Siemens SIMATIC S7 300 PLC Manual de usuario
Safety Guidelines
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
Danger
indicates that death or severe personal injury will result if proper precautions are not taken.
Warning
indicates that death or severe personal injury may result if proper precautions are not taken.
Caution
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
Caution
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
Notice
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Prescribed Usage
Note the following:
Warning
This device may only be used for the applications described in the catalog or the technical description and only in
connection with devices or components from other manufacturers which have been approved or recommended
by Siemens. Correct, reliable operation of the product requires proper transport, storage, positioning and
assembly as well as careful operation and maintenance.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Automation and Drives
Postfach 48 48
90437 NÜRNBERG
GERMANY
Order No.: A5E00480391-01
Edition 12/2005
Copyright © Siemens AG .
Technical data subject to change
Table of contents
1 Introduction............................................................................................................................................. 1-1
1.1 Introduction ................................................................................................................................ 1-1
2 Preparation............................................................................................................................................. 2-1
2.1 Requirements............................................................................................................................. 2-1
3 Learning units ......................................................................................................................................... 3-1
3.1 1. Step: Wiring............................................................................................................................ 3-1
3.2 2. Step: Configuring CPU 317T-2 DP with HW Config .............................................................. 3-2
3.3 3. Step: Changing the transmission rate at the MPI/DP interface ............................................. 3-4
3.4 4. Step: Vital settings in your DP (DRIVE) configuration ........................................................... 3-5
3.5 5. Step: Generating technology system data............................................................................. 3-6
3.6 6. Step: Configuring the drive in HW Config .............................................................................. 3-7
3.7 7. Step: Configuration of the PG/PC interface......................................................................... 3-10
3.8 8. Step: Downloading the hardware configuration to the target hardware .............................. 3-18
3.9 9. Step: Configuration of the SINAMICS drive with S7T Config .............................................. 3-21
3.10 10. Step: Configuring the axes with S7T Config...................................................................... 3-59
3.11 11. Step: Creating the technology DBs.................................................................................... 3-70
3.12 12. Step: Controlling the axis with the STEP 7 user program ................................................. 3-71
3.13 13. Step: Trial run .................................................................................................................... 3-72
4 Further information ................................................................................................................................. 4-1
4.1 Further information..................................................................................................................... 4-1
CPU 317T-2 DP: Controlling a SINAMICS S120
Getting Started, 12/2005, A5E00480391-01 iii
Table of contents
CPU 317T-2 DP: Controlling a SINAMICS S120
iv Getting Started, 12/2005, A5E00480391-01
Introduction 1
1.1 1.1 Introduction
Introduction
This Getting Started contains a practical example guiding you through thirteen steps in
commissioning a fully functional application, and showing you how to carry out motion
commands. It is thus a valuable help in getting started with the basic functions of a CPU
317T-2 DP.
Depending on your degree of experience, working through the sample will take between two
and three hours.
Note
This Getting Started presumes that you have connected a SINAMICSSINAMICS S120 drive to
the DP (DRIVE) interface of the CPU 317T-2 DP In case you do not have a drive, we
recommend you refer to the Getting started documentation "CPU 317T-2 DP: Controlling a
virtual axis".
CPU 317T-2 DP: Controlling a SINAMICS S120
Getting Started, 12/2005, A5E00480391-01 1-1
Introduction
1.1 Introduction
CPU 317T-2 DP: Controlling a SINAMICS S120
1-2 Getting Started, 12/2005, A5E00480391-01
Preparation 2
2.1 2.1 Requirements
Requirements
The following requirements must be fulfilled:
• An S7-300 station, consisting of:
– Power supply module (PS), for example, 6ES7 307-1EA00-0AA0
– CPU 317T-2 DP with inserted MMC (4 MB or more).
– Optional digital input module (DI) with bus connector, for example,
6ES7 321-1BH02-0AA0
– Optional digital output module (DO) with bus connector, for example,
6ES7 322-1BH01-0AA0
– Two optional front connectors for the digital modules
• A PG with MPI interface and properly installed software packages and commissioning
tools as listed below:
– STEP 7 V5.3 SP3 and higher
– S7-Technology V3.0
• The PG is connected to the CPU via the MPI/DP interface (transmission rate up to 12
Mbps; default 187.5 kbps).
• A SINAMICS® S120 is connected to the CPU 317T-2 DP via the DP (DRIVE) interface.
• The SINAMICS® S120 comprises the following modules:
– CU320 control unit with TB30 terminal board (6SL3040-0MA00-0AA1)
– Smart line module, 5 kW (6SL3130-6AE15-0AA0-Z)
– Single/double motor module, 3 A (6SL3120-2TE13-0AA0-Z)
– 1 synchronous motor 1FK7022-5AK71-1AG3 with incremental encoder sin/cos 1 Vpp
via SMC20 sensor module cabinet (6SL3055-0AA00-5BA1)
– 1 synchronous motor 1FK7022-5AK71-1LG3 with DRIVE-CLiQ interface: Absolute
encoder EnDat 512 pulses/revolution
– Reference loops for position monitoring
– Control box for setpoint/actual-value linkage via terminals
• You know the firmware version of your SINAMICS S120.
CPU 317T-2 DP: Controlling a SINAMICS S120
Getting Started, 12/2005, A5E00480391-01 2-1
Preparation
2.1 Requirements
If you do not know the firmware version, then you can find the version on the supplied
certificate. Alternatively, you can open the "content.txt" file on the CF card. The firmware
version is in the "Internal Version" entry. You can find more detailed information on
reading the firmware version in the SINAMICS S120 product information.
Note
For the example of a drive in Getting Started, we use a SINAMICS® S120 training case.
The training case is available under the following order number:
• Axis version with 1FK7 motor
6ZB2480-0AA00
• Axis version with 1FK7 motors
6ZB2480-0BA00
• The system is completely installed and wired. For information, refer to
Getting Started
CPU 31x: Commissioning
.
• You provided hardware limit switches and EMERGENCY-OFF switches for safe and
reliable operation of the system.
Warning
Operation of an S7-300 as part of plants or systems is subject to special rules and
regulations, based on its field of application. Please note the current safety regulations for
the prevention of accidents, e.g. IEC 204 (EMERGENCY-OFF equipment). You risk
severe injury, or damage to machines and equipment if you ignore these directives.
CPU 317T-2 DP: Controlling a SINAMICS S120
2-2 Getting Started, 12/2005, A5E00480391-01
Preparation
2.1 Requirements
Example configuration
00&
36
67(3
67HFKQRORJ\
&38
',
&8
'5,9(&/,4
352),%86
'3'5,9(
;
;
;
;
;
;
;
;
;
;
60&
'2
6PDUW/LQH
0RGXOH
'RXEOH0RWRU
0RGXOH 0RGXOH
0RWRU
(QFR
GHU
0RWRU
(QFR
GHU
1R'5,9(
&/,4
LQWHUIDFH
6HWWLQJRIVXSSO\YROWDJH
3RZHUVXSSO\212))
0RXQWLQJUDLO
352),%86FDEOHIRU
FRQQHFWLRQWRWKH03,
LQWHUIDFH
3URJUDPPLQJ
GHYLFH3*ZLWK
0RGHVHOHFWRU
,QWHJUDWHGLQSXWVRXWSXWVIRUWHFKQRORJ\
/('V
Task
Configuration of an axis using HW Config and S7T Config. You then operate this axis with
the help of a STEP 7 user program.
CPU 317T-2 DP: Controlling a SINAMICS S120
Getting Started, 12/2005, A5E00480391-01 2-3
Preparation
2.1 Requirements
CPU 317T-2 DP: Controlling a SINAMICS S120
2-4 Getting Started, 12/2005, A5E00480391-01
Otros manuales para SIMATIC S7 300 PLC
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Unidad de control de Siemens
Siemens
Siemens SIRIUS 3RA2712 Documento técnico
Siemens
Siemens 3UF51 Manual de usuario
Siemens
Siemens SINUMERIK 840D sl Manual de usuario
Siemens
Siemens SIMOCODE pro DM-F Local Manual de usuario
Siemens
Siemens SINAMICS S120 Documento técnico
Siemens
Siemens SIRIUS 3RW5 series Documento técnico
Siemens
Siemens LMV 5 Series Manual de usuario
Siemens
Siemens SIMATIC 6DL1131-6DF00-0PK0 Documento técnico
Siemens
Siemens ASIC SIM 1-2 Manual de lista de piezas
Siemens
Siemens FC1008-A Manual
Siemens
Siemens SIRIUS ACT 3ZX1012-0SU14-1KA1 Manual de usuario
Siemens
Siemens SIMATIC ET 200SP Manual de usuario
Siemens
Siemens FT2018-U1 Manual de usuario
Siemens
Siemens SR-35 Manual de usuario
Siemens
Siemens SITRANS PCS 7 Manual de lista de piezas
Siemens
Siemens PROFIBUS CP 1542-5 Manual de usuario
Siemens
Siemens 6ES5-424 Manual del producto
Siemens
Siemens SIPROTEC Manual de usuario
Siemens
Siemens 599-06611 Manual del propietario
Siemens
Siemens ZIC-4A Manual de servicio
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
