Siemens SCALANCE W788C-2 Manual de usuario

___________________

SIMATIC NET

Industrial Wireless LAN

SCALANCE W788C-2

Operating Instructions

01/2017

A5E03692120

-11

Introduction

Security recommendations

Description

Mounting

Connection

Technical data

Dimension drawings

Approvals

Siemens AG

Division Process Industries and Drives

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E03692120-11

Ⓟ

01/2017 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

SCALANCE W788C-2

Operating Instructions, 01/2017, A5E03692120-11 3

Table of contents

1 Introduction............................................................................................................................................. 5

1.1 Information on the Operating Instructions ................................................................................5

2 Security recommendations...................................................................................................................... 7

3 Description............................................................................................................................................ 11

3.1 Description of the device ........................................................................................................11

3.2 Structure of the type designations ..........................................................................................13

3.3 Components of the product ....................................................................................................14

3.4 Accessories.............................................................................................................................15

3.4.1 Installation...............................................................................................................................15

3.4.2 Flexible connecting cables and antennas...............................................................................18

3.4.2.1 Flexible connecting cables......................................................................................................18

3.4.2.2 Antennas .................................................................................................................................19

3.5 LED display.............................................................................................................................22

4 Mounting............................................................................................................................................... 23

4.1 Securing the housing ..............................................................................................................24

4.2 Wall mounting .........................................................................................................................25

4.3 Installing on the S7-300 standard rail .....................................................................................26

4.4 Installing on a DIN rail.............................................................................................................27

5 Connection ........................................................................................................................................... 29

5.1 Safety when connecting up.....................................................................................................29

5.2 Lightning protection, power supply and grounding .................................................................30

5.3 Power supply and Ethernet.....................................................................................................33

5.4 Antenna connectors ................................................................................................................35

6 Technical data ...................................................................................................................................... 39

6.1 Technical specifications of the SCALANCE W788C-2)..........................................................39

7 Dimension drawings.............................................................................................................................. 43

8 Approvals.............................................................................................................................................. 45

Index..................................................................................................................................................... 47

Table of contents

SCALANCE W788C-2

4Operating Instructions, 01/2017, A5E03692120-11

SCALANCE W788C-2

Operating Instructions, 01/2017, A5E03692120-11 5

Introduction

1.1

Information on the Operating Instructions

Validity of the Operating Instructions

These operating instructions cover the following products:

Product

Article number

SCALANCE W788C-2 RJ-45

6GK5 788-2FC00-1AA0

SCALANCE W788C-2 M12

6GK5 788-2GD00-1AA0

SCALANCE W788C-2 M12 EEC 6GK5788-2GD00-1TA0

If information relates to all the named products, the term SCALANCE W7x8 will be used.

These operating instructions apply to the following software version:

●SCALANCE W7x8C with firmware as of version 8.31

Purpose of the Operating Instructions

Using the Operating Instructions, you will be able to install and connect the SCALANCE

W7x8 correctly. The configuration and the integration of the device in a WLAN are not

described in these instructions.

Documentation on the accompanying CD

You will find introductory information about configuration in the document "Getting Started

SCALANCE WLC711" on the accompanying SIMATIC NET IWLAN CD under the file name:

GS_SCALANCE-WLC711_76 pdf

Note

Detection of the W788C-2 M12 EEC devices

When the W788C

-2 M12 EEC devices are detected by the configuration software of the

WLC 711, they are shown as W788C

-2 M12.

Note

Make sure that you read the explanations and instructions in the README.txt file

Introduction

1.1 Information on the Operating Instructions

SCALANCE W788C-2

6Operating Instructions, 01/2017, A5E03692120-11

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens’ products and solutions only form one element of such a concept.

Customer is responsible to prevent unauthorized access to its plants, systems, machines

and networks. Systems, machines and components should only be connected to the

enterprise network or the internet if and to the extent necessary and with appropriate security

measures (e.g. use of firewalls and network segmentation) in place.

Additionally, Siemens’ guidance on appropriate security measures should be taken into

account. For more information about industrial security, please visit

http://www.siemens.com/industrialsecurity (http://www.siemens.com/industrialsecurity)

Siemens’ products and solutions undergo continuous development to make them more

secure. Siemens strongly recommends to apply product updates as soon as available and to

always use the latest product versions. Use of product versions that are no longer supported,

and failure to apply latest updates may increase customer’s exposure to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under

http://www.siemens.com/industrialsecurity (http://www.siemens.com/industrialsecurity)

Trademarks

The following and possibly other names not identified by the registered trademark sign ®are

registered trademarks of Siemens AG:

SIMATIC NET, SCALANCE, C-PLUG, RCOAX

SCALANCE W788C-2

Operating Instructions, 01/2017, A5E03692120-11 7

Security recommendations

To prevent unauthorized access, note the following security recommendations.

General

●You should make regular checks to make sure that the device meets these

recommendations and/or other security guidelines.

●Evaluate your plant as a whole in terms of security. Use a cell protection concept with

suitable products.

●When the internal and external network are disconnected, an attacker cannot access

internal data from the outside. Therefore operate the device only within a protected

network area.

●For communication via non-secure networks use additional devices with VPN functionality

to encrypt and authenticate the communication.

●Terminate management connections correctly (WBM. Telnet, SSH etc.).

Physical access

●Restrict physical access to the device to qualified personnel.

●The memory card or the PLUG (C-PLUG, KEY-PLUG, security PLUG) contains sensitive

data such as certificates, keys etc. that can be read out and modified.

Software (security functions)

●Keep the software up to date. Check regularly for security updates of the product.

You will find information on this on the Internet pages "Industrial Security

(http://www.siemens.com/industrialsecurity)".

●Inform yourself regularly about security advisories and bulletins published by Siemens

ProductCERT (http://www.siemens.com/cert/en/cert-security-advisories.htm).

●Only activate protocols that you really require to use the device.

●Use the security functions such as address translation with NAT (Network Address

Translation) or NAPT (Network Address Port Translation) to protect receiving ports from

access by third parties.

●Restrict access to the device with a firewall or rules in an access control list (ACL -

Access Control List).

●If RADIUS authentication is via remote access, make sure that the communication is

within the secured network area or is via a secure channel.

●The option of VLAN structuring provides good protection against DoS attacks and

unauthorized access. Check whether this is practical or useful in your environment.

Security recommendations

SCALANCE W788C-2

8Operating Instructions, 01/2017, A5E03692120-11

●Enable logging functions. Use the central logging function to log changes and access

attempts centrally. Check the logging information regularly.

●Configure a Syslog server to forward all logs to a central location.

●Use WPA2/ WPA2-PSK with AES to protect the WLAN. If iPCF or iPCF-MC is used, use

the AES encryption.

Passwords

●Define rules for the use of devices and assignment of passwords.

●Regularly update passwords and keys to increase security.

●Change all default passwords for users before you operate the device.

●Only use passwords with a high password strength. Avoid weak passwords for example

password1, 123456789, abcdefgh.

●Make sure that all passwords are protected and inaccessible to unauthorized personnel.

●Do not use the same password for different users and systems or after it has expired.

Keys and certificates

This section deals with the security keys and certificates you require to set up HTTPS (

HyperText Transfer Protocol Secured Socket Layer).

●We strongly recommend that you create your own HTTPS certificates and make them

available.

There are preset certificates and keys on the device. The preset and automatically

created HTTPS certificates are self-signed.

We recommend that you use HTTPS certificates signed either by a reliable external or by

an internal certification authority. The HTTPS certificate checks the identity of the device

and controls the encrypted data exchange. You can install the HTTPS certificate via the

WBM (System > Load and Save).

●Handle user-defined private keys with great caution if you use user-defined SSH or SSL

keys.

●Use the certification authority including key revocation and management to sign the

certificates.

●Verify certificates and fingerprints on the server and client to avoid "man in the middle"

attacks.

●We recommend that you use certificates with a key length of 2048 bits.

●Change keys and certificates immediately, if there is a suspicion of compromise.

Secure/non-secure protocols

●For the DCP function, enable the "DCP read-only" mode after commissioning.

●Avoid and disable non-secure protocols, for example Telnet and TFTP. For historical

reasons, these protocols are still available, however not intended for secure applications.

Use non-secure protocols on the device with caution.

Security recommendations

SCALANCE W788C-2

Operating Instructions, 01/2017, A5E03692120-11 9

●The following protocols provide secure alternatives:

–SNMPv1/v2 →SNMPv3

Check whether use of SNMPv1 is necessary. SNMPv1 is classified as non-secure.

Use the option of preventing write access. The product provides you with suitable

setting options.

If SNMP is enabled, change the community names. If no unrestricted access is

necessary, restrict access with SNMP.

Use SNMPv3 in conjunction with passwords.

–HTTP →HTTPS

–Telnet →SSH

–SNTP →NTP

●Use secure protocols when access to the device is not prevented by physical protection

measures.

●To prevent unauthorized access to the device or network, take suitable protective

measures against non-secure protocols.

●If you require non-secure protocols and services, operate the device only within a

protected network area.

●Restrict the services and protocols available to the outside to a minimum.

Security recommendations

SCALANCE W788C-2

10 Operating Instructions, 01/2017, A5E03692120-11

Available protocols per port

The following list provides you with an overview of the open ports on this device.

The table includes the following columns:

●

Protocol

All protocols that the device supports

●

Port number

Port number assigned to the protocol

●

Port status

–Open

The port is always open and cannot be closed.

–Open (when configured)

The port is open if it has been configured.

●

Factory setting

–Open

The factory setting of the port is "Open".

–Closed

The factory setting of the port is "Closed".

●

Authentication

Specifies whether or not the protocol is authenticated.

Protocol

Port number

Port status

Factory setting

of the port

Authentication

SSH

TCP/22

Open (when configured)

Open

Yes

TELNET

TCP/23 Open (when configured) Open Yes

HTTP

TCP/80

Open (when configured)

Open

Yes

HTTPS

TCP/443 Open (when configured) Open Yes

SNTP

NTP

UDP/123 Open (when configured) Closed No

SNMP

UDP/161

Open (when configured)

Open

Yes

PROFINET

UDP/34964,

UDP/49154,

49155

Open Open No

Syslog

UDP/514

Open (when configured)

Open

EtherNet/IP

TCP/44818,

UDP/2222,4481

Open (when configured) Open No

DHCP

UDP/67,68

Open (when configured)

Closed

RADIUS

UDP/1812,1813

Open (when configured)

Closed

TFTP

UDP/69

Open (when configured)

Closed

Otros manuales para SCALANCE W788C-2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens Siwarex U Guía de aplicación

Siemens

Siemens SIRIUS 3RA2711-DB0 Series Manual de usuario

Siemens

Siemens Add 7 AddFEM Manual de usuario

Siemens

Siemens VAI60.15-15 Manual de usuario

Siemens

Siemens RUGGEDCOM ROS Manual de usuario

Siemens

Siemens Desigo PXC4.E16 Manual de usuario

Siemens

Siemens SIMATIC ET 200AL Manual de usuario

Siemens

Siemens VAI61 Series Manual de usuario

Siemens

Siemens SINUMERIK Series Manual de lista de piezas

Siemens

Siemens SINUMERIK 828D Turning Manual del propietario

Siemens

Siemens MXG461B Series Manual del propietario

Siemens

Siemens SINAMICS S120 Guía de inicio rápido

Siemens

Siemens ECOFAST 3RK1911-4AA Series Manual de usuario

Siemens

Siemens SOAM Manual de usuario

Siemens

Siemens SIMATIC ET 200SP IM 155-6 PN/2 HF Manual de usuario

Siemens

Siemens 3RK2 Series Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens LEC1 Series Manual de usuario

Siemens

Siemens Synco 700 RMB795 Manual de usuario

Siemens

Siemens SICAM A8000 Series Manual de usuario

Siemens

Siemens REMBOX2-MP Manual de usuario

Siemens

Siemens SIPROTEC 7SJ80 Manual de usuario

Siemens

Siemens VAI60.15-15 Manual de usuario

Siemens

Siemens Simatic RTU3030C Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario