Siemens OCM-16 Manual de usuario

Siemens Building Technologies

Fire Safety

P/N 315-033150-3

Model OCM-16

Output Control Module

Installation Instructions

INTRODUCTION The SIEMENS Model OCM-16 Output Control Module

is a re otely located, general purpose output odule. It

provides sixteen open collector outputs to drive LEDs,

incandescent la ps, or external relays. There is an

additional output for a local audible and two inputs for

o entary la p test and local audible silence switches.

OPERATION The OCM-16 is ounted in an enclosure that is re-

otely located fro the Main Panel. Co unication

between the OCM and the NIC-C is through the Control

Area Network (CAN) bus. Each OCM-16 has two 10

position rotary switches that are used to set the board

address on the CAN which is a sub-address of the

NIC-C. The 16 outputs of the OCM-16 are controlled by

essages received fro the NIC-C over the CAN.

A CAN essage can activate any or all of the 16 outputs

to drive LEDs, incandescent 24 Volt la ps or relays.

Whenever any of the outputs is activated, (LEDs, la ps

or relays ON) the local audible (if installed) will sound

until it is acknowledged by shorting position 19 and 20

on TB2. If the outputs are deactivated before the alar

(local audible) is acknowledged, the alar (local

audible) will cease to sound.

By shorting ter inals 17 and 18, all LEDs or la ps will

turn on to confir that they are working and auto ati-

cally will return to their nor al state after a few sec-

onds. Both the la p test and local audible silence

switch on ultiple OCM-16s can be connected to a

single switch, one for each function. A single audible

can also be used with ultiple OCM-16s.

Figure 1

OCM-16 Output Control

Module

12345678

910111213141516

17 18 19 20 21 22 23 24

TB2

TB1

P2 P3

TB3

OCM-16

Siemens Building Technologies

Fire Safety

P/N 315-0033150-32

PRE-INSTALLATION Rotary Address Switches - Set the board address for each OCM-16 using both of

the ten-position rotary switches located on the board (See Figure 2). Each of these

addresses ust be a sub-address of the NIC-C and ust be the sa e as the ad-

dresses assigned in the Zeus Progra ing Tool.

S1/S2 LED, Incandescent/Relay Select Switches

 When LEDs are used, open corresponding dipswitches on S1 and S2 (Refer

to OCM-16 Switches Table) to provide a current li iting resistor of 2.7K

oh s to each LED.

 When incandescent la ps or relays are used, close corresponding

dipswitches on S1 and S2 (Refer to OCM-16 Switches Table) to bypass the

li iting resistors.

SEHCTIWS61-MCO

1BT 1S

hctiwS 1BT 2S

hctiwS

11-1S9 1-2S

22-1S012-2S

33-1S113-2S

44-1S214-2S

55-1S315-2S

66-1S416-2S

77-1S517-2S

88-1S618-2S

INSTALLATION An OCM-16 ay be installed in a REMBOX. When using REMBOX 2 or 4, ount the

OCM-16 in one odule space on a REMBOX2-MP, P/N 500-634211 or REMBOX4-MP,

P/N 500-634212 using the four screws provided. (Refer to REMBOX2-MP/REMBOX4-

MP Installation Instructions, P/N 315-034211.) Up to 4 OCM-16s will fit in a

REMBOX2; up to 8 OCM-16s will fit in a REMBOX4.

WIRING

Disconnect BATTERY and AC prior to working on equipment.

 Each OCM-16 odule is a node in the CAN bus.

 The OCM-16 can be installed with or without an RNI. Connect 24V and

CAN bus as shown in Figures 2 and 3.

 Up to 99 CAN odules, in any co bination, can be connected to the CAN

bus of each NIC-C.

 Each OCM-16 odule is shipped with one CCS cable.

 Cable connections for OCM-16 odules are shown in the following table:

Siemens Building Technologies

Fire Safety

P/N 315-033150-33

SNOITCENNOCELBAC61-MCO

elbaCnoitpircse rebmuNtraPnoitcennoC

LCCgnoL-ELBAC-NAC

rotcudnoc-6,.ni03

412436-995.61-MCOtrifotINRno4PtcennoC

/MCFot61-MCOmorftcennocolA

.)roodno(eludomBSC/MCS/MCL

SCCtrohS-ELBAC-NAC

rotcudnoc-6,.ni½5

935331-55561-MCOoteludom61-MCOtcennoC

worelgnianieludom61-MISro

The CAN bus requires a 1 0S resistance at each end of the loop. Refer to the NIC-C

Installation Instructions, P/N 315-033 40 for details about CAN termination.

Figure 2

OCM-16 Wiring Without An RNI

ROTARY

ADDRESS SWITCHES

12345678

910111213141516

17 18 19 20 21 22 23 24

ON ON

OCM-16

TO PSC-12/PSX-12, TB3

OR ANY REGULATED

POWER LIMITED POWER

SUPPLY LISTED FOR

FIRE PROTECTIVE

SIGNALING USE

TO NEXT

OCM-16

TO PSC-12, TB1

SEE NIC-C

INSTALLATION

INSTRUCTIONS,

P/N 315-033240

FOR WIRING DETAILS

LAMP TEST*

AUDIBLE

DEVICE**

*NORMALLY OPEN MOMENTARY PUSHBUTTON (UL 864 LISTED)

**24VDC AUDIBLE 50mA MAX. (UL 864 LISTED)

(UNSUPERVISED)

–

ACK ALARM*

CAN +

CAN –

SHIELD

+24 V

24 V RET

USE UP TO 16 LED / INCANDESCENT

IN ANY COMBINATION (UNSUPERVISED)

/ RELAY

CORRESPONDING

DIPSWITCH ON

S1/S2

MUST BE SET TO

OFF FOR LEDs.

24VDC

RELAY

COIL

TB3

12345678

910111213141516

17 18 19 20 21 22 23 24

ON ON

OCM-16

CAN +

CAN –

SHIELD

+24 V

24 V RET

USE UP TO 16 LED / INCANDESCENT

IN ANY COMBINATION

/ RELAY

(UNSUPERVISED)

24VDC

RELAY

COIL

TB3

TB1 TB1

P3 P3

INSERT CAN TERMINATOR

P/N 110-134215

INTOP2orP3

IF THIS IS THE LAST

MODULE ON THE PANEL.

DO NOT USEDO NOT USE

SUPERVISED

S4 S3 S4 S3

TB2 TB2

N TES

1. All wiring must be in

accordance with Article 760

of NEC or local building

codes.

2. All circuits are power limited

to NFPA 70 per NEC 760.

3. Electrical Ratings:

Standby current: 14mA max.

@ 24VDC

Active current: 200mA max.

@ 24VDC

4. For additonal information,

refer to the NIC-C Installa-

tion Instructions, P/N 315-

033240.

5. All wiring to TB1 must be:

- within the same room

- within 20 feet

- in rigid conduit

6. Lamp test switch, ACK alarm

switch, and audible device

must be UL 864 listed

devices.

7. CAN network max. line

resistance 16S.

8. Mount the Lamp Test, Ack

Alarm and Audible Device on

the REMB X2/4 front door.

9. Wiring for TB1 and TB2 is 18

AWG min., 12 AWG max.

10. Wiring for TB3 is 26 AWG

min., 16 AWG max.

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, ntario L6T 5E4 CN

P/N 315-033150-3

tnerruCenalPkcaBV420

tnerruCV42lanimreTwercSDELevitcarepAm01+Am41

tnerruCenalPkcaBV2.60

tnerruCybdnatSV42DELevitcarepAm01+Am41

Figure 3

OCM-16 CAN Bus Connections With An RNI

12345678 12345678 12345678 12345678

9 10 11 12 13 14 15 16 9 10 11 12 13 14 15 16 9 10 11 12 13 14 15 16 9 10 11 12 13 14 15 16

17 18 19 20 21 22 23 24 17 18 19 20 21 22 23 24 17 18 19 20 21 22 23 24 17 18 19 20 21 22 23 24

OCM-16 OCM-16 OCM-16 OCM-16

TO RNI, P4

CAN TERMINATOR,

P/N 110-134215

(SHIPPED WITH NIC-C)

CABLE

MODEL

# CCS

CABLE

MODEL

# CCL

Siemens Gebäudesicherheit

GmbH & Co. oHG

D-80930 München

For CE applications in Cerberus E100 syste s refer to

Installation Instruction A24205-A334-B844 (English) or A24205-A334-A844 (Ger an).

ELECTRICAL RATINGS

Otros manuales de Unidad de control de Siemens

Siemens

Siemens SINUMERIK 840D Instrucciones de funcionamiento

Siemens

Siemens SIRIUS 3RW5 series Documento técnico

Siemens

Siemens VXP45 Series Manual del propietario

Siemens

Siemens HCP Manual de usuario

Siemens

Siemens SIMATIC IM 153-2 Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SIRIUS 3RW5 series Documento técnico

Siemens

Siemens MLC Manual de usuario

Siemens

Siemens SIMOTION Manual de lista de piezas

Siemens

Siemens FS-TRI-M Manual de usuario

Siemens

Siemens SIRIUS 3RT1.4 Manual de usuario

Siemens

Siemens SINAMICS SM120 Manual de usuario

Siemens

Siemens SIPROTEC4 7SJ61 Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens LGI16 Series Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SINUMERIK 808D Guía de inicio rápido

Siemens

Siemens simatic ET 200MP Manual de usuario

Siemens

Siemens CZM-1B6 Manual de servicio

Siemens

Siemens FCI2011-U1 Guía

Siemens

Siemens LMU54 Series Manual del operador

Siemens

Siemens ALD-2I Manual de usuario

Siemens

Siemens SIMATIC IM 151/CPU Manual de usuario

Siemens

Siemens SINUMERIK 840D sl Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario