- English -
4 English
• At welding mode 3 functions can be adjusted
1. Sensitivity
2. Shade
3. Delay
• At welding mode, short-press the button on the remote
control less than 1 sec and release, the function will be
changed circularly during shade, sensitivity and delay
time.
6. VARIABLE SHADE CONTROL
If the shade is in the range 5-9 or range of 9-13, clockwise rotate
the button on the remote control, shade number will be increased;
or anticlockwise rotate the button on the remote control, shade
number will be reduced.
Note
• Choose an optimum shade number for the required
welding process or application (see table 1)
• If the ADF does not darken when striking arc, stop
welding immediately and contact our representative
7. SENSITIVITY CONTROL
The responsiveness to different light levels in various welding
processes can be adjusted in the range 1-5 (from low to high).
Senstivity can only be adjusted at welding mode.
• Short press the button (8) on the remote control and
select SENS and clockwise rotate the button on the
remote control, sensitivity will be increased; or
anticlockwise rotate the button on the remote control,
sensitivity will be reduced. After the icon 6 mentioned is
displayed on the screen, number can be changed
in the range of 1 to 5.
a. Turn to level 1 (low): The sensitivity changes to be
lower.
• Suitable for high amperage welding and
welding in bright light conditions (lamp light or
sun light).
b. Turn to level 5 (high): The sensitivity changes to be
higher.
• Suitable for low amperage welding and using
in poor light conditions.
• Suitable for using with steady arc process
such as TIG welding.
• Under normally use, a higher sensitivity
setting is recommended.
8. DELAY CONTROL
The length of time delay for the ADF returns to light state after
welding can be adjusted in the range 1-5 (for 0.1~0.9s). The time
delay is for protection of welder’s eyes from strong residual rays
after welding.
• Short press the button (8) on the remote control and
select DELAY and clockwise rotate the button on the
remote control, delay time will be increased; or
anticlockwise rotate the button on the remote control,
delay time will be reduced. After the icon 7 mentioned is
displayed on the screen, number will be changed in
the range of 1 to 5.
a. Turn to level 1 (0.1s): The time the ADF lighten after
welding to be shorter. The shortest time is about 0.1s
depending upon welding point temperature and
shade set. This setting is ideal for track welding or
production welding with short welds.
b. Turn to level 5 (0.9s): The time the ADF lighten after
welding to be longer. The longest time is about 0.9s
depending upon welding point temperature and
shade set. This setting is ideal for welding at high
amperage where there is an after-glow from the weld.
9. GRINDING SELECTION
Select grinding mode by pressing the button on the remote
control, picture 3 mentioned will show on the remote control and
the orange light on ADF will ash.
Note
• Do not weld in the grinding mode, the ADF will not
darken.
10. CUTTING SELECTION
Select cutting mode by long pressing the button on the remote
control for 2 sec and release, picture 4 will show on the remote
control and the orange light on ADF will ash.
Note
• Do not weld in the cutting mode.
11. BATTERY INDICATOR
Icon 1 mentioned indicates the remote control battery status.
Charge the battery when it is low, otherwise, the remote control
will be out of work.
Charge the battery of ADF when the light on ADF becomes
red. Otherwise, switching time will become slower and shade
accuracy will be compromised.
12. POWER SUPPLY AND CHARGING
The power of the auto-darkening helmet is provided by solar cells
and rechargeable lithium battery.
Charge battery with Micro-USB cable when battery is low (5&6)
