Shimpo DT209X Manual de usuario

Thank you for your purchase of this Shimpo Product. This manual explains how

to operate your equipment safely and correctly. The manual covers the various

different features of the DT-209X. Kindly read this manual thoroughly before

operation as it holds important information that will help you fully utilize this unit.

Caution warning holds important safety information

Reminder: holds important key information for the product.

Warning: Laser equipped product. Observe caution

DT-209X Handheld Digital Laser Tachometer

Table of Contents

Section I – Handheld Tachometer

• Description of Parts………………………………………………………………………….………1

• Description LCD Display…………………………………………………………………….………3

• Unit Selector Switch………………………………………………………………………………….4

• Abbreviation of Display Table………………………………………………………………………5

• Power Supply…………………………………………………………………………………………6

• Measurement Modes………………………………………………………………………………...7

• Flow Chart Diagram………………………………………………………………………………….8

o Standard Mode

o Average Mode

o USB Mode

• Measuring Methods ……………………………………………………… ……………………….10

• Mode Operation…………………………………………………………………………………….13

o Display Explanation

• Memory Function…………………………………………………………………………………...17

• Other Function………………………………………………………………………………………20

o Memory Deletion

• Analog Output ………………………………………………………………………………………21

• Replacing Batteries…………………………………………………………………………………22

• Specifications……………………………………………………………………………………….23

• Accessories………………………………………………………………………………………….24

Section II – Software……………………………………………………………………………………...27

• DT-209X API Section

o Software Compatibility

o Advantages of USB

o Different Modes

• DT-209X API-CD Checklist………………………………………………………………………….28

• DT-209X USB Driver Installation……………………………………………………………………29

• Application Software Installation……………………………………………………………….……30

• Main Screen Description ……………………………………………………………………….… …36

• LCD Display………………………………………………………………………………………….39

• Unit Selector Switch………………………………………………………………………………….40

• USB Mode Screen……………………………………………………………………………… ……41

• USB Mode Graph Screen………………………………………………………………………… ….51

• Standard Mode Screen……………………………………………………………………………. …53

• Average Mode Screen…………………………………………………………………………….. …57

• Display Hold…………..…………………………………………………………………………… ..62

• Troubleshooting Section ……………………………………………………………………………..63

Model DT-209X casing is similar to standard DT-207/DT-205L with addition of

USB port, analog output, and selector switch.

DT-209X Parts Description

9. Power Switch

3. Measurement Mode Selector

6. Laser Beam O

enin

1. USB Connector

7. Dis

5. Contact Adapter

(DT-ADP-200L)

4. Contact

2. Analo

Out

8. Unit Selector Switch

10. Memory Button

Parts Function

1 USB Connector Mini-USB connector for PC online measurements and data

downloads.

2 Analog Output

Connector

0 to 1-volt analog output connector for pen recorders and other

external devices.

3 Measurement Mode

Selector Switch

Slide selector switch for different measuring modes. (USB,

Average, STD).

4 Contact Accessories

Contact attachments for contact measurements. Types of

attachments: Funnel, Cone, and FPM wheel (length

measurements).

5 Contact Adapter Threaded adapter for contact measurements. It can be

installed easily on top of the laser opening. (DT-ADP-200L).

6 Laser Beam

Opening

Output opening for laser diode. (Laser beam Max output: 1

mW. Continuous Wavelength: 670nm).

For Non-contact operation the reflective tape is placed on the

rotating object. When the reflective tape passes the laser a

count is generated.

Effective distance from object to be measured can be from 127

mm to 1.5m (5 inches to 59 inches).

*Measuring Conditions: On reflective surfaces, it may be

necessary to paint the shaft black, to minimize false activation

of the sensor. Reflective tape size and the radius of the

moving object should be considered to get the most accurate

reading from the tachometer.

Warning: Do not look into the laser beam opening while in

operation. Staring at the laser beam directly can cause

eye damage.

7 Display LCD main display 5digits/ Custom Words and Units.

Units of measure are selected from this switch.

Proper contact tip accessory should be used for operation.

Rotation

Speed

Measurement

RPM

Linear Speed

Measurement M/min-yd/min-ft/min-in/min

8 Unit Selector Switch

Contact

Length

Measurement

(wheel

required)

in /ft/yd/ m

Non-

Contact

Rotation Speed

Measurement RPM

Non- USB Mode

(No cable

connected)

ON and OFF switch and block separator.

For standard and average mode the power

switch button is required while taking

readings. Failure to press the power button

will not permit measurements. Pressing the

memory button while holding the power

button, allows sample points to be captured.

Releasing the power button advances the

memory per block. If the tachometer is

idle for 5 minutes, the auto power off feature

will turn on to conserve battery use.

9 Power Switch

USB Mode

In USB mode this switch is inactive. The

DT-209x is in the ON state while USB cable

is connected. Voltage is supplied from the

host computer.

Non -USB Mode

Use to store data readings to DT-209X on

board memory.

Recalls stored data from the tachometer

10 Memory Button

USB Mode Switch is inactive when the tachometer is

connected to the PC via USB port.

Description LCD Display

Unit Selector Switch

Multi-mode capability measures RPM, mPM, YPM, FPM, IPM and total meters,

yards, feet and inches.

NOTE: Selector switch not available in USB mode; all controls are

transferred to the software through the USB cable.

Measurement

method Explanation of Operation

Contact measurement requires the contact adapter

(DT-ADP-200L) and the proper attachments.

NOTE: Make sure that proper position of the knob is

selected. For length and linear rate measurements

wheel is required to get right ratio. (FPM-6, FPM-12).

For rotational

speed

measurements

RPM (rev/MIN) –Cone tip, Funnel tip

For speed

measurements

m/MIN - yd/MIN - ft/MIN - in/MIN

(6” or 12” circumference wheel).

Contact Type

For length

measurements

in / ft / yd / m (6” or 12”

circumference wheel)

Non-contact measurement requires the use of the

laser and a reflective tape. Choose the correct

settings with the Unit Selector Switch.

CAUTION: Laser Beam Radiation. Do not stare

into beam.

Non-Contact Type

rotational

speed

measurement

RPM (rev/MIN)

Operation

• The switch selector can be turned clockwise or counter-clockwise

depending on which unit of measure is required.

• The unit of measure selected on the dial is indicated in the digital display.

• Conversion of units –measured values can be automatically converted to

the unit selector switch.

Limitation: Conversion is limited to the same group of values (example

RPM cannot be converted to inches).

• Dashes will show on the display when invalid selection is made.

Abbreviation Display Table

Setting Display Meaning

RPM RPM-Revolutions per minute

m/M Meters per minute

Y/M Yards per minute

f/m Feet per minute

I/M Inches per minute

IN Inches

fT Feet

YR Yards

Unit

m Meters

Usb USB mode

STd Standard mode

AVE Average mode or average data

display

LST Last measurement recorded

M1~M10 Memory number in Standard Mode

Mode

NOO~N30

Block number (Average:30 memory

blocks max, Standard: 24 memory

blocks max)

Additional Displays

Setting Display Meaning

Measurement 5 figure digits

Depending on which mode is

selected, and the range of

measurements the decimal point may

not be available. For better resolution

use USB mode and DT-209X

software.

LoAd Storing data readingState

rEAdy Tachometer ready to accept readings

FULL Full memory indicator (the unit cannot

store additional data)

CCCCC

Clear data from memory. Holding

memory button for 5 seconds will

clear stored data per block in

Standard and Average modes. For

USB operation, CCCCC indicates

deletion of all stored data in the

selected measurement mode.

Power Supply

Each tachometer requires 2 AA batteries to operate.

Smart switching feature of the tachometer is active when USB cable is

connected. Each tachometer can be bus powered from the USB cable.

Note: Without the batteries the tachometer can work powered by the host

computer.

How does measurement starts?

• In USB Mode measurements starts after the start button in the software is

activated (See API section of this manual).

• In Average and Standard Modes, the tachometer starts to record data

after the power button is pressed.

When the DT-209X tachometer is turned on the following displays are shown.

This is then followed by

RPM

LoAd

Load message from the LCD

indicates program is initializing.

Preparing previously stored data

before it went to auto shut off

STd

rEAdy

When rEAdy message is shown

on the display, it indicates

initialization of the program is

complete.

Tabla de contenidos

Otros manuales de Instrumento de medición de Shimpo

Shimpo

Shimpo FG-7000T Manual de usuario

Shimpo

Shimpo DT-721 Manual de usuario

Shimpo

Shimpo DT-5TG Manual de usuario

Shimpo

Shimpo DT-5TXR Manual de usuario

Shimpo

Shimpo DT-205L Manual de usuario

Shimpo

Shimpo DT-365E Manual de usuario

Shimpo

Shimpo DT-207L Manual de usuario

Shimpo

Shimpo DT-725 Manual de usuario

Shimpo

Shimpo DT-207L Manual de usuario

Shimpo

Shimpo DT-2100 Manual de usuario

Shimpo

Shimpo FG-7000L Manual de usuario

Shimpo

Shimpo PT-120 Manual de usuario

Shimpo

Shimpo CAG2000 Manual de usuario

Shimpo

Shimpo FG-7000L-M-100 Manual de usuario

Shimpo

Shimpo DRI Manual de usuario

Shimpo

Shimpo DT-326 Manual de usuario

Shimpo

Shimpo DT-5TS Manual de usuario

Shimpo

Shimpo CAG3000 Manual de usuario

Shimpo

Shimpo FGV-0.5XY Manual de usuario

Shimpo

Shimpo DT-107A Manual de usuario

Shimpo

Shimpo FG-7000 Manual de usuario

Shimpo

Shimpo DT-361 Manual de usuario

Shimpo

Shimpo FGV-0.5XY Manual de usuario

Shimpo

Shimpo DT-725 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario