Siemens Simatic ET 200MP Manual de usuario

___________________

SIMATIC

ET 200MP

Interface module IM 155-5 PN BA

(6ES7155-5AA00-0AA0)

Manual

02/2017

A5E38017683

-AA

Preface

Documentation guide

Product overview

Wiring

Interrupts and diagnostic,

error, and system alarms

Technical specifications

Dimension drawing

Siemens AG

Division Digital Factory

Postfach 48 48

90026 N

ÜRNBERG

GERMANY

A5E38017683-AA

Ⓟ

02/2017 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Interface module IM 155-5 PN BA (6ES7155-5AA00-0AA0)

4Manual, 02/2017, A5E38017683-AA

Preface

Purpose of the documentation

This manual supplements the system manual S7-1500, ET 200MP automation system

(https://support.industry.siemens.com/cs/ww/en/view/59191792). Functions that generally

relate to the system are described in this manual.

The information provided in this manual and in the system/function manuals support you in

commissioning the system.

Conventions

Please also observe notes marked as follows:

Note

A note contains important information on the product, on the handling of the product and on

the section of the documentation to which particular attention should be paid.

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens’ products and solutions only form one element of such a concept.

Customer is responsible to prevent unauthorized access to its plants, systems, machines

and networks. Systems, machines and components should only be connected to the

enterprise network or the internet if and to the extent necessary and with appropriate security

measures (e.g. use of firewalls and network segmentation) in place.

Additionally, Siemens’ guidance on appropriate security measures should be taken into

account. For more information about industrial security, please visit

(http://www.siemens.com/industrialsecurity).

Siemens’ products and solutions undergo continuous development to make them more

secure. Siemens strongly recommends to apply product updates as soon as available and to

always use the latest product versions. Use of product versions that are no longer supported,

and failure to apply latest updates may increase customer’s exposure to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under (http://www.siemens.com/industrialsecurity).

Interface module IM 155-5 PN BA (6ES7155-5AA00-0AA0)

Manual, 02/2017, A5E38017683-AA 5

Table of contents

Preface ................................................................................................................................................... 4

1 Documentation guide .............................................................................................................................. 6

2 Product overview .................................................................................................................................. 10

2.1 Properties................................................................................................................................10

2.2 Functions ................................................................................................................................12

3 Wiring ................................................................................................................................................... 15

3.1 Terminal assignment...............................................................................................................15

3.2 Block diagram .........................................................................................................................16

4 Interrupts and diagnostic, error, and system alarms............................................................................... 17

4.1 Status and error displays ........................................................................................................17

4.2 Interrupts.................................................................................................................................19

4.2.1 Triggering of a diagnostic interrupt .........................................................................................20

4.2.2 Triggering of a hardware interrupt ..........................................................................................20

4.3 Alarms.....................................................................................................................................21

4.3.1 Diagnostic alarms ...................................................................................................................21

4.3.2 Channel diagnostics................................................................................................................22

4.3.3 Invalid configuration states of the ET 200MP on PROFINET IO ............................................23

4.3.4 STOP of the IO controller and recovery of the IO device .......................................................23

5 Technical specifications ........................................................................................................................ 24

A Dimension drawing ............................................................................................................................... 28

Interface module IM 155-5 PN BA (6ES7155-5AA00-0AA0)

6Manual, 02/2017, A5E38017683-AA

Documentation guide

The documentation for the SIMATIC S7-1500 automation system, the CPU 1516pro-2 PN

based on SIMATIC S7-1500 and the SIMATIC ET 200MP distributed I/O system is arranged

into three areas.

This arrangement enables you to access the specific content you require.

Basic information

The System Manual and Getting Started describe in detail the configuration, installation,

wiring and commissioning of the SIMATIC S7-1500 and ET 200MP systems. For

CPU 1516pro-2 PN you use the corresponding operating instructions. The STEP 7 online

help supports you in the configuration and programming.

Device information

Product manuals contain a compact description of the module-specific information, such as

properties, wiring diagrams, characteristics and technical specifications.

Documentation guide

Interface module IM 155-5 PN BA (6ES7155-5AA00-0AA0)

Manual, 02/2017, A5E38017683-AA 7

General information

The function manuals contain detailed descriptions on general topics regarding the SIMATIC

S7-1500 and ET 200MP systems, e.g. diagnostics, communication, motion control, Web

server, OPC UA.

You can download the documentation free of charge from the Internet

(http://w3.siemens.com/mcms/industrial-automation-systems-simatic/en/manual-

overview/Pages/Default.aspx).

Changes and supplements to the manuals are documented in a Product Information.

You can download the product information free of charge from the Internet

(https://support.industry.siemens.com/cs/us/en/view/68052815).

Manual Collection S7-1500/ET 200MP

The Manual Collection contains the complete documentation on the SIMATIC S7-1500

automation system and the ET 200MP distributed I/O system gathered together in one file.

You can find the Manual Collection on the Internet

(https://support.industry.siemens.com/cs/ww/en/view/86140384).

SIMATIC S7-1500 comparison list for programming languages

The comparison list contains an overview of which instructions and functions you can use for

which controller families.

You can find the comparison list on the Internet

(https://support.industry.siemens.com/cs/ww/en/view/86630375).

"mySupport"

With "mySupport", your personal workspace, you make the best out of your Industry Online

Support.

In "mySupport", you can save filters, favorites and tags, request CAx data and compile your

personal library in the Documentation area. In addition, your data is already filled out in

support requests and you can get an overview of your current requests at any time.

You must register once to use the full functionality of "mySupport".

You can find "mySupport" on the Internet (https://support.industry.siemens.com/My/ww/en).

"mySupport" - Documentation

In the Documentation area in "mySupport" you can combine entire manuals or only parts of

these to your own manual.

You can export the manual as PDF file or in a format that can be edited later.

You can find "mySupport" - Documentation on the Internet

(http://support.industry.siemens.com/My/ww/en/documentation).

Documentation guide

Interface module IM 155-5 PN BA (6ES7155-5AA00-0AA0)

8Manual, 02/2017, A5E38017683-AA

"mySupport" - CAx data

In the CAx data area in "mySupport", you can access the current product data for your CAx

or CAe system.

You configure your own download package with a few clicks.

In doing so you can select:

●Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN

macro files

●Manuals, characteristics, operating manuals, certificates

●Product master data

You can find "mySupport" - CAx data on the Internet

(http://support.industry.siemens.com/my/ww/en/CAxOnline).

Application examples

The application examples support you with various tools and examples for solving your

automation tasks. Solutions are shown in interplay with multiple components in the system -

separated from the focus on individual products.

You will find the application examples on the Internet

(https://support.industry.siemens.com/sc/ww/en/sc/2054).

TIA Selection Tool

With the TIA Selection Tool, you can select, configure and order devices for Totally

Integrated Automation (TIA).

This tool is the successor of the SIMATIC Selection Tool and combines the known

configurators for automation technology into one tool.

With the TIA Selection Tool, you can generate a complete order list from your product

selection or product configuration.

You can find the TIA Selection Tool on the Internet

(http://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool).

Documentation guide

Interface module IM 155-5 PN BA (6ES7155-5AA00-0AA0)

Manual, 02/2017, A5E38017683-AA 9

SIMATIC Automation Tool

You can use the SIMATIC Automation Tool to run commissioning and maintenance activities

simultaneously on various SIMATIC S7 stations as a bulk operation independently of the TIA

Portal.

The SIMATIC Automation Tool provides a multitude of functions:

●Scanning of a PROFINET/Ethernet network and identification of all connected CPUs

●Address assignment (IP, subnet, gateway) and station name (PROFINET device) to a

CPU

●Transfer of the date and the programming device/PC time converted to UTC time to the

module

●Program download to CPU

●Operating mode switchover RUN/STOP

●Localization of the CPU by means of LED flashing

●Reading out CPU error information

●Reading the CPU diagnostic buffer

●Reset to factory settings

●Updating the firmware of the CPU and connected modules

You can find the SIMATIC Automation Tool on the Internet

(https://support.industry.siemens.com/cs/ww/en/view/98161300).

PRONETA

With SIEMENS PRONETA (PROFINET network analysis), you analyze the PROFINET

network during commissioning. PRONETA features two core functions:

●The topology overview independently scans PROFINET and all connected components.

●The IO check is a fast test of the wiring and the module configuration of a system.

You can find SIEMENS PRONETA on the Internet

(https://support.industry.siemens.com/cs/ww/en/view/67460624).

Interface module IM 155-5 PN BA (6ES7155-5AA00-0AA0)

10 Manual, 02/2017, A5E38017683-AA

Product overview

2.1

Properties

Article number

6ES7155-5AA00-0AA0

View of the module

Figure 2-1 View of the IM 155-5 PN BA interface module

Properties

●Technical properties

–Connects the ET 200MP distributed I/O system with PROFINET IO

–24V DC power supply (SELV/PELV)

–PROFINET IO connection using RJ45 bus connector

●Supported functions (Page 12)

Otros manuales para simatic ET 200MP

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens WFZ56 Series Manual de instalación y operación

Siemens

Siemens SINUMERIK 840D sl Manual de usuario

Siemens

Siemens DMS8000 MP4 Series Instrucciones de funcionamiento y mantenimiento

Siemens

Siemens 3VL9800-3MJ00 Manual de usuario

Siemens

Siemens 3NP1 Series Manual de usuario

Siemens

Siemens SIMOTION D425 Manual de usuario

Siemens

Siemens RMB795 Manual de usuario

Siemens

Siemens SICAM FCG Manual de usuario

Siemens

Siemens SINUMERIK 840D sl Manual de lista de piezas

Siemens

Siemens VXP45 Series Manual del propietario

Siemens

Siemens LFL Series Manual del propietario

Siemens

Siemens SINUMERIK 840D sl Manual de usuario

Siemens

Siemens AP 641 Manual de servicio

Siemens

Siemens SINAMICS CONNECT 500 Manual de usuario

Siemens

Siemens SCALANCE S615 Manual de usuario

Siemens

Siemens SIMATIC ET 200AL Manual de usuario

Siemens

Siemens SIMATIC 505 Instrucciones de funcionamiento

Siemens

Siemens SINUMERIK 840Di sl Guía de inicio rápido

Siemens

Siemens SIPROTEC PROFINET IO Manual de usuario

Siemens

Siemens GAMMA instabus Touch control TC5 Manual de usuario

Siemens

Siemens SICAM A8000 Series Manual de usuario

Siemens

Siemens SIMOTION Manual de lista de piezas

Siemens

Siemens TMM-1 Manual de usuario

Siemens

Siemens SIRIUS 3RA2712 Documento técnico

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario

Siemens simatic ET 200MP Manual de usuario

Manuales populares de Unidad de control de otras marcas