Shadowspec Unity Manual de usuario

MULTI CANOPY CANTILEVER UMBRELLA
SHADOWSPEC UNITY™
www.shadowspec.com
P01/23
OWNERS MANUAL
Installation, Operation, Care and Warranty

Thank you for your purchase, we appreciate it.
Enjoy the shade, courtesy of Shadowspec.
Hello,
For a stress-free installation we suggest you read
this manual in full before assembling your new
Shadowspec Umbrella.
Help extend the life of your umbrella investment
by reading and following these care instructions
on a regular basis.

3
Warranty Informaon 4
5
Stage 1 - Key Dimensions of Your Shadowspec Unity 6
7
8
9
10
Stage 2 - Installaon of Your Umbrella Mount 11
12
14
16
18
20
21
22
Stage 3 - Assembling your Shadowspec Serenity™ 24
Stage 4 - Mounng your Shadowspec Unity™ 26
Stage 5 - Fabric Canopy Installaon 28
Stage 6 - Operang your Shadowspec Unity™ 29
Accessories - LED Lights 30
Accessories - Rainguer 31
Contents Page

4www.shadowspec.com
THE SHADOWSPEC WARRANTY:
Frame
Warranty
6 YEAR
Fabric
Warranty
10 YEAR
Warranty Information
•
•
•
•
•
*
**
**
*
**

5
Umbrella Care and Maintenance
•
•
•
•
• must
•
•
•
•
•
Tips: 1. Keep your toolkit stored in a safe place for future maintenance.
2. For commercial applications, contact us for our preventative maintenance guides.
FABRIC CLEANING INSTRUCTIONS:
Do not use heavy detergents!
For full manufacturers recommendations regarding care of our Canopy Fabrics:
global.sunbrella.com/en-us/how-to-clean for detailed care instructions.
www.shadowspec.com/register
PRODUCT REGISTRATION

6www.shadowspec.com
Key Measurement Notes:
Stage 1 - Key Dimensions of Your Shadowspec Unity
Figure A - Shadowspec Unity Umbrella Dimensions
A
BCDE
Diagram Legend
8' 2.5m 10’ 3.0m 11' 4.0m 13' 4.0m
A
Ground to central frame hub when closed* 2'10'' 860mm 2'1'' 620mm 3'7'' 866mm 2'10'' 866mm
B
Total height to top of canopy* 9’6’’ 2900mm 9’3’’ 2824mm 9’9’’ 2899mm 9’6’’ 2899mm
C
Height of umbrella to top of mast cap* 9’6’’ 2908mm 9’6’’ 2908mm 9’7’’ 2908mm 9’6’’ 2908mm
D
Ground to central frame hub when open* 7'0'' 2130mm 6'9'' 2054mm 7'3'' 2128mm 7'0'' 2128mm
E
Ground to lower outer edge of canopy* 7'3'' 2222mm 7'3'' 2219mm 7'4'' 2172mm 7'2'' 2172mm
F
Centre of Spigot to outside edge of canopy 8'8'' 2646mm 9'10'' 2973mm 11'4'' 3923mm 12'10'' 3923mm
G
Diagonal from centre of mast to corner 12'3'' 3742mm 13'10'' 4205mm N/A N/A N/A N/A
H
Duo/Quattro Umbrella Width Edge to Edge 17'4'' 5292mm 19'6'' 5946mm 22'7'' 6894mm 25'9'' 7846mm
I
Gutter Space Between Canopies 6'' 160mm 6'' 160mm N/A N/A N/A N/A
F F H
I
H
G

7
[email protected]
You will need to refer back to this page so why not earmark it for quick reference whilst you’re assembling your umbrella.
Through Spar
Through Spar
Rib Tip with
Through Spar
Rib Support
Upper Rib
Rib Tip
Figure B - Unity Umbrella Parts
Figure C - Frame Canopy Parts
Also included: Hex Key Set, No. 17 Ring Spanner
& a pot of grease for the spigot

8www.shadowspec.com
Planning your Umbrella Location.
shadowspec.com/cad
Square and Octagonal Frame Orientation
Important note: Shadowspec Unity Frames
Umbrella Mount
Square Umbrella
Octagon Umbrella
Umbrella Mount

9
Offset, Opposing & Reecting Umbrellas.
a a
d
b
c
e
Diagram Legend
2.5m 8' 3.0m 10’
a
Gap between Canopy Frames 158mm 6’’ 160mm 6’’
b
Centre of Spigot to outside edge of canopy 2648mm 8’8’’ 2980mm 9’9’’
c
Centre of Spigot to Centre of Second Serenity/Unity 2727mm 8’11’’ 3060mm 10’1’’
d
Centre of Spigot to outside edge of Second Serenity/Unity 5375mm 17’8’’ 6040mm 19’10’’
e
Centre of Spigot to Center of Second Spigot (reected) 5454mm 17’11’’ 6120mm 20’1’’

10 www.shadowspec.com
Surface Plate Alignment In-Ground Anchor Alignment
Diagram II Diagram IIIDiagram I
Bolt-hole Orientation
Mount Parallel to Structure Opening Direction
Diagram IV Diagram V
Step 1
Step 2
This will give you the orientaon, required to match exisng structures and other umbrellas.
Step 3
Step 4
Aligning your Umbrella.
Tabla de contenidos

















