Siemens SINAMICS G130 Manual de usuario

Operating Instructions · 03/2013

Line reactors

SINAMICS G130

SINAMICS

 

Line reactors

_________________

SINAMICS

SINAMICS G130

Line reactors

Operating Instructions

Control version V4.6

03/2013

A5E00331462A

Safety information

General

Mechanical installation

Electrical installation

Technical specifications

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E00331462A

Ⓟ 05/2013 Technical data subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Line reactors

Operating Instructions, 03/2013, A5E00331462A 3

Table of contents

1 Safety information...................................................................................................................................... 5

1.1 Warnings........................................................................................................................................5

1.2 Safety and application instructions ................................................................................................6

2 General...................................................................................................................................................... 7

3 Mechanical installation............................................................................................................................... 9

4 Electrical installation ................................................................................................................................ 13

5 Technical specifications........................................................................................................................... 15

Table of contents

Line reactors

4 Operating Instructions, 03/2013, A5E00331462A

Line reactors

Operating Instructions, 03/2013, A5E00331462A 5

Safety information 1

1.1 Warnings

WARNING

Dangerous electrical voltage

Hazardous voltages are present when electrical equipment is in operation.

Severe personal injury or substantial material damage may result if these warnings are not

observed.

Only qualified personnel are permitted to work on or around the equipment.

These personnel must be thoroughly familiar with all the warnings and maintenance

procedures described in these operating instructions.

The successful and safe operation of this device is dependent on correct transport, proper

storage and installation, as well as careful operation and maintenance.

National safety guidelines must be observed.

DANGER

Five safety rules

When carrying out any kind of work on electrical devices, the "five safety rules" according to

EN 50110 must always be observed:

1. Disconnect the system.

2. Protect against reconnection.

3. Make sure that the equipment is de-energized.

4. Ground and short-circuit.

5. Cover or enclose adjacent components that are still live.

Note

Use of copper cables for a UL-approved system

For a UL-approved system use 60/75°C copper conductors only.

Safety information

1.2 Safety and application instructions

Line reactors

6 Operating Instructions, 03/2013, A5E00331462A

1.2 Safety and application instructions

DANGER

Dangerous electrical voltage

This equipment is used in industrial high-voltage installations. During operation, this

equipment contains live, bare parts. For this reason, they could cause severe injury or

significant material damage if the required covers are removed, if they are used or operated

incorrectly, or have not been properly maintained.

When the machines are used in non-industrial areas, the installation location must be

protected against unauthorized access (protective fencing, appropriate signs).

Preconditions

The persons responsible for the safety of the plant must ensure that the following conditions

are met:

● Basic planning work for the system and all work relating to transportation, assembly,

installation, commissioning, maintenance and repairs is carried out by qualified personnel

and checked by responsible, suitably skilled personnel.

● The Operating Instructions and machine documentation are always available.

● The technical specifications regarding the applicable installation, connection,

environmental, and operating conditions are always observed.

● The plant-specific assembly and safety guidelines are observed and personal protection

equipment is used.

● Unqualified personnel are forbidden from using these machines and working near them.

These Operating Instructions are intended for qualified personnel and only contain

information and notes relating to the intended purpose of the machines.

The Operating Instructions and machine documentation are written in different languages as

specified in the delivery contracts.

Note

Support by SIEMENS service centers

We recommend engaging the support and services of your local Siemens service center for

all planning, installation, commissioning and maintenance work.

Line reactors

Operating Instructions, 03/2013, A5E00331462A 7

General 2

Description

Line reactors limit low-frequency line-side harmonics to permissible values.

NOTICE

Maintain ventilation clearances

The 100 mm cooling clearances above and to the side of the components must be

observed.

Note

Cable lengths

The connecting cables to the Power Module must be kept as short as possible.

NOTICE

Use only approved line reactors

When using line reactors that have not been approved by SIEMENS for SINAMICS, the

following can occur:

The Power Modules could be damaged/destroyed.

Line harmonics may interfere with or damage other loads connected to the same line

supply.

CAUTION

Hot surfaces

The surface temperature of the line reactors may exceed 80 °C.

NOTICE

Component cooling

Provisions for component cooling must be made at the installation site. Power loss data is

given in the technical specifications.

General

Line reactors

8 Operating Instructions, 03/2013, A5E00331462A

Assignment of line reactor and Power Module

Table 2- 1 Assignment of line reactor and Power Module

Power Module Unit rating of the Power Module Suitable line reactor

Line voltage 380 – 480 V 3 AC

6SL3310-1GE32-1AAx 110 kW 6SL3000-0CE32-3AA0

6SL3310-1GE32-6AAx 132 kW 6SL3000-0CE32-8AA0

6SL3310-1GE33-1AAx 160 kW 6SL3000-0CE33-3AA0

6SL3310-1GE33-8AAx 200 kW 6SL3000-0CE35-1AA0

6SL3310-1GE35-0AAx 250 kW 6SL3000-0CE35-1AA0

6SL3310-1GE36-1AAx 315 kW 6SL3000-0CE36-3AA0

6SL3310-1GE37-5AAx 400 kW 6SL3000-0CE37-7AA0

6SL3310-1GE38-4AAx 450 kW 6SL3000-0CE38-7AA0

6SL3310-1GE41-0AAx 560 kW 6SL3000-0CE41-0AA0

Line voltage 500 – 600 V 3 AC

6SL3310-1GF31-8AAx 110 kW 6SL3000-0CH32-2AA0

6SL3310-1GF32-2AAx 132 kW 6SL3000-0CH32-2AA0

6SL3310-1GF32-6AAx 160 kW 6SL3000-0CH32-7AA0

6SL3310-1GF33-3AAx 200 kW 6SL3000-0CH33-4AA0

6SL3310-1GF34-1AAx 250 kW 6SL3000-0CH34-8AA0

6SL3310-1GF34-7AAx 315 kW 6SL3000-0CH34-8AA0

6SL3310-1GF35-8AAx 400 kW 6SL3000-0CH36-0AA0

6SL3310-1GF37-4AAx 500 kW 6SL3000-0CH38-4AA0

6SL3310-1GF38-1AAx 560 kW 6SL3000-0CH38-4AA0

Line voltage 660 – 690 V 3 AC

6SL3310-1GH28-5AAx 85 kW 6SL3000-0CH31-1AA0

6SL3310-1GH31-0AAx 90 kW 6SL3000-0CH31-1AA0

6SL3310-1GH31-2AAx 110 kW 6SL3000-0CH31-6AA0

6SL3310-1GH31-5AAx 132 kW 6SL3000-0CH31-6AA0

6SL3310-1GH31-8AAx 160 kW 6SL3000-0CH32-2AA0

6SL3310-1GH32-2AAx 200 kW 6SL3000-0CH32-2AA0

6SL3310-1GH32-6AAx 250 kW 6SL3000-0CH32-7AA0

6SL3310-1GH33-3AAx 315 kW 6SL3000-0CH33-4AA0

6SL3310-1GH34-1AAx 400 kW 6SL3000-0CH34-8AA0

6SL3310-1GH34-7AAx 450 kW 6SL3000-0CH34-8AA0

6SL3310-1GH35-8AAx 560 kW 6SL3000-0CH36-0AA0

6SL3310-1GH37-4AAx 710 kW 6SL3000-0CH38-4AA0

6SL3310-1GH38-1AAx 800 kW 6SL3000-0CH38-4AA0

Otros manuales para SINAMICS G130

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens SIMATIC S7 Manual de usuario

Siemens

Siemens SINUMERIK 828D Turning Manual de usuario

Siemens

Siemens SINAMICS G120 Manual de usuario

Siemens

Siemens TBM-2 Manual de usuario

Siemens

Siemens S7-1500 PROFIBUS Manual de usuario

Siemens

Siemens SINUMERIK 840D Instrucciones de funcionamiento

Siemens

Siemens SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF... Manual de usuario

Siemens

Siemens Siwarex U Guía de aplicación

Siemens

Siemens SINAMICS S120 Manual de lista de piezas

Siemens

Siemens Simatic S7-300 Manual de usuario

Siemens

Siemens 599-02015 Manual del propietario

Siemens

Siemens CZM-1B6 Manual de servicio

Siemens

Siemens SIPROTEC4 7SJ61 Manual de usuario

Siemens

Siemens SIJECT 16i Manual de usuario

Siemens

Siemens SIMATIC S5 1P 243 Documento técnico

Siemens

Siemens LGB21.130A17 Manual de usuario

Siemens

Siemens VGG Series Manual del propietario

Siemens

Siemens VVF Series Manual de usuario

Siemens

Siemens SIMATIC ET 200SP CM 1xDALI Manual del propietario

Siemens

Siemens SIRIUS 3RT1.4 Manual de usuario

Siemens

Siemens LMS14 Manual de usuario

Siemens

Siemens SIMATIC NET Manual de usuario

Siemens

Siemens SINAMICS G120 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP IM 155-6 PN/2 HF Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario