Siemens SIMATIC ET 200SP HA Manual de usuario
SIMATIC
ET 200SP HA
Interface Module IM 155-6 PN HA
(6DL1155-6AU00-0PM0)
Manual
05/2017
A5E39262148-AA
Security information 1
Product overview 2
Wiring 3
Parameters 4
Maintenance 5
Displays and interrupts 6
Technical specifications 7
Diagnostic messages A
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E39262148-AA
Ⓟ 05/2017 Subject to change
Copyright © Siemens AG 2017.
All rights reserved
Table of contents
1 Security information......................................................................................................................................5
2Product overview..........................................................................................................................................7
2.1 Properties.................................................................................................................................7
3Wiring.........................................................................................................................................................11
3.1 Pin assignment.......................................................................................................................11
3.2 Schematic circuit diagram......................................................................................................13
4 Parameters.................................................................................................................................................15
4.1 Parameter assignment...........................................................................................................15
5 Maintenance...............................................................................................................................................17
5.1 Exchanging the BusAdapter or interface of the distributed I/O..............................................17
6 Displays and interrupts...............................................................................................................................19
6.1 Status and error displays.......................................................................................................19
6.2 Interrupts................................................................................................................................23
7 Technical specifications..............................................................................................................................25
A Diagnostic messages.................................................................................................................................31
A.1 Diagnostics messages and maintenance events...................................................................31
Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)
Manual, 05/2017, A5E39262148-AA 3
Table of contents
Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)
4Manual, 05/2017, A5E39262148-AA
Security information 1
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines, and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions only form one element of such a concept.
Customer is responsible to prevent unauthorized access to its plants, systems, machines and
networks. Systems, machines and components should only be connected to the enterprise
network or the internet if and to the extent necessary and with appropriate security measures
(e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into
account. For more information about industrial security, please visit:
http://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends to apply product updates as soon as available and to always
use the latest product versions. Use of product versions that are no longer supported, and
failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
http://www.siemens.com/industrialsecurity.
Validity of the documentation
This product manual describes the IM 155-6 PN HA interface module with the article number
6DL1155-6AU00-0PM0.
It supplements the system manual of the
ET 200SP HA Distributed I/O System
.
Functions that generally relate to the system are described in this manual.
The information in this product manual, system manual and function manual enables you to
commission the ET 200SP HA distributed I/O system.
Conventions
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, on the
handling of the product, or on the section of the documentation to which particular attention
should be paid.
Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)
Manual, 05/2017, A5E39262148-AA 5
Security information
Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)
6Manual, 05/2017, A5E39262148-AA
Product overview 2
2.1 Properties
View
①Module type and designation ⑧MAC address (specific address for this exact module)
②LED for operating state ⑨Function status and firmware version
③LED for diagnostics ⑩Article number
④LED for maintenance ⑪Connector for supply voltage
⑤2D matrix code ⑫Slot for PROFINET BusAdapter
⑥LED for master operation ⑬PROFINET BusAdapter
⑦LED for supply voltage ⑭Terminal block for interface module (figure: for redundant
interface modules)
Figure 2-1 View of IM 155‑6 PN HA
Properties
The IM 155‑6 PN HA, together with the carrier and BusAdapter, forms the interface of the
ET 200SP HA.
The interface is used for communication between the CPU and the connected ET 200SP HA
I/O modules via PROFINET IO.
Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)
Manual, 05/2017, A5E39262148-AA 7
The interface has the following technical properties:
● Supply voltage 1L+ 24 V DC (SELV/PELV).
The supply voltage is fed via the carrier module.
The connection plug is included in the scope of delivery of the interface module.
● PROFINET IO connection via BusAdapter (see following paragraph, "Accessories")
The interface supports the following functions:
● Firmware update
● I&M identification data
● Pulling and plugging modules in RUN
● Value status QI
● IO redundancy
● Time stamping
● Multi Hot Swap (pulling/plugging of multiple I/O modules during operation)
● Saving service data
● Recording the value status of I/O modules
● Reference temperature distribution
You can configure the interface with HW Config and integrate it into your system
Note
The IM 155‑6 PN HA cannot be pulled/plugged when the associated connector for the supply
voltage is plugged in.
PROFINET IO functions
The interface supports the following PROFINET IO functions:
● Integrated BusAdapter with 2 ports
● Supported Ethernet services: ping, arp, network diagnostics (SNMP)/MIB-2, LLDP-MIB and
MRP-MIB
● Port diagnostics
● Disabling of ports
● Minimum update time of 250 µs
● Device replacement without programming device (PG)
● Reset to factory settings via PROFINET IO
● System redundancy S2
● System redundancy R1
● Media redundancy (MRP)
● Support of submodules on suitable I/O modules
Product overview
2.1 Properties
Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)
8Manual, 05/2017, A5E39262148-AA
Accessories
The following accessories must be ordered separately:
BusAdapter
● BusAdapter BA 2×RJ45 (6DL1-6AR00-0AA0) - adapter for Ethernet cable with RJ45
connector
● BusAdapter BA 2×FC (6DL1-6AP00-0AA0) - adapter for direct connection of the Fast
Connect bus cable
● BusAdapter BA 2×LC (6DL1-6AG00-0AA0) - adapter for glass fiber optic cable with
IE FC FO connector
Carrier modules
● Carriers for the IM 155‑6 PN HA are available in the following variants:
– Carrier for one IM 155‑6 PN HA
– Carrier for two IM 155‑6 PN HA for redundant configuration
The carriers connect the IM 155‑6 PN HA to the backplane bus. They enable data exchange
with the I/O modules.
Server module and power bus cover
● The server module and power bus cover are included in the product package of the carrier
module and are available separately as accessories.
● The server module and power bus cover terminate the configuration of the ET 200SP HA.
● Place the server module and the power bus cover at the end of the configuration.
The power bus cover serves to protect the power bus contacts.
Marking options
● Labeling strips
● Reference identification label
Product overview
2.1 Properties
Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)
Manual, 05/2017, A5E39262148-AA 9
Product overview
2.1 Properties
Interface Module IM 155-6 PN HA (6DL1155-6AU00-0PM0)
10 Manual, 05/2017, A5E39262148-AA
Otros manuales para SIMATIC ET 200SP HA
18
Tabla de contenidos
Otros manuales de Unidad de control de Siemens
Siemens
Siemens SIMATIC NET 6GK1110-1AA00 Manual de usuario
Siemens
Siemens SIMATIC NET CP 343-2 Manual de usuario
Siemens
Siemens SIMATIC C7 Manual de usuario
Siemens
Siemens SINUMERIK 828D PPU Series Manual de usuario
Siemens
Siemens PLC-4 Manual de usuario
Siemens
Siemens SINUMERIK 840D sl Manual de usuario
Siemens
Siemens Cm-lon 6BK1700-0BA10-0AA00 Manual de usuario
Siemens
Siemens Sinumerik 840DiE sl Manual de usuario
Siemens
Siemens SIRIUS ACT 3ZX1012-0SU14-1KA1 Manual de usuario
Siemens
Siemens SIRIUS 3SB3 Manual de usuario
Siemens
Siemens PSO 4000 Manual de usuario
Siemens
Siemens SIRIUS 3RT1.5 Manual de usuario
Siemens
Siemens OZW771 Manual de usuario
Siemens
Siemens SIMATIC NET CP 343-1 Manual de usuario
Siemens
Siemens 7KM9300-0AE01-0AA0 Manual de usuario
Siemens
Siemens SINAMICS G120 Manual de usuario
Siemens
Siemens SIPROTEC4 7SJ61 Manual de usuario
Siemens
Siemens SENTRON Series Manual de usuario
Siemens
Siemens SENTRON 7KM PAC 4DI/2DO Manual de usuario
Siemens
Siemens SINUMERIK 808D Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
