Current

Requirement

Not Used 0 0

Strobe – Sync. 17mA 6mA

Strobe – Unsync. 17mA 6mA

Speaker Zone 34mA 6mA

ZIC-4AC Module Current = 89mA

To calculate the maximum backplane current, the following equation should

be used:

ZIC-4AC Module Current + Zone 1 Usage Req.(See Table above)

+ Class A current (if Class A)

+ Zone 2 Usage Req.(See Table above)

+ Class A current (if Class A)

+ Zone 3 Usage Req.(See Table above)

+ Class A current (if Class A)

+ Zone 4 Usage Req.(See Table above)

+ Class A current (if Class A)

Example 1: If a ZIC-4AC has the following ZICCkt setting:

ZICCkt#1 - Speaker Zone Class A

ZICCkt#2 - Speaker Zone Class A

ZICCkt#3 - Speaker Zone Class A

ZICCkt#4 - Speaker Zone Class A

By applying the equation above, the maximum backplane current requirement

for this card will be determined.

Maximum Backplane Current =

89 + (34 + 6) + (34 + 6) + (34 + 6) + (34 + 6) = 249mA (worst case)

A24205-A334-B827

P/N 315-035850-2

Example 2: If a ZIC-4AC has the following ZICCkt setting:

ZICCkt#1 - Strobe Unsync., Class A

ZICCkt#2 - Strobe Sync., Class A

ZICCkt#3 - Strobe Sync., Class B

ZICCkt#4 - not used

Maximum Backplane Current =

89 + (17 + 6) + (17 + 6) + (17 + 0) + (0 + 0) = 152mA

CONFIGURATIONS The ZIC-4AC zones can be configured for the following usages (Refer to

Figures 5 - 8):

NOTES

1. Wiring for each zone can either be

Class A or Class B.

2. All output circuits are power limited

3. Electrical Ratings:

Output Zone Supervisory:

4mA max @ 24VDC

Output Zone Alarm:

4A max @ 24VDC

4. EOL resistor , 24k ohms ,

1 watt , 5%, (comes with module

package)

EOL-Kit S24135-D55-A1

5. Polarity shown in active state.

6. Maximum line resistance is

dependent upon the maximum

current draw of connected

notification appliances when

activated. The field wiring

resistance cannot exceed the

maximum line resistance specified

for any given NAC current draw.

(See Table)

Current Draw 4.0A 3.5A 3.0A 2.5A 2.0A 1.5A 1.0A 0.5A

Max Line Resistance 0.8

ohms

1.0

ohms

1.2

ohms

1.5

ohms

2.0

ohms

2.7

ohms

4.2

ohms

8.7

ohms

Figure 5

ZIC-4AC Supervised Notification Appliance Wiring

A24205-A334-B827

P/N 315-035850-2

Figure 6

ZIC-4AC Single-Channel Audio Wiring

NOTES

1. Wiring for each zone can either be Class A or Class B.

2. All output circuits are power limited.

3. Electrical Ratings:

Output Zone Supervisory: 4mA max @ 24VDC

Output Zone Active: 400 Watts max / zone

4. EOL resistor, 24k ohms, 1 watt, 5%, (comes with module package) EOL-Kit S24235-D55-A1.

5. Polarity shown in active state.

A24205-A334-B827

P/N 315-035850-2

Figure 7

ZIC-4AC Two-Channel Audio Wiring

NOTES

1. Wiring for each zone can either be Class A or Class B.

2. All output circuits are power limited.

3. Electrical Ratings:

Output Zone Supervisory: 4mA max @ 24VDC

Output Zone Active: 400 Watts max / zone

4. EOL resistor, 24k ohms, 1 watt , 5%, (comes with module package) EOL-Kit S24135-D55-A1.

5. Polarity shown in active state.

6. For two channel speaker application, the channel with higher priority (EVAC) must be connected to inputs 2/4 and the

channel with the lower priority (ALERT) must be connected to inputs 1/3 to ensure proper switching operation of the ZIC-

4AC.

7. Verify that P1 - P4 are in the proper location for speaker application.

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens SIMOTION D410 Manual de usuario

Siemens

Siemens SIMATIC NET CP 343-2 Manual de usuario

Siemens

Siemens TC65 Manual de usuario

Siemens

Siemens simovert masterdrives Manual de usuario

Siemens

Siemens multiranger 200 Guía del usuario

Siemens

Siemens RHFL Manual de usuario

Siemens

Siemens PXC D Series Manual de usuario

Siemens

Siemens S5-155U Guía del usuario

Siemens

Siemens Simatic S5 IP 240 Manual de usuario

Siemens

Siemens SMF6120 Manual de usuario

Siemens

Siemens SIRIUS ACT 3SU18 N Series Manual de usuario

Siemens

Siemens ZAM-180 Manual de usuario

Siemens

Siemens SENTRON 7KM PAC 4DI/2DO Manual de usuario

Siemens

Siemens SINUMERIK 840D sl Guía de inicio rápido

Siemens

Siemens SIMATIC PRO Extension Units KP Series Manual de usuario

Siemens

Siemens NIM-1M Manual de usuario

Siemens

Siemens 7SA513BB Series Instrucciones de funcionamiento e instalación

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens CP-8000 Manual de usuario

Siemens

Siemens MXG461B Series Manual del propietario

Siemens

Siemens SINAMICS G130 Manual de usuario

Siemens

Siemens SIMATIC TDC Guía del usuario

Siemens

Siemens SINUMERIK 840D sl Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Documento técnico

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario