Shure INTELLIMIX P300 Instrucciones originales
1/96
Safety Information
IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accor
dance with the manufacturer’s instructions.
8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other appara
tus (including amplifiers) that produce heat. Do not place any open flame sources on the product.
9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.
14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been dam
aged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vas
es, on the apparatus.
16. The MAINS plug or an appliance coupler shall remain readily operable.
17. The airborne noise of the Apparatus does not exceed 70dB (A).
Safety Information Shure Incorporated
2/96
18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing
connection.
19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.
21. Operate this product within its specified operating temperature range.
Note: Model information and power ratings are labeled on the bottom of the unit.
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within
this unit.
This symbol indicates that there are important operating and maintenance instructions in the litera
ture accompanying this unit.
Overview
General Description
The P300 IntelliMix® Audio Conferencing Processor offers IntelliMix DSP algorithms optimized for audio / video
conferencing applications, featuring 8 channels of acoustic echo cancellation, noise reduction and automatic gain
control to ensure a high-quality audio experience.
The P300 provides Dante (10 in / 2 out), Analog (2 block in / 2 block out), USB (1 in / out) and Mobile (3.5 mm)
connectivity options that makes connecting to room systems and collaborating with laptops and mobile devices
easier than ever
Features
• Connects 10 Dante™ audio inputs, 2 analog inputs, USB, and a mobile device to an A/V conferencing system
or a PC-based videoconferencing application
•Includes Shure DSP algorithms to enhance audio quality in A/V conferences: 8 channels of AEC (acoustic echo
cancellation), noise reduction, and automatic gain control, combined with IntelliMix automatic mixing, matrix
mixing, delay, compressor and parametric equalization
• Flexible signal routing and connectivity: analog audio (2 block in / 2 block out) to connect to room A / V confer
encing system; USB (1 in / out) to connect to laptop or room PC; one 3.5 mm TRRS jack to connect to a mobile
device to enable an additional participant to join
•Power over Ethernet Plus (PoE+) eliminates the need for an outboard power supply
•Compact form factor is easy to mount without equipment rack
Safety Information Shure Incorporated
3/96
Getting Started
This device features a browser-based web application, which controls audio and network properties. Upon com
pleting this basic setup process, you will be able to:
•Access the web application to customize audio settings, signal routing, and network properties
•Use Dante Controller software to connect with other Dante devices and pass audio
•Access additional configuration information
Step 1: Connect to a Network
1. Use an Ethernet cable (CAT5e or higher) to connect the P300 to a network switch.
Note: The network switch must provide Power over Ethernet Plus (PoE+). Make sure to connect to a PoE+
port, since many switches do not supply power on all ports.
2. Connect a computer to the network switch with an Ethernet cable
Step 2: Access the Web Application
1. Download and install the Shure Device Discovery application (http://www.shure.com)
2. Open the Shure Device Discovery application
3. Double-click the device to open the web application.
Tip: If setting up multiple Shure devices, use the Identify button in the application to flash the lights on the de
vice.
Safety Information Shure Incorporated
4/96
Step 3: Connect Devices in Dante Controller Soft
ware
1. Download and install Dante Controller Software from http://www.audinate.com
2. Use Dante Controller to create connections with other Dante devices.
3. Important: For Shure devices with integrated automatic mixing (such as the MXA910), connect independent
channels to the P300 Dante input channels to ensure effective acoustic echo cancellation.
Note: Refer to the Dante Controller user guide for more information on channel routing (available at http://
www.audinate.com/resources/technical-documentation)
Safety Information Shure Incorporated
5/96
Example: Connecting the P300 and Shure MXA910
1. Find the MXA910 in the list of Dante transmitters, and select the plus sign (+) to show all channels.
2. Find the P300 in the list of Dante receivers, and select the plus sign (+) to show all channels.
3. Connect channels 18 from the MXA910 to Dante input channels 18 on the P300. Do not use the automix out
put from the MXA910 into the P300.
Step 4: Configure Audio
The final configuration steps will vary, depending on the signal processing required and hardware connected to the
P300. These steps provide a general guideline. Specific steps are included in the system examples.
1. Connect analog, USB, and mobile audio devices
Safety Information Shure Incorporated
6/96
2. Route signals in the matrix mixer
3. Adjust input and output levels in the input and output tabs
4. Turn on digital signal processing blocks as needed
5. Set the AEC reference channel by opening the AEC menu in the schematic view or inputs tab and selecting a
channel from the pull-down menu. Use the channel that carries audio to loudspeakers as the AEC reference.
Analog -- To Speaker is the most common channel for this application, in configurations using an analog loud
speaker system or the built-in speaker on a display.
More comprehensive information is available in the help section of the web application.
Safety Information Shure Incorporated
7/96
Get More Information
Now that the basic setup is complete, you should have access to the web application and be able to pass audio
between devices. More comprehensive information is available online and in the help section, including:
•Maximizing audio quality with the built-in parametric equalizer
•External control system command strings
•Signal routing
•System scenario diagrams
•Software configuration
•Networking information
•Troubleshooting
•Replacement parts and accessories
The complete user guide is available at http://pubs.shure.com/guide/P300 (http://pubs.shure.com/guide/ANIUSB-
MATRIX)
System Planning and Gear Requirements
USB Computer System
1. Connect the computer to the USB port on the P300
Safety Information Shure Incorporated
8/96
2. Connect a powered loudspeaker or amplifier to the P300 analog output 2. In the matrix mixer, this is labeled
Analog - To Speaker.
3. In the P300 web application, open the matrix mixer to make connections between devices.
Note: Some connections are established in the matrix mixer by default. Refer to the matrix mixer help topic in
the web application for additional information.
Required Matrix Mixer Connections:
Input Output
Automix USB output
USB input Analog - To Speaker
4. In the schematic view, right-click any AEC block and set the AEC reference channel to Analog - To Speaker.
5. In the web application, adjust input and output levels and perform a sound check. Refer to the help topics in the
web application for additional information.
Connecting a USB Device
The USB port connects the host computer to the entire room audio system, including microphones and loudspeak
ers.
When the P300 is connected for the first time, the computer recognizes it as a USB audio device. You may need to
select it as the input/output (recording/playback) device to pass audio. Assign the P300 as the default device to
ensure it passes audio every time it is plugged in. Refer to the manual for your computer to configure the audio
settings.
Adapter Compatibility
This device is compatible with USB-B to USB-C adapters. Using an adapter is only recommended for desktop and
laptop computers, as many mobile devices do not support bi-directional audio through USB or lightning ports.
Safety Information Shure Incorporated
9/96
Hardware Codec System
1. Connect the hardware codec audio output to the P300 analog input 1. In the matrix mixer, this is labeled Ana
log - From Codec.
2. Connect the hardware codec audio input to the P300 analog output 1. In the matrix mixer, this is labeled Ana
log - To Codec.
3. Connect a powered loudspeaker or amplifier to the P300 analog output 2. In the matrix mixer, this is labeled
Analog - To Speaker.
4. In the P300 web application, open the matrix mixer to make connections between devices.
Note: Some connections are established in the matrix mixer by default. Refer to the matrix mixer help topic in
the web application for additional information.
Required Matrix Mixer Connections:
Input Output
Automix Analog - To codec
Analog - From Codec Analog - To Speaker
5. In the schematic view, right-click any AEC block and set the AEC reference channel to Analog - To Speaker.
6. In the web application, adjust input and output levels and perform a sound check. Refer to the help topics in the
web application for additional information.
Safety Information Shure Incorporated
10/96
Mobile Phone System
In this example, when the phone is plugged in, the builtin microphone and speaker are disabled the phone sim
ply carries the call. The MXA310 microphone captures near-end audio, and the loudspeaker delivers audio from
the far end of the call.
1. Connect the phone to the P300 with a 1/8-inch TRRS cable
2. Connect a powered loudspeaker or amplifier to the P300 analog output 2. In the matrix mixer, this is labeled
Analog - To Speaker.
3. In the P300 web application, open the matrix mixer to make connections between devices.
Note: Some connections are established in the matrix mixer by default. Refer to the matrix mixer help topic in
the web application for additional information.
Required Matrix Mixer Connections:
Input Output
Automix Mobile output
Mobile input Analog - To Speaker
4. In the schematic view, right-click any AEC block and set the AEC reference channel to Analog - To Speaker.
Otros manuales para INTELLIMIX P300
3
Tabla de contenidos
Otros manuales de Sistema de conferencias de Shure
Shure
Shure MXW6W Manual de usuario
Shure
Shure DDS 5900 Manual de usuario
Shure
Shure DDS 5900 Manual de usuario
Shure
Shure Microflex Complete Manual de usuario
Shure
Shure MX890 Manual de usuario
Shure
Shure DT 6008 Manual de usuario
Shure
Shure Microflex Complete MXC Series Manual de usuario
Shure
Shure MXCW Manual de usuario
Shure
Shure MU 6040D Manual de usuario
Shure
Shure DCS 6000 Manual de usuario
Shure
Shure CP 7890 Manual de usuario
Shure
Shure IS 6132 Manual de usuario
Shure
Shure MXA902 Manual de usuario
Shure
Shure Microflex Manual del propietario
Shure
Shure FC 6021 Manual de usuario
Shure
Shure Microflex MXW1 Manual de usuario
Shure
Shure DDS 5900 Manual de usuario
Shure
Shure INTELLIMIX P300 Manual de usuario
Shure
Shure RP 6004 Manual de usuario
Shure
Shure IntelliMix Room Manual de usuario
Manuales populares de Sistema de conferencias de otras marcas
Kramer
Kramer VIA GO Manual de usuario
AVT
AVT MAGIC AC1 Go Manual de usuario
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manual de usuario
Sony
Sony PCS-I150 Manual de usuario
Middle Atlantic Products
Middle Atlantic Products VTC Series Manual de usuario
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guía
