Shure A310-FM Manual de usuario

1/9

A310-FM -- Installation Guide

Permanent Table Installation

The tube and wing nut required to install the rack tray are included with the MXA310 microphone. Refer to the

MXA310 user guide for replacement part information.

Tip: This process assumes that both ends of the network cable are accessible. If the other end of the network ca

ble is not accessible, before installing the tube and plugging in the microphone (step 2), you must guide the cable

through the hardware components in the following order:

1. Wing nut (see image for correct orientation)

2. Bracket (under table)

3. Table

4. Tray (above table)

Shure Incorporated

2/9

Installation Process

1. Remove the 3 screws located in the center on the bottom of the microphone

Shure Incorporated

3/9

2. Plug a network cable into the microphone and guide it through the center exit path. When the cable is secured,

guide it through the tube.

Note: If necessary, remove the retaining tabs to install thicker cable. Replace them after the cable is installed.

Shure Incorporated

4/9

3. Align the tube into the recessed area in the center of the microphone. Install the 3 screws (removed in step 1)

to secure the tube.

Shure Incorporated

5/9

4. Drill a 143 mm (5 5/8 in.) hole through the table, and then place the tray into the hole.

Shure Incorporated

6/9

5. Guide the cable through the hole in the center of the tray. Then, place the tube through the hole in the table

and gently press the microphone into the tray. Align the Shure logo on the microphone with the Shure logo on

the tray. The four rubber feet on the bottom of the microphone fit into the four smaller holes in the tray.

Shure Incorporated

7/9

6. Place the bracket underneath the table, with the tube going through the hole. For thicker tables (≥ 55 mm), turn

the bracket upside down for additional clearance.

Note: maximum table thickness = 73 mm (2.87 in).

Shure Incorporated

8/9

7. Guide the cable through the wing nut, and attach the wing nut onto the tube from underneath the table. Then,

tighten the wing nut to secure the bracket against the table.

Optional: use the hole in the wing nut to insert a cable tie for cable management.

Shure Incorporated

9/9

Dimensions

Otros manuales para A310-FM

Tabla de contenidos

Otros manuales de Rack y soporte de Shure

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario