Siemens SINUMERIK 840Di Manual

SINUMERIK 840D/840Di/810D

Operator's Guide

User Documentation

03.2002 Edition

CAD Reader

SINUMERIK 840D/840Di/810D

CAD Reader

03.02 Edition

Operator's Guide

Introduction 1

How to Use the

CAD Reader

Additional Settings 3

Example of Application 4

Appendix A

Index I

Valid for

Control System Software Version

SINUMERIK 840D 6

SINUMERIK 840DE (export version) 6

SINUMERIK 840D (powerline) 6

SINUMERIK 840DE (powerline export version) 6

SINUMERIK 840Di 2

SINUMERIK 840DiE (export version) 2

SINUMERIK 810D 3

SINUMERIK 810DE (export version) 3

SINUMERIK 810D (powerline) 6

SINUMERIK 810DE (powerline export version) 6

SINUMERIK®Documentation

Printing history

Brief details of this edition and previous editions are listed below.

The status of each edition is shown by the code in the "Remarks" column.

Status code in the "Remarks" column:

A .... New documentation.

B .... Unrevised edition with new Order No.

C .... Revised edition with new status.

If factual changes have been made on the page since the last edition, this is indicated by a

new edition coding in the header on that page.

Edition Order No. Comment

03.02 Included only in the online help A

This manual is included in the documentation available on CD ROM (DOCONCD)

Edition Order No. Comment

09.02 6FC5 298-6CA00-0BG3 C

Trademarks

SIMATICâ, SIMATIC HMIâ, SIMATIC NETâ, SIROTECâ, SINUMERIKâand SIMODRIVEâare registered

trademarks of Siemens AG. Other names in this publication might be trademarks whose use by a third party for

his own purposes may violate the rights of the registered holder.

Further information is available at web site:

http://www.ad.siemens.de/sinumerik

This publication was produced with WinWord V8.0

and Designer V7.0 and DocuTool SinuTool.

The reproduction, transmission or use of this document or its contents is not

permitted without express written authority. Offenders will be liable for damages.

All rights, including rights created by patent grant or registration of a utility model

or design, are reserved.

Other functions not described in this documentation might be executable in the

control. This does not, however, represent an obligation to supply such functions

with a new control or when servicing.

We have checked that the contents of this document correspond to the hardware

and software described. Nonetheless, differences might exist and we cannot

therefore guarantee that they are completely identical. The information given in this

publication is reviewed at regular intervals and any corrections that might be

necessary are made in subsequent editions. We welcome suggestions for

improvement.

Subject to change without prior notice.

Order No. Included only in the online help

Printed in Germany

Siemens Aktiengesellschaft

003.02 Contents 0

SINUMERIK 840D/840Di/810D Operator's Guide CAD Reader (CAD) – 03.02 Edition 0-5

Introduction 1-15

1.1 The CAD Reader product ................................................................................................. 1-16

1.2 General function................................................................................................................ 1-16

1.2.1 Scope of application .................................................................................................... 1-17

1.2.2 Software....................................................................................................................... 1-17

1.2.3 Formats ....................................................................................................................... 1-18

1.2.4 Plane generation.......................................................................................................... 1-18

How to Use the CAD Reader 2-19

2.1 General operating procedures .......................................................................................... 2-20

2.2 Define the zero point......................................................................................................... 2-21

2.3 Contour trace .................................................................................................................... 2-21

2.4 Drill points ......................................................................................................................... 2-23

2.5 Manipulate graphic display................................................................................................ 2-23

2.6 Process an imported file ................................................................................................... 2-24

Additional Settings 3-27

3.1 Additional settings and displays........................................................................................ 3-28

Example of Application 4-31

4.1 Example of application for a contour trace ....................................................................... 4-32

Appendix A-35

A References .........................................................................................................................A-35

I.1 Keyword Index ....................................................................................................................A-49

0Contents 03.02 0

0-6 SINUMERIK 840D/840Di/810D Operator's Guide CAD Reader (CAD) – 03.02 Edition

Notes

003.02 Preface

Structure of manual 0

SINUMERIK 840D/840Di/810D Operator's Guide CAD Reader (CAD) – 03.02 Edition 0-7

Preface

Organization of

documentation

SINUMERIK documentation is organized on 2 separate levels:

•General Documentation

•User documentation

Target group This Manual is intended for machine-tool users. This publication

provides detailed information that the user needs to operate this

application for the SINUMERIK 840D/840Di/810D controls.

Hotline If you have any queries, please contact the Hotline given below:

A&D Technical Support Tel.: ++49-180-5050-222

Fax: ++49-180-5050-223

If you have any questions about the documentation (suggestions,

corrections), please send a fax to the following fax address or email:

A&D Technical Support Tel.: ++49-9131-98-2176

Email: motioncontrol.docu@erlf.siemens.de

Fax form: See Suggestions/Corrections Sheet at the back of the

document.

Internet address

http://www.ad.siemens.de/sinumerik

Objectives This Operator's Guide describes the CAD Reader PC application and

how to use it. The CAD Reader enables you to convert drawings

constructed with a CAD system for further processing on a

SINUMERIK control. The format of the imported file is DXF (Drawing

eXchange Format) from which contours or drill points are filtered out.

Note

The CAD Reader can be used for systems with the following software

versions:

Controls SINUMERIK 840D/840Di/810D All versions

Target systems HMI Advanced or HMI Embedded SW 5.1 and higher

ShopMill and ManualTurn SW 5.3 and higher

ShopTurn SW 6.2 and higher

Please note the supplementary conditions regarding the number of

cycles.

0Preface 03.02

Structure of manual 0

0-8 SINUMERIK 840D/840Di/810D Operator's Guide CAD Reader (CAD) – 03.02 Edition

Search tools A table of contents and keyword index are provided to help you access

information quickly.

SINUMERIK 840D

powerline

Improved performance versions

•SINUMERIK 840D powerline and

•SINUMERIK 840DE powerline

are available from 09.2001 onwards.

For a list of available powerline modules, please refer to the

Hardware Description:

References: /PHD/ Configuring Manual SINUMERIK 840D

SINUMERIK 810D

powerline

Improved performance versions

•SINUMERIK 810D powerline and

•SINUMERIK 810DE powerline

are available from 03.2002 onwards.

For a list of available powerline modules, please refer to the

Hardware Description:

References: /PHC/ Configuring Manual SINUMERIK 810D

Standard scope This Operator's Guide describes the functionality afforded by standard

functions. Differences and additions implemented by the machine-tool

manufacturer are documented by the machine-tool manufacturer.

Please consult your local Siemens office for more detailed information

about other SINUMERIK 840D, 840Di and 810D as well as the

publications that apply to all SINUMERIK controls (e.g. Universal

Interface, Measuring Cycles ...).

Other functions not described in this documentation might be

executable in the control. This does not, however, represent an

obligation to supply such functions with a new control or when

servicing.

Applicability Catalog NC 60 is the definitive document as regards the validity of

functions

/BU/ Ordering Information, Catalog NC 60.

003.02 Preface

Structure of manual 0

SINUMERIK 840D/840Di/810D Operator's Guide CAD Reader (CAD) – 03.02 Edition 0-9

Structure of descriptions All functions and operating options have been described according to

the same internal structure as far as this is meaningful and

practicable. The various levels of information have been structured so

that you can find the information you are looking for quickly.

1. Function

This theoretical section is primarily intended as learning material for

the NC beginner. It provides important information that will help you to

understand the principle of operating functions.

You should work through the manual at least once to get an idea of

the scope of the functions and capability of your SINUMERIK control.

2. Operating sequence

This section provides a clear diagrammatic description of the

sequence of key inputs required. If inputs have to be made at

individual stages of the sequence or if you require additional

information, you will find this next to the key illustrations.

3. Further notes

For safety reasons, some of the functions are protected from access

by unauthorized persons. The machine-tool manufacturer can

influence or modify the described functions. Please follow the

instructions of the machine-tool manufacturer.

0Preface 03.02

Structure of manual 0

0-10 SINUMERIK 840D/840Di/810D Operator's Guide CAD Reader (CAD) – 03.02 Edition

Explanation of symbols

Function

Operating sequence

Further notes

Cross-references to other documentation or sections

Danger notes

Additional notes or background information

Ordering data option

Explanation

Description of syntax

Programming examples

Otros manuales para SINUMERIK 840Di

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens SIMATIC ET 200SP HA Manual de usuario

Siemens

Siemens GAMMA instabus Touch control TC5 Manual de usuario

Siemens

Siemens SIPROTEC 7VE61 Manual de usuario

Siemens

Siemens SIMATIC 6ES7135-4MB02-0AB0 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIMOTION Manual de lista de piezas

Siemens

Siemens SCALANCE W788C-2 Manual de usuario

Siemens

Siemens SINUMERIK 840D Guía de configuración

Siemens

Siemens 4AI I 4WIRE HART Manual

Siemens

Siemens OCM-16 Manual de usuario

Siemens

Siemens SIMOCODE pro Manual de usuario

Siemens

Siemens SIMOTION D4x5-2 Manual de usuario

Siemens

Siemens SIMATIC FM 456-2 Instrucciones de montaje

Siemens

Siemens SIRIUS ACT 3SU1401-2EE20-6AA0 Manual de usuario

Siemens

Siemens Siwarex U Guía de aplicación

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SINAMICS DCM 6RN Manual de usuario

Siemens

Siemens TL-30U Manual de usuario

Siemens

Siemens MVS661 N Series Manual de usuario

Siemens

Siemens 3KC ATC3100 Manual de usuario

Siemens

Siemens FN2013-U1 Manual de usuario

Siemens

Siemens HZM Manual de usuario

Siemens

Siemens SINUMERIK 828D Turning Manual del propietario

Siemens

Siemens AC75 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario