Siemens HTRI-M Manual de usuario

SiemensSiemens

Siemens IndustryIndustry

IndustryIndustry

Industry,,

,Inc.Inc.

Inc.Inc.

Inc.

BuildingBuilding

Building TT

Tecec

ecec

echnologies Dihnologies Di

hnologies Dihnologies Di

hnologies Divisionvision

visionvision

vision

P/N 315-049480-4

Figure 1

HTRI-M Module

The Model HTRI-M Series Addressable Interface

Module from Siemens Industry, Inc. interfaces

direct shorting devices to the DLC loop circuit of

the FireFinder-XLS System or the FS-DLC loop of

the FS-250 System. It is also approved for 1076,

Proprietary Burglary.

The HTRI-M can monitor a normally open or closed

dry contact and it can report the status of the contact.

PROGRAMMING Refer to Figure 1 to locate the red and black DLC/FS-DLC loop circuit wires of the HTRI-M.

Connect the Addressable Loop Driver circuit wires of the HTRI-M to the Model DPU

Programmer/Tester. Use the cable provided with the Programmer/Tester and the 2

alligator clip to banana plug adapters provided.

To Prevent DamageToThe DPU:

DO NOT connect a HTRI-M to the DPU until all field wiring is removed from the

red and black DLC/FS-DLC loop circuit wires of the HTRI-M.

Connection from the DPU to the HTRI-M is not polarity sensitive. Refer to Figure

3 for the proper connections to the control panel.

(Refer to Figure 2.) Follow the instructions in the DPU Programmer/Tester Manual

(P/N 315-033260) to program the desired address into HTRI-M.

Record the device address on the label located on the HTRI-M.The HTRI-M can now

be installed and wired to the system.

ORG BLK

LINE

2LINE

GRNORG RED

ALL CONNECTIONS ARE POWER LIMITED

EARTH

GND

HTRI-M

Addressable Interface Module

Installation Instructions

Model HTRI-M

NOTES:

1. There can be any number of normally closed or normally open switches.

2. The end of line resistor must be located at the last switch.

3. Do not wire a normally closed switch across the end of line resistor.

4. Only for use with security and status applications.

5. Do not use N.O. switches for security applications.

Figure 2

Wiring Switches

NORMALLY OPEN SWITCHES

(SEE NOTES 2, 3 AND 5)

PROGRAMMABLENORMALLY CLOSED SWITCHES

(SEE NOTE 4)

PROGRAMMABLE

ENDOFLINE

RESISTOR

470 OHMS,

1/4W

ENDOFLINE

RESISTOR

470 OHMS,

1/4W

WIRING (Refer to Figure 3.) Refer to the wiring diagram and wire the addressable interface

module accordingly.

Recommended wire size: 18 AWG minimum

14 AWG maximum

NOTES:

1. All supervised switches must be held closed and/or open for at least a quarter of a second to guarantee detection.

2. End of line device: 470 ohm, 1/4W resistor, P/N 140-820164. For Canadian applications, use Model EL-33 with 470 ohm, 1/4W resistor.

3. HTRI-M is polarity insensitive. Line 1 and Line 2 can be either line of the loop.

4. The supervised switches have the following ratings:

Voltage maximum: 27 VDC

Current maximum: 6mA during polling

Contact resistance maximum: 10 ohms

Maximum cable length: 200 feet (18 AWG) CLine to line: 0.02uF CLine to shield: 0.04uF

Max line size: 14 AWG Min line size: 18 AWG

Ground shield ONLY at the specified location on the Control Panel.

EOL device must be a 470 ohm, 1/4 W resistor.

When replacing an existing HTRI on a device loop,

you must also replace the EOL resistor if it is not

470 ohms, 1/4W.

5. The green wire must be connected to earth ground.

a. Use wire nuts to pass the shield wire through the electrical box with NO connection to the device green wire.

b. Use shielded wire to connect the switch wiring.

c. Tie the switch wiring shield to earth ground.

6. For proprietary burglary application:

a. Use a TSW-1/2 tamper switch to monitor the main enclosure.

b. Monitor each HTRI-M related to this application continuously by using a listed motion detector (to prevent tampering).

7. In supervisory: HTRI-M draws 1.3mA

8. All circuits are power limited.

9. Positive and negative ground fault detected at <25K ohms for orange terminals.

MOUNTING The Model HTRI-M mounts directly into a single gang switchbox

(user supplied)

Connect the appropriate wires using wire

nuts.Tuck the HTRI-M module inside the

electrical box and dress the wiring as re-

quired. (See Figure 4.)

BLACK

GREEN

ORANGE

LINE 2

LINE 1

HTRI-M

RED

TO NEXT

ADDRESSABLE DEVICE

GROUND

(SEE NOTE 5)

470 OHM, ¼W

END OF LINE DEVICE

(SEE NOTE 2)

SUPERVISED SWITCH

(SEE NOTES 1 AND 2)

FROM FIREFINDER-XLS / FS-250

CONTROL PANEL ADDRESSABLE

LOOP DRIVER CIRCUIT OR FROM

PREVIOUS ADDRESSABLE DEVICE

Figure 4

Mounting the HTRI-M

SINGLEGANG

SWITCHBOX

(USER SUPPLIED)

DO NOT

USE REAR

CONDUIT

ENTRY

BLANK SINGLEGANG

SWITCHPLATE

(USER SUPPLIED)

ORG BLKGRNORG RED

ALLCONNECTIONS ARE POWER LIMITED

EARTH

GND LINE

LINE

HTRI-M

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

P/N 315-049480-4

ELECTRICAL RATINGS

pooLCLD-SF/CLD

tnerruC.xaMAm3.1

Figure 3

Installing the HTRI-M Wiring

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens Cm-lon 6BK1700-0BA10-0AA00 Manual de usuario

Siemens

Siemens SIPLUS CMS4000 IFN VIB-A Manual de usuario

Siemens

Siemens LFE1 Series Manual de usuario

Siemens

Siemens WFZ56 Series Manual de instalación y operación

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens RAB10 Series Manual de usuario

Siemens

Siemens SINUMERIK 840D sl Hoja de instrucciones

Siemens

Siemens SIPROTEC 4 7XT71 Series Manual de usuario

Siemens

Siemens AE-30U Manual de usuario

Siemens

Siemens FT2001-A1 Manual de usuario

Siemens

Siemens SR-35 Manual de usuario

Siemens

Siemens SINAMICS G130 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens 3AK Manual de usuario

Siemens

Siemens SITRANS RD500 Manual de usuario

Siemens

Siemens LAL Series Manual de usuario

Siemens

Siemens ZN-31U Manual de usuario

Siemens

Siemens SM 338 Manual de usuario

Siemens

Siemens SIMOTION D4x5 Series Manual de usuario

Siemens

Siemens SIMATIC 6ES7135-4MB02-0AB0 Manual de usuario

Siemens

Siemens SINUMERIK 840D sl Guía de inicio rápido

Siemens

Siemens SINAMICS V60 Manual de usuario

Siemens

Siemens SINUMERIK 805 Manual de usuario

Siemens

Siemens SIWAREX MS Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario